Signed-off-by: Giulio Benetti <giulio.benetti@xxxxxxxxxxxxxxxx>
---
MAINTAINERS | 1 +
drivers/input/touchscreen/Kconfig | 12 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/hycon-hy46xx.c | 571 +++++++++++++++++++++++
4 files changed, 585 insertions(+)
create mode 100644 drivers/input/touchscreen/hycon-hy46xx.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 3f83daf6b2bf..7a1331657e4b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8250,6 +8250,7 @@ M: Giulio Benetti <giulio.benetti@xxxxxxxxxxxxxxxx>
L: linux-input@xxxxxxxxxxxxxxx
S: Maintained
F: Documentation/devicetree/bindings/input/touchscreen/hycon,hy46xx.yaml
+F: drivers/input/touchscreen/hy46xx.c
HYGON PROCESSOR SUPPORT
M: Pu Wen <puwen@xxxxxxxx>
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 529614d364fe..5d4751d901cb 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -1335,4 +1335,16 @@ config TOUCHSCREEN_ZINITIX
To compile this driver as a module, choose M here: the
module will be called zinitix.
+config TOUCHSCREEN_HYCON_HY46XX
+ tristate "Hycon hy46xx touchscreen support"
+ depends on I2C
+ help
+ Say Y here if you have a touchscreen using Hycon hy46xx,
+ or something similar enough.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called hycon-hy46xx.
+
endif
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 6233541e9173..8b68cf3a3e6d 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -112,3 +112,4 @@ obj-$(CONFIG_TOUCHSCREEN_ROHM_BU21023) += rohm_bu21023.o
obj-$(CONFIG_TOUCHSCREEN_RASPBERRYPI_FW) += raspberrypi-ts.o
obj-$(CONFIG_TOUCHSCREEN_IQS5XX) += iqs5xx.o
obj-$(CONFIG_TOUCHSCREEN_ZINITIX) += zinitix.o
+obj-$(CONFIG_TOUCHSCREEN_HYCON_HY46XX) += hycon-hy46xx.o
diff --git a/drivers/input/touchscreen/hycon-hy46xx.c b/drivers/input/touchscreen/hycon-hy46xx.c
new file mode 100644
index 000000000000..ef0dee9a43a9
--- /dev/null
+++ b/drivers/input/touchscreen/hycon-hy46xx.c
@@ -0,0 +1,571 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021
+ * Author(s): Giulio Benetti <giulio.benetti@xxxxxxxxxxxxxxxx>
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
+#include <linux/irq.h>
+#include <linux/regulator/consumer.h>
+
+#include <asm/unaligned.h>
+
+#define HY46XX_CHKSUM_CODE 0x1
+#define HY46XX_FINGER_NUM 0x2
+#define HY46XX_CHKSUM_LEN 0x7
+#define HY46XX_THRESHOLD 0x80
+#define HY46XX_PROX_SENS_SW 0x81
+#define HY46XX_GLOVE_EN 0x84
+#define HY46XX_REPORT_SPEED 0x88
+#define HY46XX_PWR_NOISE_EN 0x89
+#define HY46XX_FILTER_DATA 0x8A
+#define HY46XX_GAIN 0x92
+#define HY46XX_EDGE_OFFSET 0x93
+#define HY46XX_RX_NR_USED 0x94
+#define HY46XX_TX_NR_USED 0x95
+#define HY46XX_PWR_MODE 0xA5
+#define HY46XX_FW_VERSION 0xA6
+#define HY46XX_LIB_VERSION 0xA7
+#define HY46XX_TP_INFO 0xA8
+#define HY46XX_TP_CHIP_ID 0xA9
+#define HY46XX_BOOT_VER 0xB0
+
+#define HY46XX_TPLEN 0x6
+
+#define HY46XX_MAX_SUPPORTED_POINTS 11
+
+#define TOUCH_EVENT_DOWN 0x00
+#define TOUCH_EVENT_UP 0x01
+#define TOUCH_EVENT_CONTACT 0x02
+#define TOUCH_EVENT_RESERVED 0x03
+
+struct hycon_hy46xx_data {
+ struct i2c_client *client;
+ struct input_dev *input;
+ struct touchscreen_properties prop;
+ struct regulator *vcc;
+
+ struct gpio_desc *reset_gpio;
+
+ struct mutex mutex;
+
+ int threshold;
+ int proximity_sensor_switch;
+ int glove_enable;
+ int report_speed;
+ int power_noise_enable;
+ int filter_data;
+ int gain;
+ int edge_offset;
+ int rx_number_used;
+ int tx_number_used;
+ int power_mode;
+ int fw_version;
+ int lib_version;
+ int tp_information;
+ int tp_chip_id;
+ int bootloader_version;
+};
+
+static int hycon_hy46xx_readwrite(struct i2c_client *client, u16 wr_len, u8 *wr_buf,
+ u16 rd_len, u8 *rd_buf)
+{
+ struct i2c_msg msgs[2];
+ int i = 0;
+ int ret;
+
+ if (wr_len) {
+ msgs[i].addr = client->addr;
+ msgs[i].flags = 0;
+ msgs[i].len = wr_len;
+ msgs[i].buf = wr_buf;
+ i++;
+ }
+ if (rd_len) {
+ msgs[i].addr = client->addr;
+ msgs[i].flags = I2C_M_RD;
+ msgs[i].len = rd_len;
+ msgs[i].buf = rd_buf;
+ i++;
+ }
+
+ ret = i2c_transfer(client->adapter, msgs, i);
+ if (ret < 0)
+ return ret;
+ if (ret != i)
+ return -EIO;
+
+ return 0;
+}
Please see if your driver could be converted to regmap API instead of
"maked" i2c. It will allow using write-gather when system supports it,
etc.
+
+static bool hycon_hy46xx_check_checksum(struct hycon_hy46xx_data *tsdata, u8 *buf)
+{
+ u8 chksum = 0;
+ int i;
+
+ for (i = 2; i < buf[HY46XX_CHKSUM_LEN]; i++)
+ chksum += buf[i];
+
+ if (chksum == buf[HY46XX_CHKSUM_CODE])
+ return true;
+
+ dev_err_ratelimited(&tsdata->client->dev,
+ "checksum error: 0x%02x expected, got 0x%02x\n",
+ chksum, buf[HY46XX_CHKSUM_CODE]);
+
+ return false;
+}
+
+static irqreturn_t hycon_hy46xx_isr(int irq, void *dev_id)
+{
+ struct hycon_hy46xx_data *tsdata = dev_id;
+ struct device *dev = &tsdata->client->dev;
+ u8 rdbuf[0x44];
A #define here would be nice.
A #define here would be nice.
+ u8 cmd;
+ int i, x, y, id;
+ int error;
+
+ memset(rdbuf, 0, sizeof(rdbuf));
+
+ error = hycon_hy46xx_readwrite(tsdata->client, 1, &cmd, sizeof(rdbuf), rdbuf);
cmd could be any garbage (as it is uninitialized)? This requires a nice
comment as to why it is OK.
+ if (error) {
+ dev_err_ratelimited(dev, "Unable to fetch data, error: %d\n",
+ error);
+ goto out;
+ }
+
+ if (!hycon_hy46xx_check_checksum(tsdata, rdbuf))
+ goto out;
+
+ for (i = 0; i < HY46XX_MAX_SUPPORTED_POINTS; i++) {
+ u8 *buf = &rdbuf[3 + (HY46XX_TPLEN * i)];
+ int type = buf[0] >> 6;
+
+ if (type == TOUCH_EVENT_RESERVED)
+ continue;
+
+ x = get_unaligned_be16(buf) & 0x0fff;
+ y = get_unaligned_be16(buf + 2) & 0x0fff;
+
+ id = (buf[2] >> 4) & 0x0f;
buf is u8 so no need to additionally mask after shifting.
+
+ input_mt_slot(tsdata->input, id);
+ if (input_mt_report_slot_state(tsdata->input, MT_TOOL_FINGER,
+ type != TOUCH_EVENT_UP))
+ touchscreen_report_pos(tsdata->input, &tsdata->prop,
+ x, y, true);
+ }
+
+ input_mt_report_pointer_emulation(tsdata->input, true);
+ input_sync(tsdata->input);
+
+out:
+ return IRQ_HANDLED;
+}
+
+static int hycon_hy46xx_register_write(struct hycon_hy46xx_data *tsdata, u8 addr, u8 value)
+{
+ u8 wrbuf[2];
+
+ wrbuf[0] = addr;
+ wrbuf[1] = value;
+
+ return hycon_hy46xx_readwrite(tsdata->client, 2, wrbuf, 0, NULL);
+}
+
+static int hycon_hy46xx_register_read(struct hycon_hy46xx_data *tsdata, u8 addr)
+{
+ u8 wrbyte, rdbyte;
+ int error;
+
+ wrbyte = addr;
+ error = hycon_hy46xx_readwrite(tsdata->client, 1, &wrbyte, 1, &rdbyte);
+ if (error)
+ return error;
+
+ return rdbyte;
+}
+
+struct hycon_hy46xx_attribute {
+ struct device_attribute dattr;
+ size_t field_offset;
+ u8 address;
+ u8 limit_low;
+ u8 limit_high;
+};
+
+#define HYCON_ATTR(_field, _mode, _address, _limit_low, _limit_high) \
+ struct hycon_hy46xx_attribute hycon_hy46xx_attr_##_field = { \
+ .dattr = __ATTR(_field, _mode, \
+ hycon_hy46xx_setting_show, \
+ hycon_hy46xx_setting_store), \
+ .field_offset = offsetof(struct hycon_hy46xx_data, _field), \
+ .address = _address, \
+ .limit_low = _limit_low, \
+ .limit_high = _limit_high, \
+ }
+
+static ssize_t hycon_hy46xx_setting_show(struct device *dev,
+ struct device_attribute *dattr, char *buf)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct hycon_hy46xx_data *tsdata = i2c_get_clientdata(client);
+ struct hycon_hy46xx_attribute *attr =
+ container_of(dattr, struct hycon_hy46xx_attribute, dattr);
+ u8 *field = (u8 *)tsdata + attr->field_offset;
+ int val;
+ size_t count = 0;
+ int error = 0;
+ u8 addr = attr->address;
+
+ mutex_lock(&tsdata->mutex);
+
+ val = hycon_hy46xx_register_read(tsdata, addr);
+ if (val < 0) {
+ error = val;
+ dev_err(&tsdata->client->dev,
+ "Failed to fetch attribute %s, error %d\n",
+ dattr->attr.name, error);
+ goto out;
+ }
+
+ if (val != *field) {
+ dev_warn(&tsdata->client->dev,
+ "%s: read (%d) and stored value (%d) differ\n",
+ dattr->attr.name, val, *field);
+ *field = val;
+ }
+
+ count = scnprintf(buf, PAGE_SIZE, "%d\n", val);
+out:
+ mutex_unlock(&tsdata->mutex);
+ return error ?: count;
+}
+
+static ssize_t hycon_hy46xx_setting_store(struct device *dev,
+ struct device_attribute *dattr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct hycon_hy46xx_data *tsdata = i2c_get_clientdata(client);
+ struct hycon_hy46xx_attribute *attr =
+ container_of(dattr, struct hycon_hy46xx_attribute, dattr);
+ u8 *field = (u8 *)tsdata + attr->field_offset;
+ unsigned int val;
+ int error;
+ u8 addr = attr->address;
+
+ mutex_lock(&tsdata->mutex);
+
+ error = kstrtouint(buf, 0, &val);
+ if (error)
+ goto out;
+
+ if (val < attr->limit_low || val > attr->limit_high) {
+ error = -ERANGE;
+ goto out;
+ }
+
+ error = hycon_hy46xx_register_write(tsdata, addr, val);
+ if (error) {
+ dev_err(&tsdata->client->dev,
+ "Failed to update attribute %s, error: %d\n",
+ dattr->attr.name, error);
+ goto out;
+ }
+ *field = val;
I am not sure why you want this check (I see that we have it in one
other driver and I really do not recall why we have it there either).
+
+out:
+ mutex_unlock(&tsdata->mutex);
+ return error ?: count;
+}
+
+static HYCON_ATTR(threshold, 0644, HY46XX_THRESHOLD, 0, 255);
+static HYCON_ATTR(proximity_sensor_switch, 0644, HY46XX_PROX_SENS_SW, 0, 1);
+static HYCON_ATTR(glove_enable, 0644, HY46XX_GLOVE_EN, 0, 1);
+static HYCON_ATTR(report_speed, 0644, HY46XX_REPORT_SPEED, 0, 255);
+static HYCON_ATTR(power_noise_enable, 0644, HY46XX_PWR_NOISE_EN, 0, 1);
+static HYCON_ATTR(filter_data, 0644, HY46XX_FILTER_DATA, 0, 5);
+static HYCON_ATTR(gain, 0644, HY46XX_GAIN, 0, 5);
+static HYCON_ATTR(edge_offset, 0644, HY46XX_EDGE_OFFSET, 0, 5);
+static HYCON_ATTR(fw_version, 0444, HY46XX_FW_VERSION, 0, 255);
+static HYCON_ATTR(lib_version, 0444, HY46XX_LIB_VERSION, 0, 255);
+static HYCON_ATTR(tp_information, 0444, HY46XX_TP_INFO, 0, 255);
+static HYCON_ATTR(tp_chip_id, 0444, HY46XX_TP_CHIP_ID, 0, 255);
+static HYCON_ATTR(bootloader_version, 0444, HY46XX_BOOT_VER, 0, 255);
+
+static struct attribute *hycon_hy46xx_attrs[] = {
+ &hycon_hy46xx_attr_threshold.dattr.attr,
+ &hycon_hy46xx_attr_proximity_sensor_switch.dattr.attr,
+ &hycon_hy46xx_attr_glove_enable.dattr.attr,
+ &hycon_hy46xx_attr_report_speed.dattr.attr,
+ &hycon_hy46xx_attr_power_noise_enable.dattr.attr,
+ &hycon_hy46xx_attr_filter_data.dattr.attr,
+ &hycon_hy46xx_attr_gain.dattr.attr,
+ &hycon_hy46xx_attr_edge_offset.dattr.attr,
+ &hycon_hy46xx_attr_fw_version.dattr.attr,
+ &hycon_hy46xx_attr_lib_version.dattr.attr,
+ &hycon_hy46xx_attr_tp_information.dattr.attr,
+ &hycon_hy46xx_attr_tp_chip_id.dattr.attr,
+ &hycon_hy46xx_attr_bootloader_version.dattr.attr,
+ NULL
+};
+
+static const struct attribute_group hycon_hy46xx_attr_group = {
+ .attrs = hycon_hy46xx_attrs,
+};
+
+static void hycon_hy46xx_get_defaults(struct device *dev, struct hycon_hy46xx_data *tsdata)
+{
+ u32 val;
+ int error;
+
+ error = device_property_read_u32(dev, "threshold", &val);
+ if (!error) {
+ hycon_hy46xx_register_write(tsdata, HY46XX_THRESHOLD, val);
+ tsdata->threshold = val;
+ }
+
+ error = device_property_read_u32(dev, "proximity-sensor-switch", &val);
+ if (!error) {
+ hycon_hy46xx_register_write(tsdata, HY46XX_PROX_SENS_SW, val);
+ tsdata->proximity_sensor_switch = val;
+ }
+
+ error = device_property_read_u32(dev, "glove-enable", &val);
+ if (!error) {
+ hycon_hy46xx_register_write(tsdata, HY46XX_GLOVE_EN, val);
+ tsdata->glove_enable = val;
+ }
+
+ error = device_property_read_u32(dev, "report-speed", &val);
+ if (!error) {
+ hycon_hy46xx_register_write(tsdata, HY46XX_REPORT_SPEED, val);
+ tsdata->report_speed = val;
+ }
+
+ error = device_property_read_u32(dev, "power-noise-enable", &val);
+ if (!error) {
+ hycon_hy46xx_register_write(tsdata, HY46XX_PWR_NOISE_EN, val);
+ tsdata->report_speed = val;
+ }
+
+ error = device_property_read_u32(dev, "filter-data", &val);
+ if (!error) {
+ hycon_hy46xx_register_write(tsdata, HY46XX_FILTER_DATA, val);
+ tsdata->report_speed = val;
+ }
+
+ error = device_property_read_u32(dev, "gain", &val);
+ if (!error) {
+ hycon_hy46xx_register_write(tsdata, HY46XX_GAIN, val);
+ tsdata->report_speed = val;
+ }
+
+ error = device_property_read_u32(dev, "edge-offset", &val);
+ if (!error) {
+ hycon_hy46xx_register_write(tsdata, HY46XX_EDGE_OFFSET, val);
+ tsdata->report_speed = val;
+ }
+}
+
+static void hycon_hy46xx_get_parameters(struct hycon_hy46xx_data *tsdata)
+{
+ tsdata->threshold = hycon_hy46xx_register_read(tsdata, HY46XX_THRESHOLD);
+ tsdata->proximity_sensor_switch =
+ hycon_hy46xx_register_read(tsdata, HY46XX_PROX_SENS_SW);
+ tsdata->glove_enable = hycon_hy46xx_register_read(tsdata, HY46XX_GLOVE_EN);
+ tsdata->report_speed =
+ hycon_hy46xx_register_read(tsdata, HY46XX_REPORT_SPEED);
+ tsdata->power_noise_enable =
+ hycon_hy46xx_register_read(tsdata, HY46XX_PWR_NOISE_EN);
+ tsdata->filter_data = hycon_hy46xx_register_read(tsdata, HY46XX_FILTER_DATA);
+ tsdata->gain = hycon_hy46xx_register_read(tsdata, HY46XX_GAIN);
+ tsdata->edge_offset = hycon_hy46xx_register_read(tsdata, HY46XX_EDGE_OFFSET);
+ tsdata->rx_number_used =
+ hycon_hy46xx_register_read(tsdata, HY46XX_RX_NR_USED);
+ tsdata->tx_number_used =
+ hycon_hy46xx_register_read(tsdata, HY46XX_TX_NR_USED);
+ tsdata->power_mode = hycon_hy46xx_register_read(tsdata, HY46XX_PWR_MODE);
+ tsdata->fw_version = hycon_hy46xx_register_read(tsdata, HY46XX_FW_VERSION);
+ tsdata->lib_version = hycon_hy46xx_register_read(tsdata, HY46XX_LIB_VERSION);
+ tsdata->tp_information = hycon_hy46xx_register_read(tsdata, HY46XX_TP_INFO);
+ tsdata->tp_chip_id = hycon_hy46xx_register_read(tsdata, HY46XX_TP_CHIP_ID);
+ tsdata->bootloader_version =
+ hycon_hy46xx_register_read(tsdata, HY46XX_BOOT_VER);
+}
+
+static void hycon_hy46xx_disable_regulator(void *arg)
+{
+ struct hycon_hy46xx_data *data = arg;
+
+ regulator_disable(data->vcc);
+}
+
+static int hycon_hy46xx_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ const struct hycon_hy46xx_i2c_chip_data *chip_data;
Where is this defined??
+ struct hycon_hy46xx_data *tsdata;
+ struct input_dev *input;
+ unsigned long irq_flags;
+ int error;
+
+ dev_dbg(&client->dev, "probing for HYCON HY46XX I2C\n");
+
+ tsdata = devm_kzalloc(&client->dev, sizeof(*tsdata), GFP_KERNEL);
+ if (!tsdata)
+ return -ENOMEM;
+
+ chip_data = device_get_match_data(&client->dev);
+ if (!chip_data)
+ chip_data = (const struct hycon_hy46xx_i2c_chip_data *)
+ id->driver_data;
+ if (!chip_data) {
+ dev_err(&client->dev, "invalid or missing chip data\n");
+ return -EINVAL;
+ }
You are not attaching any additional data to OF or legacy match tables,
so why are you doing this?
+
+ tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
+ if (IS_ERR(tsdata->vcc)) {
+ error = PTR_ERR(tsdata->vcc);
+ if (error != -EPROBE_DEFER)
+ dev_err(&client->dev,
+ "failed to request regulator: %d\n", error);
+ return error;
+ }
+
+ error = regulator_enable(tsdata->vcc);
+ if (error < 0) {
+ dev_err(&client->dev, "failed to enable vcc: %d\n", error);
+ return error;
+ }
+
+ error = devm_add_action_or_reset(&client->dev,
+ hycon_hy46xx_disable_regulator,
+ tsdata);
+ if (error)
+ return error;
+
+ tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
+ "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(tsdata->reset_gpio)) {
+ error = PTR_ERR(tsdata->reset_gpio);
+ dev_err(&client->dev,
+ "Failed to request GPIO reset pin, error %d\n", error);
+ return error;
+ }
+
+ if (tsdata->reset_gpio) {
+ usleep_range(5000, 6000);
+ gpiod_set_value_cansleep(tsdata->reset_gpio, 1);
+ usleep_range(5000, 6000);
+ gpiod_set_value_cansleep(tsdata->reset_gpio, 0);
+ msleep(1000);
+ }
+
+ input = devm_input_allocate_device(&client->dev);
+ if (!input) {
+ dev_err(&client->dev, "failed to allocate input device.\n");
+ return -ENOMEM;
+ }
+
+ mutex_init(&tsdata->mutex);
+ tsdata->client = client;
+ tsdata->input = input;
+
+ hycon_hy46xx_get_defaults(&client->dev, tsdata);
+ hycon_hy46xx_get_parameters(tsdata);
+
+ input->name = "Hycon Capacitive Touch";
+ input->id.bustype = BUS_I2C;
+ input->dev.parent = &client->dev;
+
+ input_set_abs_params(input, ABS_MT_POSITION_X,
+ 0, -1, 0, 0);
+ input_set_abs_params(input, ABS_MT_POSITION_Y,
+ 0, -1, 0, 0);
+
+ touchscreen_parse_properties(input, true, &tsdata->prop);
+
+ error = input_mt_init_slots(input, HY46XX_MAX_SUPPORTED_POINTS,
+ INPUT_MT_DIRECT);
+ if (error) {
+ dev_err(&client->dev, "Unable to init MT slots.\n");
+ return error;
+ }
+
+ i2c_set_clientdata(client, tsdata);
+
+ irq_flags = irq_get_trigger_type(client->irq);
+ if (irq_flags == IRQF_TRIGGER_NONE)
+ irq_flags = IRQF_TRIGGER_FALLING;
+ irq_flags |= IRQF_ONESHOT;
Just use IRQF_ONESHOT. The construct above is for compatibility when we
had drivers in the tree that were hard-coding trigger, and then we moved
to specify trigger in platform code/ACPI/DT and wanted to limit
regressions. Given this driver is brand new simply pass IRQF_ONESHOT
into devm_request_threaded_irq() below and call it a day.
+
+ error = devm_request_threaded_irq(&client->dev, client->irq,
+ NULL, hycon_hy46xx_isr, irq_flags,
+ client->name, tsdata);
+ if (error) {
+ dev_err(&client->dev, "Unable to request touchscreen IRQ.\n");
+ return error;
+ }
+
+ error = devm_device_add_group(&client->dev, &hycon_hy46xx_attr_group);
+ if (error)
+ return error;
+
+ error = input_register_device(input);
+ if (error)
+ return error;
+
+ dev_dbg(&client->dev,
+ "HYCON HY46XX initialized: IRQ %d, Reset pin %d.\n",
+ client->irq,
+ tsdata->reset_gpio ? desc_to_gpio(tsdata->reset_gpio) : -1);
+
+ return 0;
+}
+
+static const struct i2c_device_id hycon_hy46xx_id[] = {
+ { .name = "hycon-hy4613" },
+ { .name = "hycon-hy4614" },
+ { .name = "hycon-hy4621" },
+ { .name = "hycon-hy4623" },
+ { .name = "hycon-hy4633" },
+ { .name = "hycon-hy4635" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, hycon_hy46xx_id);
+
+static const struct of_device_id hycon_hy46xx_of_match[] = {
+ { .compatible = "hycon,hycon-hy4613" },
+ { .compatible = "hycon,hycon-hy4614" },
+ { .compatible = "hycon,hycon-hy4621" },
+ { .compatible = "hycon,hycon-hy4623" },
+ { .compatible = "hycon,hycon-hy4633" },
+ { .compatible = "hycon,hycon-hy4635" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, hycon_hy46xx_of_match);
+
+static struct i2c_driver hycon_hy46xx_driver = {
+ .driver = {
+ .name = "hycon_hy46xx",
+ .of_match_table = hycon_hy46xx_of_match,
+ .probe_type = PROBE_PREFER_ASYNCHRONOUS,
+ },
+ .id_table = hycon_hy46xx_id,
+ .probe = hycon_hy46xx_probe,
+};
+
+module_i2c_driver(hycon_hy46xx_driver);
+
+MODULE_AUTHOR("Giulio Benetti <giulio.benetti@xxxxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("HYCON HY46XX I2C Touchscreen Driver");
+MODULE_LICENSE("GPL v2");
--
2.25.1
Thanks.
