Hello Uwe,
On Tue, June 23, 2020 11:41 PM, Uwe Kleine-König wrote:
>
> Hello,
>
> On Mon, Jun 15, 2020 at 08:40:23PM +0900, Roy Im wrote:
> > Adds support for the Dialog DA7280 LRA/ERM Haptic Driver with multiple
> > mode and integrated waveform memory and wideband support.
> > It communicates via an I2C bus to the device.
> >
> > Signed-off-by: Roy Im <roy.im.opensource@xxxxxxxxxxx>
>
> Just some picky comments below.
>
> > + error = pwm_apply_state(haptics->pwm_dev, &state);
> > + if (error)
> > + dev_err(haptics->dev,
> > + "failed to apply pwm state: %pE\n",
> > + ERR_PTR(error));
>
> You can save some horizontal space here by dropping the \n after the first comma. (There are a few more occurences.)
>
Ok, is this what you want?
error = pwm_apply_state(haptics->pwm_dev, &state);
if (error)
dev_err(haptics->dev, "failed to apply pwm state: %pE\n",
ERR_PTR(error));
> > + return error;
> > +}
> > +[...]
> > +
> > + /* Sync up PWM state and ensure it is off. */
> > + pwm_init_state(haptics->pwm_dev, &state);
> > + state.enabled = false;
> > + error = pwm_apply_state(haptics->pwm_dev, &state);
> > + if (error) {
> > + dev_err(dev,
> > + "failed to apply initial PWM state: %pE\n",
> > + ERR_PTR(error));
> > + return error;
> > + }
> > +
> > + /* Check PWM Period, it must be in 10k ~ 250kHz */
>
> The unit of a PWM period is in (nano)seconds, to it cannot be in the range [10kHz, 250kHz]. (Is this too picky?)
No, it isn't. The 'Period' should be changed to 'frequency', I will fix this as below.
/* Check PWM frequency, valid range: 10k ~ 250kHz */
>
> > + period2freq = 1000000 / state.period;
> > + if (period2freq < DA7280_MIN_PWM_FREQ_KHZ ||
> > + period2freq > DA7280_MAX_PWM_FREQ_KHZ) {
> > + dev_err(dev, "Not supported PWM frequency(%d)\n",
> > + period2freq);
>
> Doesn't the compiler warn here about period2freq being unsigned and %d being for signed int values?
>
> For my (non-native) English ear s/Not supported/Unsupported/ sounds better. Also my eyes would be pleases by a space
> before the opening brace.
I didn't see any warning message, but I will change/improve them to proper one and the log as below.
period2freq = 1000000 / state.period;
if (period2freq < DA7280_MIN_PWM_FREQ_KHZ ||
period2freq > DA7280_MAX_PWM_FREQ_KHZ) {
dev_err(dev, "Unsupported PWM frequency (%u)\n",
period2freq);
return -EINVAL;
}
If you look ok, let me update this so.
>
> > + return -EINVAL;
> > + }
> > + }
> > +
> > +
> > +[...]
> > +static struct i2c_driver da7280_driver = {
> > + .driver = {
> > + .name = "da7280",
> > + .of_match_table = of_match_ptr(da7280_of_match),
> > + .pm = &da7280_pm_ops,
>
> I don't like alignment of =, but I'm aware this is a subjective thing.
> (The reason for me is that adding a new member that is longer than the already existing requires touching all lines. So I
> stick to a single space before a =.)
OK, I will do as you said.
>
> > + },
> > + .probe = da7280_probe,
> > + .id_table = da7280_i2c_id,
> > +};
> > +module_i2c_driver(da7280_driver);
> > +
> > +MODULE_DESCRIPTION("DA7280 haptics driver"); MODULE_AUTHOR("Roy Im
> > +<Roy.Im.Opensource@xxxxxxxxxxx>");
> > +MODULE_LICENSE("GPL");
> > --
> > end-of-patch for RESEND PATCH V13
>
> Best regards
> Uwe
>
> --
> Pengutronix e.K. | Uwe Kleine-König |
> Industrial Linux Solutions | https://www.pengutronix.de/ |
