On Sat, Feb 02, 2019 at 04:18:02PM +0100, Paweł Chmiel wrote:
> From: Jonathan Bakker <xc-racer2@xxxxxxx>
>
> Add device tree bindings for Bosch BMA150 Accelerometer Sensor
>
> Changes from v1:
> - Add properties for all of bma150_cfg
> - Correct IRQ type in example
>
> Signed-off-by: Jonathan Bakker <xc-racer2@xxxxxxx>
> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@xxxxxxxxx>
> ---
> .../bindings/input/bosch,bma150.txt | 38 +++++++++++++++++++
> include/dt-bindings/input/bma150.h | 22 +++++++++++
> include/linux/bma150.h | 13 +------
> 3 files changed, 62 insertions(+), 11 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/input/bosch,bma150.txt
> create mode 100644 include/dt-bindings/input/bma150.h
>
> diff --git a/Documentation/devicetree/bindings/input/bosch,bma150.txt b/Documentation/devicetree/bindings/input/bosch,bma150.txt
> new file mode 100644
> index 000000000000..f644d132f79c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/input/bosch,bma150.txt
> @@ -0,0 +1,38 @@
> +* Bosch BMA150 Accelerometer Sensor
> +
> +Also works for the SMB380 and BMA023 accelerometers
> +
> +Required properties:
> +- compatible : Should be "bosch,bma150"
> +- reg : The I2C address of the sensor
> +
> +Optional properties:
> +- interrupt-parent : should be the phandle for the interrupt controller
This is implied and can be dropped.
> +- interrupts : Interrupt mapping for IRQ. If not present device will be polled
> +- any-motion-int : bool for if the any motion interrupt should be enabled
> +- hg-int : bool for if the high-G interrupt should be enabled
> +- lg-int : bool for if the low-G interrupt should be enabled
> +- any-motion-cfg : array of integers for any motion duration and threshold
> +- hg-cfg : array of integers for high-G hysterisis, duration, and threshold
> +- lg-cfg : array of integers for low-G hysterisis, duration, and threshold
> +- range : configuration of range, one of BMA150_RANGE_* as defined in [1]
> +- bandwidth : refresh rate of device, one of BMA150_BW_* as defined in [1]
These all need vendor prefixes if they stay.
What determines all this configuration? It seems like a user may want to
change at run-time in which case sysfs would be more appropriate.
I don't recall seeing other accelerometers with these, but seems these
could apply to other accelerometers. In which case, they should be
common.
> +
> +Example:
> +
> +bma150@38 {
accelerometer@38
> + compatible = "bosch,bma150";
> + reg = <0x38>;
> + interrupt-parent = <&gph0>;
> + interrupts = <1 IRQ_TYPE_EDGE_RISING>;
> + any-motion-int;
> + hg-int;
> + lg-int;
> + any-motion-cfg = <0 0>;
> + hg-cfg = <0 150 160>;
> + lg-cfg = <0 150 20>;
> + range = <BMA150_RANGE_2G>;
> + bandwidth = <BMA150_BW_50HZ>;
> +};
> +
> +[1] include/dt-bindings/input/bma150.h
> diff --git a/include/dt-bindings/input/bma150.h b/include/dt-bindings/input/bma150.h
> new file mode 100644
> index 000000000000..fb38ca787f0f
> --- /dev/null
> +++ b/include/dt-bindings/input/bma150.h
> @@ -0,0 +1,22 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * This header provides bindings for the BMA150 accelerometer
> + */
> +#ifndef _DT_BINDINGS_INPUT_BMA150_H
> +#define _DT_BINDINGS_INPUT_BMA150_H
> +
> +/* Range */
> +#define BMA150_RANGE_2G 0
> +#define BMA150_RANGE_4G 1
> +#define BMA150_RANGE_8G 2
> +
> +/* Refresh rate */
> +#define BMA150_BW_25HZ 0
> +#define BMA150_BW_50HZ 1
> +#define BMA150_BW_100HZ 2
> +#define BMA150_BW_190HZ 3
> +#define BMA150_BW_375HZ 4
> +#define BMA150_BW_750HZ 5
> +#define BMA150_BW_1500HZ 6
> +
> +#endif /* _DT_BINDINGS_INPUT_BMA150_H */
> diff --git a/include/linux/bma150.h b/include/linux/bma150.h
> index 97ade7cdc870..b85266a9c35c 100644
> --- a/include/linux/bma150.h
> +++ b/include/linux/bma150.h
> @@ -20,19 +20,10 @@
> #ifndef _BMA150_H_
> #define _BMA150_H_
>
> -#define BMA150_DRIVER "bma150"
> +#include <dt-bindings/input/bma150.h>
>
> -#define BMA150_RANGE_2G 0
> -#define BMA150_RANGE_4G 1
> -#define BMA150_RANGE_8G 2
> +#define BMA150_DRIVER "bma150"
>
> -#define BMA150_BW_25HZ 0
> -#define BMA150_BW_50HZ 1
> -#define BMA150_BW_100HZ 2
> -#define BMA150_BW_190HZ 3
> -#define BMA150_BW_375HZ 4
> -#define BMA150_BW_750HZ 5
> -#define BMA150_BW_1500HZ 6
>
> struct bma150_cfg {
> bool any_motion_int; /* Set to enable any-motion interrupt */
> --
> 2.17.1
>
