From: Jonathan Bakker <xc-racer2@xxxxxxx>
Add device tree bindings for Bosch BMA150 Accelerometer Sensor
Changes from v1:
- Add properties for all of bma150_cfg
- Correct IRQ type in example
Signed-off-by: Jonathan Bakker <xc-racer2@xxxxxxx>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@xxxxxxxxx>
---
.../bindings/input/bosch,bma150.txt | 38 +++++++++++++++++++
include/dt-bindings/input/bma150.h | 22 +++++++++++
include/linux/bma150.h | 13 +------
3 files changed, 62 insertions(+), 11 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/bosch,bma150.txt
create mode 100644 include/dt-bindings/input/bma150.h
diff --git a/Documentation/devicetree/bindings/input/bosch,bma150.txt b/Documentation/devicetree/bindings/input/bosch,bma150.txt
new file mode 100644
index 000000000000..f644d132f79c
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/bosch,bma150.txt
@@ -0,0 +1,38 @@
+* Bosch BMA150 Accelerometer Sensor
+
+Also works for the SMB380 and BMA023 accelerometers
+
+Required properties:
+- compatible : Should be "bosch,bma150"
+- reg : The I2C address of the sensor
+
+Optional properties:
+- interrupt-parent : should be the phandle for the interrupt controller
+- interrupts : Interrupt mapping for IRQ. If not present device will be polled
+- any-motion-int : bool for if the any motion interrupt should be enabled
+- hg-int : bool for if the high-G interrupt should be enabled
+- lg-int : bool for if the low-G interrupt should be enabled
+- any-motion-cfg : array of integers for any motion duration and threshold
+- hg-cfg : array of integers for high-G hysterisis, duration, and threshold
+- lg-cfg : array of integers for low-G hysterisis, duration, and threshold
+- range : configuration of range, one of BMA150_RANGE_* as defined in [1]
+- bandwidth : refresh rate of device, one of BMA150_BW_* as defined in [1]
+
+Example:
+
+bma150@38 {
+ compatible = "bosch,bma150";
+ reg = <0x38>;
+ interrupt-parent = <&gph0>;
+ interrupts = <1 IRQ_TYPE_EDGE_RISING>;
+ any-motion-int;
+ hg-int;
+ lg-int;
+ any-motion-cfg = <0 0>;
+ hg-cfg = <0 150 160>;
+ lg-cfg = <0 150 20>;
+ range = <BMA150_RANGE_2G>;
+ bandwidth = <BMA150_BW_50HZ>;
+};
+
+[1] include/dt-bindings/input/bma150.h
diff --git a/include/dt-bindings/input/bma150.h b/include/dt-bindings/input/bma150.h
new file mode 100644
index 000000000000..fb38ca787f0f
--- /dev/null
+++ b/include/dt-bindings/input/bma150.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides bindings for the BMA150 accelerometer
+ */
+#ifndef _DT_BINDINGS_INPUT_BMA150_H
+#define _DT_BINDINGS_INPUT_BMA150_H
+
+/* Range */
+#define BMA150_RANGE_2G 0
+#define BMA150_RANGE_4G 1
+#define BMA150_RANGE_8G 2
+
+/* Refresh rate */
+#define BMA150_BW_25HZ 0
+#define BMA150_BW_50HZ 1
+#define BMA150_BW_100HZ 2
+#define BMA150_BW_190HZ 3
+#define BMA150_BW_375HZ 4
+#define BMA150_BW_750HZ 5
+#define BMA150_BW_1500HZ 6
+
+#endif /* _DT_BINDINGS_INPUT_BMA150_H */
diff --git a/include/linux/bma150.h b/include/linux/bma150.h
index 97ade7cdc870..b85266a9c35c 100644
--- a/include/linux/bma150.h
+++ b/include/linux/bma150.h
@@ -20,19 +20,10 @@
#ifndef _BMA150_H_
#define _BMA150_H_
-#define BMA150_DRIVER "bma150"
+#include <dt-bindings/input/bma150.h>
-#define BMA150_RANGE_2G 0
-#define BMA150_RANGE_4G 1
-#define BMA150_RANGE_8G 2
+#define BMA150_DRIVER "bma150"
-#define BMA150_BW_25HZ 0
-#define BMA150_BW_50HZ 1
-#define BMA150_BW_100HZ 2
-#define BMA150_BW_190HZ 3
-#define BMA150_BW_375HZ 4
-#define BMA150_BW_750HZ 5
-#define BMA150_BW_1500HZ 6
struct bma150_cfg {
bool any_motion_int; /* Set to enable any-motion interrupt */
--
2.17.1
