Hello,
Thank you for your review.
On Thu, 19 Jul 2018 00:46:45 +0200
Ondřej Jirman <megous@xxxxxxxxxx> wrote:
> Hello Mylène,
>
> On Wed, Jul 18, 2018 at 08:27:17PM +0200, Mylène Josserand wrote:
> > Add the support of regulator to use it as VCC source.
> >
> > Signed-off-by: Mylène Josserand <mylene.josserand@xxxxxxxxxxx>
> > ---
> > .../bindings/input/touchscreen/edt-ft5x06.txt | 1 +
> > drivers/input/touchscreen/edt-ft5x06.c | 29 ++++++++++++++++++++++
> > 2 files changed, 30 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > index 025cf8c9324a..48e975b9c1aa 100644
> > --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > @@ -30,6 +30,7 @@ Required properties:
> > Optional properties:
> > - reset-gpios: GPIO specification for the RESET input
> > - wake-gpios: GPIO specification for the WAKE input
> > + - vcc-supply: Regulator that supplies the touchscreen
> >
> > - pinctrl-names: should be "default"
> > - pinctrl-0: a phandle pointing to the pin settings for the
> > diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> > index 1e18ca0d1b4e..aa94494b06b5 100644
> > --- a/drivers/input/touchscreen/edt-ft5x06.c
> > +++ b/drivers/input/touchscreen/edt-ft5x06.c
> > @@ -39,6 +39,7 @@
> > #include <linux/input/mt.h>
> > #include <linux/input/touchscreen.h>
> > #include <linux/of_device.h>
> > +#include <linux/regulator/consumer.h>
> >
> > #define WORK_REGISTER_THRESHOLD 0x00
> > #define WORK_REGISTER_REPORT_RATE 0x08
> > @@ -91,6 +92,7 @@ struct edt_ft5x06_ts_data {
> > struct touchscreen_properties prop;
> > u16 num_x;
> > u16 num_y;
> > + struct regulator *vcc;
> >
> > struct gpio_desc *reset_gpio;
> > struct gpio_desc *wake_gpio;
> > @@ -991,6 +993,22 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> >
> > tsdata->max_support_points = chip_data->max_support_points;
> >
> > + tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
> > + if (IS_ERR(tsdata->vcc)) {
> > + error = PTR_ERR(tsdata->vcc);
> > + if (error != -EPROBE_DEFER)
> > + dev_err(&client->dev, "failed to request regulator: %d\n",
> > + error);
> > + return error;
> > + }
> > +
> > + error = regulator_enable(tsdata->vcc);
> > + if (error < 0) {
> > + dev_err(&client->dev, "failed to enable vcc: %d\n",
> > + error);
> > + return error;
> > + }
> > +
> > tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
> > "reset", GPIOD_OUT_HIGH);
> > if (IS_ERR(tsdata->reset_gpio)) {
> > @@ -1120,20 +1138,31 @@ static int edt_ft5x06_ts_remove(struct i2c_client *client)
> > static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
> > {
> > struct i2c_client *client = to_i2c_client(dev);
> > + struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> >
> > if (device_may_wakeup(dev))
> > enable_irq_wake(client->irq);
> >
> > + regulator_disable(tsdata->vcc);
> > +
>
> How will the touchscreen wakeup the system with interrupt if you power it off
> on suspend? Perhaps guard this with device_may_wakeup() too?
True, thank you for pointing it out.
>
> > return 0;
> > }
> >
> > static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
> > {
> > struct i2c_client *client = to_i2c_client(dev);
> > + struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> > + int ret;
> >
> > if (device_may_wakeup(dev))
> > disable_irq_wake(client->irq);
> >
> > + ret = regulator_enable(tsdata->vcc);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to enable vcc: %d\n", ret);
> > + return ret;
> > + }
> > +
>
> Ditto.
ack
>
> Regards,
> o.
>
> > return 0;
> > }
> >
> > --
> > 2.11.0
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Best regards,
--
Mylène Josserand, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
