Hi, On 06/15/2016 01:27 AM, Rob Herring wrote:
On Mon, Jun 13, 2016 at 12:46:50PM +0200, Daniel Jansen wrote:From: Robert Dolca <robert.dolca@xxxxxxxxx> This driver adds support for Silead touchscreens. It has been tested with GSL1680 and GSL3680 touch panels. It supports ACPI and device tree enumeration. Screen resolution, the maximum number of fingers supported and firmware name are configurable. Signed-off-by: Robert Dolca <robert.dolca@xxxxxxxxx> Signed-off-by: Daniel Jansen <djaniboe@xxxxxxxxx> Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx> --- Changes since v3 - Check for the hw reporting more touches than expected - Fix input_mt_assign_slots usage - Remove unnecessary defines. - Shorten lines to be under 80 characters. - Move closing block comment to new line. - Add device tree bindings document for silead_gsl1680. - Use dev->driver->acpi_match_table instead of silead_ts_acpi_match - Replaced sprintf in default firmware file name generator with snprintf - Add missing input_mt_sync_frame() call - Fix device tree support Changes since v2 - removed device properties requirements - max x and y default to 4095 - max fingers default to 10 - firmware name uses the HID / device name - power named GPIO optional with fallback to indexed GPIO (without it there is no pm support in the driver) - finger tracking in the kernel using slot assignment - add device property for x/y inverting and xy swapping Changes since v1 - changed device tree properties names - removed cast for `void *id` - removed ifdef from suspend and resume and use __maybe_unused - remove ifdef from ACPI_PTR - renamed ret to error - removed input_set_capability for EV_ABS - fixed endianess issues - added mask for y in order to use only 12 bits - using the 4 MSb for touch ID instead of LSb (bug) - using the 4 LSB for X instead of MSb (bug) --- .../bindings/input/touchscreen/silead_gsl1680.txt | 39 ++ drivers/input/touchscreen/Kconfig | 13 + drivers/input/touchscreen/Makefile | 1 + drivers/input/touchscreen/silead.c | 652 +++++++++++++++++++++ 4 files changed, 705 insertions(+) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt create mode 100644 drivers/input/touchscreen/silead.c diff --git a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt new file mode 100644 index 0000000..d0164be --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt @@ -0,0 +1,39 @@ +* GSL 1680 touchscreen controller + +Required properties: +- compatible : "silead,gsl1680" +- reg : I2C slave address of the chip (0x40) +- interrupt-parent : a phandle pointing to the interrupt controller + serving the interrupt for this chip +- interrupts : interrupt specification for the gsl1680 interrupt +- wake-gpios : GPIO specification for the WAKE inputWhat direction is this?
This is an input to the touchscreen controller, it needs to be driven high to take the touchscreen controller out of its low power state. Regards, Hans
+- touchscreen-size-x : horizontal resolution of touchscreen (in pixels) +- touchscreen-size-y : vertical resolution of touchscreen (in pixels) +- touchscreen-max-fingers : maximal input values given to inputsystem + +Optional properties: +- touchscreen-inverted-x : X axis is inverted (boolean) +- touchscreen-inverted-y : Y axis is inverted (boolean) +- touchscreen-swapped-x-y : X and Y axis are swapped (boolean) + Swapping is done after inverting the axis + +Example: + +i2c@00000000 { + + gsl1680: touchscreen@40 { + compatible = "silead,gsl1680"; + reg = <0x40>; + interrupt-parent = <&pio>; + interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; + power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; + touchscreen-size-x = <480>; + touchscreen-size-y = <800>; + touchscreen-max-fingers = <5>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; + + /* ... */ +}; +
-- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
