On Mon, Jan 11, 2016 at 10:45:50AM -0800, Dmitry Torokhov wrote: > On Mon, Jan 11, 2016 at 06:54:23PM +0100, Oreste Salerno wrote: > > On Sun, Jan 10, 2016 at 09:01:56PM -0600, Rob Herring wrote: > > > On Sun, Jan 10, 2016 at 06:36:08PM +0100, Oreste Salerno wrote: > > > > Signed-off-by: Oreste Salerno <oreste.salerno@xxxxxxxxxx> > > > > --- > > > > .../bindings/input/touchscreen/cyttsp.txt | 82 +++++++++++++ > > > > drivers/input/touchscreen/cyttsp_core.c | 134 +++++++++++++++++++-- > > > > include/linux/input/cyttsp.h | 3 + > > > > 3 files changed, 212 insertions(+), 7 deletions(-) > > > > create mode 100644 Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt > > > > > > > > diff --git a/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt > > > > new file mode 100644 > > > > index 0000000..2dc5c65 > > > > --- /dev/null > > > > +++ b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt > > > > @@ -0,0 +1,82 @@ > > > > +* Cypress cyttsp touchscreen controller > > > > + > > > > +Required properties: > > > > +- compatible : must be "cypress,cyttsp-i2c" or "cypress,cyttsp-spi" > > > > +- reg : Device I2C address or SPI chip select number > > > > +- spi-max-frequency : Maximum SPI clocking speed of the device (for cyttsp-spi) > > > > +- interrupt-parent : the phandle for the gpio controller > > > > + (see interrupt binding[0]). > > > > +- interrupts : (gpio) interrupt to which the chip is connected > > > > + (see interrupt binding[0]). > > > > +- reset-gpios : the reset gpio the chip is connected to > > > > + (see GPIO binding[1] for more details). > > > > +- touchscreen-size-x : horizontal resolution of touchscreen (in pixels) > > > > +- touchscreen-size-y : vertical resolution of touchscreen (in pixels) > > > > +- bootloader-key : the 8-byte bootloader key that is required to switch > > > > + the chip from bootloader mode (default mode) to > > > > + application mode. > > > > + This property has to be specified as an array of 8 > > > > + '/bits/ 8' values. > > > > + > > > > +Optional properties: > > > > +- active-distance : the distance in pixels beyond which a touch must move > > > > + before movement is detected and reported by the device. > > > > + Valid values: 0-15. > > > > > > Wouldn't this be the same as touchscreen-fuzz-(x|y) which is the > > > replacement for the deprecated moving-threshold? > > > > > > > It is somewhat related. But I understand that the touchscreen-fuzz-(x|y) properties > > are meant to be used as parameters passed to input_set_abs_params(), which are used > > for a SW-based jitter filtering. > > The active-distance value instead is used to set a HW register in the chip which > > effectively performs the filtering in the HW. > > The driver is currently passing 0 as fuzz parameter to input_set_abs_params(). > > It doe snot have to and it will not if you use > touchscreen_parse_properties(). But you are right, fuzz is reserved for > software de-jittering, and it can be changed at any time from userspace > at input device level, but will not be communicated to the hardware. I > think hardware-based filtering is hardware-specific and I think > having a separate property is fine for it. We can still standardize on > name, units, etc though. > Yes, I looked at touchscreen_parse_properties and I was planning to use it as part of a future improvement patch. But it makes sense to introduce it in this patch already. > > > > > > +- active-interval-ms : the minimum period in ms between consecutive > > > > + scanning/processing cycles when the chip is in active mode. > > > > + Valid values: 0-255. > > > > +- lowpower-interval-ms : the minimum period in ms between consecutive > > > > + scanning/processing cycles when the chip is in low-power mode. > > > > + Valid values: 0-2550 > > > > +- touch-timeout-ms : minimum time in ms spent in the active power state while no > > > > + touches are detected before entering low-power mode. > > > > + Valid values: 0-2550 > > > > + > > > > > > Otherwise, looks fine. > > > > I am still waiting for a review from the driver maintainer (Ferruh Yigit), but I see > > that he hasn't been actively reviewing patches for the cyttsp* drivers for a while. > > I wonder what would be the process in this case? > > Please address the items from my other email and I should be able to > pick it up. > OK, I'll try to rework the patch soon and post a new version. Thanks a lot for your review! > Thanks. > > -- > Dmitry -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
