On Sun, Nov 15, 2015 at 05:20:47PM +0100, Sander Vermin wrote:
> Add support for rotating and inverted axis for the Sitronix ST1232 touchscreen controller.
>
> For the rotation of the touchscreen the devicetree resolution propteries are requierd. For this purpose the following devicetree mappings are implemented:
Fix the line wrap.
> - touchscreen-size-x
> - touchscreen-size-y
> - touchscreen-inverted-x
> - touchscreen-inverted-y
> - touchscreen-swapped-x-y
>
> Signed-off-by: Sander Vermin <sander@xxxxxxxxx>
> ---
> .../bindings/input/touchscreen/sitronix-st1232.txt | 18 +-
> drivers/input/touchscreen/st1232.c | 362 +++++++++++++++------
> 2 files changed, 272 insertions(+), 108 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt
> index 64ad48b..1dcd1b6 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt
> @@ -1,12 +1,18 @@
> * Sitronix st1232 touchscreen controller
>
> Required properties:
> -- compatible: must be "sitronix,st1232"
> -- reg: I2C address of the chip
> -- interrupts: interrupt to which the chip is connected
> +- compatible : must be "sitronix,st1232"
> +- reg : I2C address of the chip
> +- interrupts : interrupt to which the chip is connected
> +- touchscreen-size-x : horizontal resolution of touchscreen (in pixels)
> +- touchscreen-size-y : vertical resolution of touchscreen (in pixels)
> +
Reformatting in a separate patch please.
> Optional properties:
> -- gpios: a phandle to the reset GPIO
> +- gpios : a phandle to the reset GPIO
> +- touchscreen-inverted-x : X axis is inverted (boolean)
> +- touchscreen-inverted-y : Y axis is inverted (boolean)
> +- touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
>
> Example:
>
> @@ -18,6 +24,10 @@ Example:
> reg = <0x55>;
> interrupts = <2 0>;
> gpios = <&gpio1 166 0>;
> + touchscreen-size-y = <800>;
> + touchscreen-size-x = <480>;
> + touchscreen-inverted-y;
> + touchscreen-swapped-x-y;
> };
>
> /* ... */
> diff --git a/drivers/input/touchscreen/st1232.c b/drivers/input/touchscreen/st1232.c
> index e943678..0458a29 100644
> --- a/drivers/input/touchscreen/st1232.c
> +++ b/drivers/input/touchscreen/st1232.c
> @@ -1,6 +1,9 @@
> /*
> * ST1232 Touchscreen Controller Driver
> *
> + * Copyright (C) 2015 Sander Vermin
> + * Sander Vermin <sander@xxxxxxxxx>
> + *
> * Copyright (C) 2010 Renesas Solutions Corp.
> * Tony SIM <chinyeow.sim.xt@xxxxxxxxxxx>
> *
> @@ -22,6 +25,7 @@
> #include <linux/gpio.h>
> #include <linux/i2c.h>
> #include <linux/input.h>
> +#include <linux/input/mt.h>
> #include <linux/interrupt.h>
> #include <linux/module.h>
> #include <linux/of.h>
> @@ -31,70 +35,89 @@
> #include <linux/types.h>
> #include <linux/platform_data/st1232_pdata.h>
>
> -#define ST1232_TS_NAME "st1232-ts"
> +#define ST1232_REG_STATUS 0x01
> +#define ST1232_REG_CONTROL 0x02
> +#define ST1232_REG_XY_RES 0x04
> +#define ST1232_REG_TOUCHDATA 0x10
> +
> +#define ST1232_POWER_DOWN 0x02
>
> -#define MIN_X 0x00
> -#define MIN_Y 0x00
> -#define MAX_X 0x31f /* (800 - 1) */
> -#define MAX_Y 0x1df /* (480 - 1) */
> -#define MAX_AREA 0xff
> -#define MAX_FINGERS 2
> +#define ST1232_MAX_FINGERS 2
> +#define ST1232_MAX_RESOLUTION 800
> +#define ST1232_TS_NAME "st1232-ts"
>
> struct st1232_ts_finger {
> u16 x;
> u16 y;
> - u8 t;
> + u8 z;
> bool is_valid;
> };
>
> -struct st1232_ts_data {
> +struct st1232_touch_data {
> + __u8 softbutton;
> + __u8 finger_count;
> + struct st1232_ts_finger finger[ST1232_MAX_FINGERS];
> +};
> +
> +struct st1232_data {
> struct i2c_client *client;
> struct input_dev *input_dev;
> - struct st1232_ts_finger finger[MAX_FINGERS];
> struct dev_pm_qos_request low_latency_req;
> int reset_gpio;
> + u32 max_x;
> + u32 max_y;
> + bool invert_x;
> + bool invert_y;
> + bool swap_x_y;
> };
>
> -static int st1232_ts_read_data(struct st1232_ts_data *ts)
> +static int st1232_ts_read_data(struct i2c_client *client,
> + struct st1232_touch_data *touch_data)
> {
> - struct st1232_ts_finger *finger = ts->finger;
> - struct i2c_client *client = ts->client;
> - struct i2c_msg msg[2];
> int error;
> - u8 start_reg;
> + u8 start_reg = ST1232_REG_TOUCHDATA;
> u8 buf[10];
>
> - /* read touchscreen data from ST1232 */
> - msg[0].addr = client->addr;
> - msg[0].flags = 0;
> - msg[0].len = 1;
> - msg[0].buf = &start_reg;
> - start_reg = 0x10;
> -
> - msg[1].addr = ts->client->addr;
> - msg[1].flags = I2C_M_RD;
> - msg[1].len = sizeof(buf);
> - msg[1].buf = buf;
> + struct i2c_msg msg[2] = {
> + {
> + .addr = client->addr,
> + .len = 1,
> + .buf = &start_reg
> + },
> + {
> + .addr = client->addr,
> + .flags = I2C_M_RD,
> + .len = sizeof(buf),
> + .buf = (u8 *)buf
> + }
> + };
>
> error = i2c_transfer(client->adapter, msg, 2);
> if (error < 0)
> return error;
>
> + /* get number of fingers */
> + touch_data->finger_count = buf[0] & 0x7;
> +
> + /* get softkeys */
> + touch_data->softbutton = buf[1];
> +
> /* get "valid" bits */
> - finger[0].is_valid = buf[2] >> 7;
> - finger[1].is_valid = buf[5] >> 7;
> -
> - /* get xy coordinate */
> - if (finger[0].is_valid) {
> - finger[0].x = ((buf[2] & 0x0070) << 4) | buf[3];
> - finger[0].y = ((buf[2] & 0x0007) << 8) | buf[4];
> - finger[0].t = buf[8];
> + touch_data->finger[0].is_valid = buf[2] >> 7;
> + touch_data->finger[1].is_valid = buf[5] >> 7;
> +
> + /* get coordinate finger 0 */
> + if (touch_data->finger[0].is_valid) {
> + touch_data->finger[0].x = ((buf[2] & 0x70) << 4) | buf[3];
> + touch_data->finger[0].y = ((buf[2] & 0x07) << 8) | buf[4];
> + touch_data->finger[0].z = buf[8];
> }
>
> - if (finger[1].is_valid) {
> - finger[1].x = ((buf[5] & 0x0070) << 4) | buf[6];
> - finger[1].y = ((buf[5] & 0x0007) << 8) | buf[7];
> - finger[1].t = buf[9];
> + /* get coordinate finger 1 */
> + if (touch_data->finger[1].is_valid) {
> + touch_data->finger[1].x = ((buf[5] & 0x70) << 4) | buf[6];
> + touch_data->finger[1].y = ((buf[5] & 0x07) << 8) | buf[7];
> + touch_data->finger[1].z = buf[9];
> }
>
> return 0;
> @@ -102,59 +125,155 @@ static int st1232_ts_read_data(struct st1232_ts_data *ts)
>
> static irqreturn_t st1232_ts_irq_handler(int irq, void *dev_id)
> {
> - struct st1232_ts_data *ts = dev_id;
> - struct st1232_ts_finger *finger = ts->finger;
> + struct st1232_data *ts = dev_id;
> struct input_dev *input_dev = ts->input_dev;
> - int count = 0;
> + struct st1232_touch_data st_tdata;
> int i, ret;
>
> - ret = st1232_ts_read_data(ts);
> - if (ret < 0)
> - goto end;
> + ret = st1232_ts_read_data(ts->client, &st_tdata);
> + if (ret < 0) {
> + dev_err(dev_id, "Error reading touch data: %d\n", ret);
> + return IRQ_HANDLED;
> + }
> +
> + if (st_tdata.finger_count > ST1232_MAX_FINGERS) {
> + dev_warn(dev_id, "Too many fingers %d > %d\n",
> + st_tdata.finger_count, ST1232_MAX_FINGERS);
> + st_tdata.finger_count = ST1232_MAX_FINGERS;
> + }
>
> /* multi touch protocol */
> - for (i = 0; i < MAX_FINGERS; i++) {
> - if (!finger[i].is_valid)
> + for (i = 0; i < ST1232_MAX_FINGERS; i++) {
> + input_mt_slot(input_dev, i);
> + input_mt_report_slot_state(input_dev, MT_TOOL_FINGER,
> + st_tdata.finger[i].is_valid);
> + if (!st_tdata.finger[i].is_valid)
> continue;
>
> - input_report_abs(input_dev, ABS_MT_TOUCH_MAJOR, finger[i].t);
> - input_report_abs(input_dev, ABS_MT_POSITION_X, finger[i].x);
> - input_report_abs(input_dev, ABS_MT_POSITION_Y, finger[i].y);
> - input_mt_sync(input_dev);
> - count++;
> - }
> -
> - /* SYN_MT_REPORT only if no contact */
> - if (!count) {
> - input_mt_sync(input_dev);
> - if (ts->low_latency_req.dev) {
> - dev_pm_qos_remove_request(&ts->low_latency_req);
> - ts->low_latency_req.dev = NULL;
> + input_report_abs(input_dev, ABS_MT_PRESSURE,
> + st_tdata.finger[i].z);
> +
> + if (ts->invert_x)
> + st_tdata.finger[i].x = ts->max_x - st_tdata.finger[i].x;
> +
> + if (ts->invert_y)
> + st_tdata.finger[i].y = ts->max_y - st_tdata.finger[i].y;
> +
> + if (!ts->swap_x_y) {
> + input_event(input_dev, EV_ABS, ABS_MT_POSITION_X,
> + st_tdata.finger[i].x);
> + input_event(input_dev, EV_ABS, ABS_MT_POSITION_Y,
> + st_tdata.finger[i].y);
> + } else {
> + input_event(input_dev, EV_ABS, ABS_MT_POSITION_X,
> + st_tdata.finger[i].y);
> + input_event(input_dev, EV_ABS, ABS_MT_POSITION_Y,
> + st_tdata.finger[i].x);
> }
> - } else if (!ts->low_latency_req.dev) {
> - /* First contact, request 100 us latency. */
> - dev_pm_qos_add_ancestor_request(&ts->client->dev,
> - &ts->low_latency_req,
> - DEV_PM_QOS_RESUME_LATENCY, 100);
> }
>
> /* SYN_REPORT */
> + input_mt_sync_frame(input_dev);
> input_sync(input_dev);
>
> -end:
> return IRQ_HANDLED;
> }
>
> -static void st1232_ts_power(struct st1232_ts_data *ts, bool poweron)
> +static void st1232_ts_power(struct st1232_data *ts, bool poweron)
> {
> + /* only operates reset-pin */
> if (gpio_is_valid(ts->reset_gpio))
> gpio_direction_output(ts->reset_gpio, poweron);
> }
>
> +static int st1232_start(struct input_dev *dev)
> +{
> + struct st1232_data *data = input_get_drvdata(dev);
> + struct st1232_touch_data touch_data;
> + int error;
> + int count;
> +
> + u8 start_reg = ST1232_REG_XY_RES;
> + u8 buf[3];
> + /* set high nible of x and y resolution */
> + buf[0] = ((data->max_x >> 8) << 4) | (data->max_y >> 8);
> + /* set low byte of x resolution */
> + buf[1] = data->max_x;
> + /* set low byte of x resolution */
> + buf[2] = data->max_y;
> + struct i2c_msg msg[2] = {
> + {
> + .addr = data->client->addr,
> + .len = 1,
> + .buf = &start_reg
> + },
> + {
> + .addr = data->client->addr,
> + .flags = 0,
> + .len = sizeof(buf),
> + .buf = (u8 *)buf
> + }
> + };
> +
> + /* set reset-pin high */
> + st1232_ts_power(data, true);
> +
> + /* read status register, check for erros */
> + count = 0;
> + while (i2c_smbus_read_byte_data(data->client, ST1232_REG_STATUS) != 0) {
> + /* wait for the device to come up */
> + msleep(20);
> + count++;
> + if (count > 10) {
> + dev_err(&data->client->dev, "Device status Not OKE\n");
> + return -EINVAL;
> + }
> + }
> +
> + /* write 0 for defaults, disable powerdown */
> + i2c_smbus_write_byte_data(data->client, ST1232_REG_CONTROL, 0);
> +
> + /* write settings to controller */
> + error = i2c_transfer(data->client->adapter, msg, 2);
> + if (error < 0)
> + return error;
> +
> + /* read touch data to disgard possible interrupt */
> + error = st1232_ts_read_data(data->client, &touch_data);
> + if (error < 0)
> + return error;
> +
> + /* enable interrupt */
> + enable_irq(data->client->irq);
> +
> + dev_info(&data->client->dev, "Touchscreen device started\n");
> +
> + return 0;
> +}
> +
> +static void st1232_stop(struct input_dev *dev)
> +{
> + struct st1232_data *data = input_get_drvdata(dev);
> +
> + /* disable interrupt */
> + disable_irq(data->client->irq);
> +
> + /* write powerdown to touchscreen */
> + i2c_smbus_write_byte_data(data->client, ST1232_REG_CONTROL,
> + ST1232_POWER_DOWN);
> +
> + /* set reset-pin low */
> + st1232_ts_power(data, false);
> +
> + dev_info(&data->client->dev, "Touchscreen device stopped\n");
> +}
> +
> static int st1232_ts_probe(struct i2c_client *client,
> const struct i2c_device_id *id)
> {
> - struct st1232_ts_data *ts;
> + struct st1232_data *ts;
> + struct device *dev = &client->dev;
> + struct device_node *np = dev->of_node;
> struct st1232_pdata *pdata = dev_get_platdata(&client->dev);
> struct input_dev *input_dev;
> int error;
> @@ -177,8 +296,25 @@ static int st1232_ts_probe(struct i2c_client *client,
> if (!input_dev)
> return -ENOMEM;
>
> - ts->client = client;
> - ts->input_dev = input_dev;
> + if (of_property_read_u32(np, "touchscreen-size-x", &ts->max_x) ||
> + of_property_read_u32(np, "touchscreen-size-y", &ts->max_y)) {
> + dev_err(&client->dev,
> + "Error touchscreen-size-x and/or -y missing\n");
> + return -EINVAL;
> + }
> +
> + if (ts->max_x > ST1232_MAX_RESOLUTION ||
> + ts->max_y > ST1232_MAX_RESOLUTION) {
> + dev_err(&client->dev,
> + "Error touchscreen-size-x and/or -y exceding maximum of %d\n",
> + ST1232_MAX_RESOLUTION);
> + return -EINVAL;
> + }
> +
> + /* Optional device tree properties */
> + ts->swap_x_y = of_property_read_bool(np, "touchscreen-swapped-x-y");
> + ts->invert_x = of_property_read_bool(np, "touchscreen-inverted-x");
> + ts->invert_y = of_property_read_bool(np, "touchscreen-inverted-y");
>
> if (pdata)
> ts->reset_gpio = pdata->reset_gpio;
> @@ -197,30 +333,46 @@ static int st1232_ts_probe(struct i2c_client *client,
> }
> }
>
> - st1232_ts_power(ts, true);
> -
> - input_dev->name = "st1232-touchscreen";
> + input_dev->name = client->name;
> input_dev->id.bustype = BUS_I2C;
> - input_dev->dev.parent = &client->dev;
> + input_dev->open = st1232_start;
> + input_dev->close = st1232_stop;
> + input_dev->dev.parent = dev;
> +
> + if (!ts->swap_x_y) {
> + input_set_abs_params(input_dev, ABS_MT_POSITION_X, 0,
> + ts->max_x, 0, 0);
> + input_set_abs_params(input_dev, ABS_MT_POSITION_Y, 0,
> + ts->max_y, 0, 0);
> + } else {
> + input_set_abs_params(input_dev, ABS_MT_POSITION_X, 0,
> + ts->max_y, 0, 0);
> + input_set_abs_params(input_dev, ABS_MT_POSITION_Y, 0,
> + ts->max_x, 0, 0);
> + }
>
> - __set_bit(EV_SYN, input_dev->evbit);
> - __set_bit(EV_KEY, input_dev->evbit);
> - __set_bit(EV_ABS, input_dev->evbit);
> + error = input_mt_init_slots(input_dev, ST1232_MAX_FINGERS,
> + INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
> + if (error)
> + return error;
>
> - input_set_abs_params(input_dev, ABS_MT_TOUCH_MAJOR, 0, MAX_AREA, 0, 0);
> - input_set_abs_params(input_dev, ABS_MT_POSITION_X, MIN_X, MAX_X, 0, 0);
> - input_set_abs_params(input_dev, ABS_MT_POSITION_Y, MIN_Y, MAX_Y, 0, 0);
> + ts->client = client;
> + ts->input_dev = input_dev;
> + input_set_drvdata(input_dev, ts);
>
> error = devm_request_threaded_irq(&client->dev, client->irq,
> NULL, st1232_ts_irq_handler,
> IRQF_ONESHOT,
> client->name, ts);
> if (error) {
> - dev_err(&client->dev, "Failed to register interrupt\n");
> + dev_err(&client->dev, "Error requesting irq: %d\n", error);
> return error;
> }
>
> - error = input_register_device(ts->input_dev);
> + /* Stop device till opened */
> + st1232_stop(ts->input_dev);
> +
> + error = input_register_device(input_dev);
> if (error) {
> dev_err(&client->dev, "Unable to register %s input device\n",
> input_dev->name);
> @@ -228,6 +380,8 @@ static int st1232_ts_probe(struct i2c_client *client,
> }
>
> i2c_set_clientdata(client, ts);
> +
> + /* allow the device to wake */
> device_init_wakeup(&client->dev, 1);
>
> return 0;
> @@ -235,43 +389,43 @@ static int st1232_ts_probe(struct i2c_client *client,
>
> static int st1232_ts_remove(struct i2c_client *client)
> {
> - struct st1232_ts_data *ts = i2c_get_clientdata(client);
> + struct st1232_data *ts = i2c_get_clientdata(client);
>
> device_init_wakeup(&client->dev, 0);
> +
> + /* set reset-pin low */
> st1232_ts_power(ts, false);
>
> return 0;
> }
>
> -static int __maybe_unused st1232_ts_suspend(struct device *dev)
> +#ifdef CONFIG_PM_SLEEP
> +static int st1232_ts_suspend(struct device *dev)
> {
> struct i2c_client *client = to_i2c_client(dev);
> - struct st1232_ts_data *ts = i2c_get_clientdata(client);
> + struct st1232_data *data = i2c_get_clientdata(client);
>
> - if (device_may_wakeup(&client->dev)) {
> - enable_irq_wake(client->irq);
> - } else {
> - disable_irq(client->irq);
> - st1232_ts_power(ts, false);
> - }
> + mutex_lock(&data->input_dev->mutex);
> + if (data->input_dev->users)
> + st1232_stop(data->input_dev);
> + mutex_unlock(&data->input_dev->mutex);
>
> return 0;
> }
>
> -static int __maybe_unused st1232_ts_resume(struct device *dev)
> +static int st1232_ts_resume(struct device *dev)
> {
> struct i2c_client *client = to_i2c_client(dev);
> - struct st1232_ts_data *ts = i2c_get_clientdata(client);
> + struct st1232_data *data = i2c_get_clientdata(client);
>
> - if (device_may_wakeup(&client->dev)) {
> - disable_irq_wake(client->irq);
> - } else {
> - st1232_ts_power(ts, true);
> - enable_irq(client->irq);
> - }
> + mutex_lock(&data->input_dev->mutex);
> + if (data->input_dev->users)
> + st1232_start(data->input_dev);
> + mutex_unlock(&data->input_dev->mutex);
>
> return 0;
> }
> +#endif
>
> static SIMPLE_DEV_PM_OPS(st1232_ts_pm_ops,
> st1232_ts_suspend, st1232_ts_resume);
> @@ -282,13 +436,12 @@ static const struct i2c_device_id st1232_ts_id[] = {
> };
> MODULE_DEVICE_TABLE(i2c, st1232_ts_id);
>
> -#ifdef CONFIG_OF
> -static const struct of_device_id st1232_ts_dt_ids[] = {
> +static const struct of_device_id st1232_of_match[] = {
> { .compatible = "sitronix,st1232", },
> { }
> };
> -MODULE_DEVICE_TABLE(of, st1232_ts_dt_ids);
> -#endif
> +MODULE_DEVICE_TABLE(of, st1232_of_match);
> +
>
> static struct i2c_driver st1232_ts_driver = {
> .probe = st1232_ts_probe,
> @@ -296,13 +449,14 @@ static struct i2c_driver st1232_ts_driver = {
> .id_table = st1232_ts_id,
> .driver = {
> .name = ST1232_TS_NAME,
> - .of_match_table = of_match_ptr(st1232_ts_dt_ids),
> + .owner = THIS_MODULE,
> + .of_match_table = st1232_of_match,
> .pm = &st1232_ts_pm_ops,
> },
> };
>
> module_i2c_driver(st1232_ts_driver);
>
> -MODULE_AUTHOR("Tony SIM <chinyeow.sim.xt@xxxxxxxxxxx>");
> +MODULE_AUTHOR("Tony SIM <chinyeow.sim.xt@xxxxxxxxxxx>, Sander Vermin <sander@xxxxxxxxx>");
> MODULE_DESCRIPTION("SITRONIX ST1232 Touchscreen Controller Driver");
> MODULE_LICENSE("GPL");
> --
> 2.5.0
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
