On Mon, 7 Sep 2015 17:36:17 +0300
Irina Tirdea <irina.tirdea@xxxxxxxxx> wrote:
> After power on, it is recommended that the driver resets the device.
> The reset procedure timing is described in the datasheet and is used
> at device init (before writing device configuration) and
> for power management. It is a sequence of setting the interrupt
> and reset pins high/low at specific timing intervals. This procedure
> also includes setting the slave address to the one specified in the
> ACPI/device tree.
>
> This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
> driver gt9xx.c for Android (publicly available in Android kernel
> trees for various devices).
>
> For reset the driver needs to control the interrupt and
> reset gpio pins (configured through ACPI/device tree). For devices
> that do not have the gpio pins declared, the functionality depending
> on these pins will not be available, but the device can still be used
> with basic functionality.
>
> Signed-off-by: Octavian Purdila <octavian.purdila@xxxxxxxxx>
> Signed-off-by: Irina Tirdea <irina.tirdea@xxxxxxxxx>
> ---
> .../bindings/input/touchscreen/goodix.txt | 5 +
> drivers/input/touchscreen/goodix.c | 136 +++++++++++++++++++++
> 2 files changed, 141 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
> index 8ba98ee..c0715f8 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
> @@ -12,6 +12,8 @@ Required properties:
> - reg : I2C address of the chip. Should be 0x5d or 0x14
> - interrupt-parent : Interrupt controller to which the chip is connected
> - interrupts : Interrupt to which the chip is connected
> + - gpios : GPIOS the chip is connected to: first one is the
> + interrupt gpio and second one the reset gpio.
>
> Example:
>
> @@ -23,6 +25,9 @@ Example:
> reg = <0x5d>;
> interrupt-parent = <&gpio>;
> interrupts = <0 0>;
> +
> + gpios = <&gpio1 0 0>, /* INT */
> + <&gpio1 1 0>; /* RST */
> };
>
> /* ... */
> diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
> index 7be6eab..8edfc06 100644
> --- a/drivers/input/touchscreen/goodix.c
> +++ b/drivers/input/touchscreen/goodix.c
> @@ -17,6 +17,7 @@
> #include <linux/acpi.h>
> #include <linux/delay.h>
> #include <linux/dmi.h>
> +#include <linux/gpio.h>
> #include <linux/i2c.h>
> #include <linux/input.h>
> #include <linux/input/mt.h>
> @@ -37,6 +38,8 @@ struct goodix_ts_data {
> unsigned int int_trigger_type;
> bool rotated_screen;
> int cfg_len;
> + struct gpio_desc *gpiod_int;
> + struct gpio_desc *gpiod_rst;
> };
>
> #define GOODIX_MAX_HEIGHT 4096
> @@ -89,6 +92,30 @@ static const struct dmi_system_id rotated_screen[] = {
> {}
> };
>
> +/*
> + * ACPI table specifies gpio pins in this order: first rst pin and
> + * then interrupt pin.
> + */
> +static const struct dmi_system_id goodix_rst_pin_first[] = {
> +#if defined(CONFIG_DMI) && defined(CONFIG_X86)
> + {
> + .ident = "WinBook TW100",
> + .matches = {
> + DMI_MATCH(DMI_SYS_VENDOR, "WinBook"),
> + DMI_MATCH(DMI_PRODUCT_NAME, "TW100")
> + }
> + },
> + {
> + .ident = "WinBook TW700",
> + .matches = {
> + DMI_MATCH(DMI_SYS_VENDOR, "WinBook"),
> + DMI_MATCH(DMI_PRODUCT_NAME, "TW700")
> + },
> + },
> +#endif
> + {}
> +};
> +
> /**
> * goodix_i2c_read - read data from a register of the i2c slave device.
> *
> @@ -237,6 +264,102 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
> return IRQ_HANDLED;
> }
>
> +static int goodix_int_sync(struct goodix_ts_data *ts)
> +{
> + int error;
> +
> + error = gpiod_direction_output(ts->gpiod_int, 0);
> + if (error)
> + return error;
> + msleep(50); /* T5: 50ms */
> +
> + return gpiod_direction_input(ts->gpiod_int);
> +}
> +
> +/**
> + * goodix_reset - Reset device during power on
> + *
> + * @ts: goodix_ts_data pointer
> + */
> +static int goodix_reset(struct goodix_ts_data *ts)
> +{
> + int error;
> +
> + /* begin select I2C slave addr */
> + error = gpiod_direction_output(ts->gpiod_rst, 0);
> + if (error)
> + return error;
> + msleep(20); /* T2: > 10ms */
> + /* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
> + error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
> + if (error)
> + return error;
> + usleep_range(100, 2000); /* T3: > 100us */
> + error = gpiod_direction_output(ts->gpiod_rst, 1);
> + if (error)
> + return error;
> + usleep_range(6000, 10000); /* T4: > 5ms */
> + /* end select I2C slave addr */
> + error = gpiod_direction_input(ts->gpiod_rst);
> + if (error)
> + return error;
> + return goodix_int_sync(ts);
> +}
> +
> +/**
> + * goodix_get_gpio_config - Get GPIO config from ACPI/DT
> + *
> + * @ts: goodix_ts_data pointer
> + */
> +static int goodix_get_gpio_config(struct goodix_ts_data *ts,
> + const struct i2c_device_id *i2c_id)
> +{
> + int error;
> + struct device *dev;
> + struct gpio_desc *gpiod;
> + /* Default gpio pin order: irq, rst */
> + int irq_idx = 0, rst_idx = 1;
> +
> + if (!ts->client)
> + return -EINVAL;
> + dev = &ts->client->dev;
> +
> + if (dmi_check_system(goodix_rst_pin_first)) {
> + dev_dbg(&ts->client->dev,
> + "Applying 'reverse gpio pin order' quirk\n");
> + rst_idx = 0;
> + irq_idx = 1;
> + }
> +
> + /* Get interrupt GPIO pin number */
> + gpiod = devm_gpiod_get_index(dev, NULL, irq_idx, GPIOD_IN);
> + if (IS_ERR(gpiod)) {
> + error = PTR_ERR(gpiod);
> + if (error != -EPROBE_DEFER)
> + dev_warn(dev, "Failed to get GPIO %d: %d\n",
> + irq_idx, error);
> + if (error == -ENOENT)
> + return 0;
> + return error;
> + }
> + ts->gpiod_int = gpiod;
> +
> + /* Get the reset line GPIO pin number */
> + gpiod = devm_gpiod_get_index(dev, NULL, rst_idx, GPIOD_IN);
> + if (IS_ERR(gpiod)) {
> + error = PTR_ERR(gpiod);
> + if (error != -EPROBE_DEFER)
> + dev_warn(dev, "Failed to get GPIO %d: %d\n",
> + rst_idx, error);
> + if (error == -ENOENT)
> + return 0;
> + return error;
> + }
> + ts->gpiod_rst = gpiod;
> +
> + return 0;
> +}
> +
> /**
> * goodix_read_config - Read the embedded configuration of the panel
> *
> @@ -419,6 +542,19 @@ static int goodix_ts_probe(struct i2c_client *client,
>
> ts->cfg_len = goodix_get_cfg_len(id_info);
>
> + error = goodix_get_gpio_config(ts, id);
> + if (error)
> + return error;
> +
> + if (ts->gpiod_int && ts->gpiod_rst) {
> + /* reset the controller */
> + error = goodix_reset(ts);
> + if (error) {
> + dev_err(&client->dev, "Controller reset failed.\n");
> + return error;
> + }
> + }
> +
On devices with devicetree, such as ARM tablets, we can set I2C address via DT, so driver should reset controller and set right address.
If we don't do this we get "I2C communication failure: -6".
Also, most of touchscreen drivers tries to reset controllers before start communicating, so we need do the same.
> goodix_read_config(ts);
>
> error = goodix_request_input_dev(ts, version_info, id_info);
> --
> 1.9.1
>
--
Thanks and regards,
Aleksei Mamlin
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
