Am Donnerstag, 19. Dezember 2024, 20:51:41 CET schrieb Kees Bakker:
> Op 19-12-2024 om 20:43 schreef Heiko Stübner:
> > Hi Kees,
> >
> > Am Donnerstag, 19. Dezember 2024, 20:18:38 CET schrieb Kees Bakker:
> >> Op 07-11-2024 om 12:47 schreef Heiko Stuebner:
> >>> These microcontroller units are used in network-attached-storage devices
> >>> made by QNAP and provide additional functionality to the system.
> >>>
> >>> This adds the base driver that implements the serial protocol via
> >>> serdev and additionally hooks into the poweroff handlers to turn
> >>> off the parts of the system not supplied by the general PMIC.
> >>>
> >>> Turning off (at least the TSx33 devices using Rockchip SoCs) consists of
> >>> two separate actions. Turning off the MCU alone does not turn off the main
> >>> SoC and turning off only the SoC/PMIC does not turn off the hard-drives.
> >>> Also if the MCU is not turned off, the system also won't start again until
> >>> it is unplugged from power.
> >>>
> >>> So on shutdown the MCU needs to be turned off separately before the
> >>> main PMIC.
> >>>
> >>> The protocol spoken by the MCU is sadly not documented, but was
> >>> obtained by listening to the chatter on the serial port, as thankfully
> >>> the "hal_app" program from QNAPs firmware allows triggering all/most
> >>> MCU actions from the command line.
> >>>
> >>> The implementation of how to talk to the serial device got some
> >>> inspiration from the rave-sp servdev driver.
> >>>
> >>> Signed-off-by: Heiko Stuebner <heiko@xxxxxxxxx>
> >>> ---
> >>> MAINTAINERS | 6 +
> >>> drivers/mfd/Kconfig | 13 ++
> >>> drivers/mfd/Makefile | 2 +
> >>> drivers/mfd/qnap-mcu.c | 338 +++++++++++++++++++++++++++++++++++
> >>> include/linux/mfd/qnap-mcu.h | 26 +++
> >>> 5 files changed, 385 insertions(+)
> >>> create mode 100644 drivers/mfd/qnap-mcu.c
> >>> create mode 100644 include/linux/mfd/qnap-mcu.h
> >>>
> >>> [...]
> >>> diff --git a/drivers/mfd/qnap-mcu.c b/drivers/mfd/qnap-mcu.c
> >>> new file mode 100644
> >>> index 000000000000..4be39d8b2905
> >>> --- /dev/null
> >>> +++ b/drivers/mfd/qnap-mcu.c
> >>> [...]
> >>> +int qnap_mcu_exec(struct qnap_mcu *mcu,
> >>> + const u8 *cmd_data, size_t cmd_data_size,
> >>> + u8 *reply_data, size_t reply_data_size)
> >>> +{
> >>> + unsigned char rx[QNAP_MCU_RX_BUFFER_SIZE];
> >>> + size_t length = reply_data_size + QNAP_MCU_CHECKSUM_SIZE;
> >>> + struct qnap_mcu_reply *reply = &mcu->reply;
> >>> + int ret = 0;
> >>> +
> >>> + if (length > sizeof(rx)) {
> >>> + dev_err(&mcu->serdev->dev, "expected data too big for receive buffer");
> >>> + return -EINVAL;
> >>> + }
> >>> +
> >>> + mutex_lock(&mcu->bus_lock);
> >>> +
> >>> + reply->data = rx,
> >>> + reply->length = length,
> >>> + reply->received = 0,
> >>> + reinit_completion(&reply->done);
> >>> +
> >>> + qnap_mcu_write(mcu, cmd_data, cmd_data_size);
> >>> +
> >>> + serdev_device_wait_until_sent(mcu->serdev, msecs_to_jiffies(QNAP_MCU_TIMEOUT_MS));
> >>> +
> >>> + if (!wait_for_completion_timeout(&reply->done, msecs_to_jiffies(QNAP_MCU_TIMEOUT_MS))) {
> >>> + dev_err(&mcu->serdev->dev, "Command timeout\n");
> >>> + ret = -ETIMEDOUT;
> >>> + } else {
> >>> + u8 crc = qnap_mcu_csum(rx, reply_data_size);
> >> Here `rx` is still not initialized.
> > The MCU works in a way that a sent command always causes "reply_data_size"
> > bytes to be returned.
> >
> > So for each qnap_mcu_write() above we know that this amount of bytes has
> > been returned (and thus written into rx) if the completion above finishes
> > sucessfully.
> >
> > "rx" is assigned to reply->data above (same as the expected received size).
> > When characters are received on the serial line, this will trigger
> > qnap_mcu_receive_buf() from the serdev and thus fill those elements in rx.
> >
> > So if we land at the qnap_mcu_csum() call, we do have received the expected
> > amount of bytes from the serdev and thus rx is filled accordingly.
> >
> > If we don't receive the needed amount of bytes, we end up in the timeout
> > above that.
> >
> > What did I miss?
> Sorry, my fault. I missed the essential part of the external event (external
> for this function that is).
> Thanks for explaining.
no worries :-) .
The more eyes, the better.
Heiko
