On 11/28/24 6:55 AM, Alisa-Dariana Roman wrote:
> Add support for the SYNC pin GPIO specification in the devicetree
> bindings. This pin allows synchronization of digital filters and analog
> modulators when using multiple devices. Update the examples to
> demonstrate the usage of the new property.
>
> Also update the interrupt type in the examples to use the proper
> IRQ_TYPE_EDGE_FALLING macro instead of the raw value.
>
> Signed-off-by: Alisa-Dariana Roman <alisa.roman@xxxxxxxxxx>
> ---
> .../bindings/iio/adc/adi,ad7192.yaml | 19 +++++++++++++++++--
> 1 file changed, 17 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml
> index f70caefdace7..1cd0fd13bc42 100644
> --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml
> @@ -59,6 +59,17 @@ properties:
> interrupts:
> maxItems: 1
>
> + sync-gpios:
> + description: |
> + Optional GPIO spec for the SYNC pin. The SYNC pin allows synchronization
> + of the digital filters and analog modulators when using multiple AD7192
> + devices. When SYNC is pulled low, it resets the digital filter nodes,
> + filter control logic, calibration control logic, and holds the analog
> + modulator in reset state. Only specify this property if you need to
> + actively control SYNC for multi-device synchronization, otherwise it
> + defaults to HIGH.
The datasheet says that the /SYNC pin can also be used to trigger a conversion.
But I'm not sure we really need all this explanation here. The important parts
are that this is a GPIO that is connected to the /SYNC pin and in the
synchronization use case, the same GPIO might be connected to multiple ADC
chips.
> + maxItems: 1
> +
> aincom-supply:
> description: |
> AINCOM voltage supply. Analog inputs AINx are referenced to this input
> @@ -182,6 +193,8 @@ unevaluatedProperties: false
>
> examples:
> - |
> + #include <dt-bindings/gpio/gpio.h>
> + #include <dt-bindings/interrupt-controller/irq.h>
> spi {
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -194,8 +207,9 @@ examples:
> spi-cpha;
> clocks = <&ad7192_mclk>;
> clock-names = "mclk";
> - interrupts = <25 0x2>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> interrupt-parent = <&gpio>;
> + sync-gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
On the schematic, the SYNC pin is marked as active low, so I would
expect GPIO_ACTIVE_LOW here.
> aincom-supply = <&aincom>;
> dvdd-supply = <&dvdd>;
> avdd-supply = <&avdd>;
> @@ -208,6 +222,7 @@ examples:
> };
> };
> - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> spi {
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -223,7 +238,7 @@ examples:
> spi-cpol;
> spi-cpha;
> #clock-cells = <0>;
> - interrupts = <25 0x2>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> interrupt-parent = <&gpio>;
> aincom-supply = <&aincom>;
> dvdd-supply = <&dvdd>;
