Re: [PATCH v6 5/8] iio: dac: ad3552r: changes to use FIELD_PREP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 10/14/24 5:08 AM, Angelo Dureghello wrote:
> From: Angelo Dureghello <adureghello@xxxxxxxxxxxx>
> 
> Changes to use FIELD_PREP, so that driver-specific ad3552r_field_prep
> is removed. Variables (arrays) that was used to call ad3552r_field_prep
> are removed too.
> 
> Signed-off-by: Angelo Dureghello <adureghello@xxxxxxxxxxxx>
> ---

Found one likely bug. The rest are suggestions to keep the static
analyzers happy.

				\
> @@ -510,8 +416,14 @@ static int ad3552r_write_raw(struct iio_dev *indio_dev,
>  					val);
>  		break;
>  	case IIO_CHAN_INFO_ENABLE:
> -		err = ad3552r_set_ch_value(dac, AD3552R_CH_DAC_POWERDOWN,
> -					   chan->channel, !val);
> +		if (chan->channel == 0)
> +			val = FIELD_PREP(AD3552R_MASK_CH_DAC_POWERDOWN(0), !val);
> +		else
> +			val = FIELD_PREP(AD3552R_MASK_CH_DAC_POWERDOWN(1), !val);

In the past, I've had bots (Sparse, IIRC) complain about using !val
with FIELD_PREP. Alternative is to write it as val ? 1 : 0.

> +
> +		err = ad3552r_update_reg_field(dac, AD3552R_REG_ADDR_POWERDOWN_CONFIG,
> +					       AD3552R_MASK_CH_DAC_POWERDOWN(chan->channel),
> +					       val);
>  		break;
>  	default:
>  		err = -EINVAL;
> @@ -715,9 +627,9 @@ static int ad3552r_reset(struct ad3552r_desc *dac)
>  	}
>  
>  	return ad3552r_update_reg_field(dac,
> -					addr_mask_map[AD3552R_ADDR_ASCENSION][0],
> -					addr_mask_map[AD3552R_ADDR_ASCENSION][1],
> -					val);
> +					AD3552R_REG_ADDR_INTERFACE_CONFIG_A,
> +					AD3552R_MASK_ADDR_ASCENSION,
> +					FIELD_PREP(AD3552R_MASK_ADDR_ASCENSION, val));
>  }
>  
>  static void ad3552r_get_custom_range(struct ad3552r_desc *dac, s32 i, s32 *v_min,
> @@ -812,20 +724,20 @@ static int ad3552r_configure_custom_gain(struct ad3552r_desc *dac,
>  				     "mandatory custom-output-range-config property missing\n");
>  
>  	dac->ch_data[ch].range_override = 1;
> -	reg |= ad3552r_field_prep(1, AD3552R_MASK_CH_RANGE_OVERRIDE);
> +	reg |= FIELD_PREP(AD3552R_MASK_CH_RANGE_OVERRIDE, 1);
>  
>  	err = fwnode_property_read_u32(gain_child, "adi,gain-scaling-p", &val);
>  	if (err)
>  		return dev_err_probe(dev, err,
>  				     "mandatory adi,gain-scaling-p property missing\n");
> -	reg |= ad3552r_field_prep(val, AD3552R_MASK_CH_GAIN_SCALING_P);
> +	reg |= FIELD_PREP(AD3552R_MASK_CH_GAIN_SCALING_P, val);
>  	dac->ch_data[ch].p = val;
>  
>  	err = fwnode_property_read_u32(gain_child, "adi,gain-scaling-n", &val);
>  	if (err)
>  		return dev_err_probe(dev, err,
>  				     "mandatory adi,gain-scaling-n property missing\n");
> -	reg |= ad3552r_field_prep(val, AD3552R_MASK_CH_GAIN_SCALING_N);
> +	reg |= FIELD_PREP(AD3552R_MASK_CH_GAIN_SCALING_N, val);
>  	dac->ch_data[ch].n = val;
>  
>  	err = fwnode_property_read_u32(gain_child, "adi,rfb-ohms", &val);
> @@ -841,9 +753,9 @@ static int ad3552r_configure_custom_gain(struct ad3552r_desc *dac,
>  	dac->ch_data[ch].gain_offset = val;
>  
>  	offset = abs((s32)val);
> -	reg |= ad3552r_field_prep((offset >> 8), AD3552R_MASK_CH_OFFSET_BIT_8);
> +	reg |= FIELD_PREP(AD3552R_MASK_CH_OFFSET_BIT_8, (offset >> 8));

Can drop () from (offset >> 8).

>  
> -	reg |= ad3552r_field_prep((s32)val < 0, AD3552R_MASK_CH_OFFSET_POLARITY);
> +	reg |= FIELD_PREP(AD3552R_MASK_CH_OFFSET_POLARITY, (s32)val < 0);

Instead of (s32) cast, could write val < 0 : 1 : 0 (to be consistent with
suggestion above for replacing !val).

>  	addr = AD3552R_REG_ADDR_CH_GAIN(ch);
>  	err = ad3552r_write_reg(dac, addr,
>  				offset & AD3552R_MASK_CH_OFFSET_BITS_0_7);
> @@ -886,9 +798,9 @@ static int ad3552r_configure_device(struct ad3552r_desc *dac)
>  	}
>  
>  	err = ad3552r_update_reg_field(dac,
> -				       addr_mask_map[AD3552R_VREF_SELECT][0],
> -				       addr_mask_map[AD3552R_VREF_SELECT][1],
> -				       val);
> +				       AD3552R_REG_ADDR_SH_REFERENCE_CONFIG,
> +				       AD3552R_MASK_REFERENCE_VOLTAGE_SEL,
> +				       FIELD_PREP(AD3552R_MASK_REFERENCE_VOLTAGE_SEL, val));
>  	if (err)
>  		return err;
>  
> @@ -900,9 +812,9 @@ static int ad3552r_configure_device(struct ad3552r_desc *dac)
>  		}
>  
>  		err = ad3552r_update_reg_field(dac,
> -					       addr_mask_map[AD3552R_SDO_DRIVE_STRENGTH][0],
> -					       addr_mask_map[AD3552R_SDO_DRIVE_STRENGTH][1],
> -					       val);
> +					       AD3552R_REG_ADDR_INTERFACE_CONFIG_D,
> +					       AD3552R_MASK_SDO_DRIVE_STRENGTH,
> +					       FIELD_PREP(AD3552R_MASK_SDO_DRIVE_STRENGTH, val));
>  		if (err)
>  			return err;
>  	}
> @@ -938,9 +850,15 @@ static int ad3552r_configure_device(struct ad3552r_desc *dac)
>  						     "Invalid adi,output-range-microvolt value\n");
>  
>  			val = err;
> -			err = ad3552r_set_ch_value(dac,
> -						   AD3552R_CH_OUTPUT_RANGE_SEL,
> -						   ch, val);
> +			if (ch == 0)
> +				val = FIELD_PREP(AD3552R_MASK_CH_OUTPUT_RANGE_SEL(0), val);
> +			else
> +				val = FIELD_PREP(AD3552R_MASK_CH_OUTPUT_RANGE_SEL(1), val);
> +
> +			err = ad3552r_update_reg_field(dac,
> +						       AD3552R_REG_ADDR_CH0_CH1_OUTPUT_RANGE,
> +						       AD3552R_MASK_CH_OUTPUT_RANGE_SEL(ch),
> +						       val);
>  			if (err)
>  				return err;
>  
> @@ -958,7 +876,14 @@ static int ad3552r_configure_device(struct ad3552r_desc *dac)
>  		ad3552r_calc_gain_and_offset(dac, ch);
>  		dac->enabled_ch |= BIT(ch);
>  
> -		err = ad3552r_set_ch_value(dac, AD3552R_CH_SELECT, ch, 1);
> +		if (ch == 0)
> +			val = FIELD_PREP(AD3552R_MASK_CH(0), 1);
> +		else
> +			val = FIELD_PREP(AD3552R_MASK_CH(1), 1);
> +
> +		err = ad3552r_update_reg_field(dac,
> +					       AD3552R_REG_ADDR_CH_SELECT_16B,
> +					       AD3552R_MASK_CH(ch), val);
>  		if (err < 0)
>  			return err;
>  
> @@ -970,8 +895,15 @@ static int ad3552r_configure_device(struct ad3552r_desc *dac)
>  	/* Disable unused channels */
>  	for_each_clear_bit(ch, &dac->enabled_ch,
>  			   dac->model_data->num_hw_channels) {
> -		err = ad3552r_set_ch_value(dac, AD3552R_CH_AMPLIFIER_POWERDOWN,
> -					   ch, 1);
> +		if (ch == 0)
> +			val = FIELD_PREP(AD3552R_MASK_CH_OUTPUT_RANGE_SEL(0), 1);
> +		else
> +			val = FIELD_PREP(AD3552R_MASK_CH_OUTPUT_RANGE_SEL(1), 1);

Should these be AD3552R_MASK_CH_AMPLIFIER_POWERDOWN instead of
AD3552R_MASK_CH_OUTPUT_RANGE_SEL? (2 above and 1 below.)

> +
> +		err = ad3552r_update_reg_field(dac,
> +					       AD3552R_REG_ADDR_POWERDOWN_CONFIG,
> +					       AD3552R_MASK_CH_OUTPUT_RANGE_SEL(ch),
> +					       val);
>  		if (err)
>  			return err;
>  	}
> 





[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux