This series aims to add iio backend support for AD7606X ADCs. In a nutshell, iio backend is a paradigm to shift the logic establishing the connexion between iio buffers and backend buffers into the backend's driver. This provides a more stable programming interface to the driver developers, and give more flexibility in the way the hardware communicates. The support will be first added on AD7606B, and on next patches AD7606C16 and AD7606C18 will be added. The series have been tested on a Zedboard, using the latest HDL available, i.e https://github.com/analogdevicesinc/hdl/commit/7d0a4cee1b5fa403f175af513d7eb804c3bd75d0 and an AD7606B FMCZ EKV. This HDL handles both the conversion trigger (through a PWM), and the end of conversion interruption, and is compatible with axi-adc, which is "iio-backendable". More information about this HDL design can be found at: https://wiki.analog.com/resources/eval/user-guides/ad7606x-fmc/hdl The support is thus separated in two parts: - PWM support was first added. My first intention was to make it available for any version of the driver, but the time required to handle the interruption is not neglectable, and I saw drifts that would eventually cause an overlapping SPI read with a new conversion trigger, whith catastrphic consequences. To mitigate this, CRC check must be implemented, but indeed increasing the samplerate causes more sample to be lost. Therefore, I decided to only allow PWM for iio-backend powered device as a first intention, leaving open the possibility to add the general compatibility afterwards. - IIO backend support was added: Once the PWM support was ready, the driver can be extended to iio-backend. The iio-backend powered version of the driver is a platform driver, and an exemple devicetree node is available in the bindings. The following features will be added in subsequent patch series: - software mode for iio backend - 18 bits mode (AD7606C18) - single read (IIO_CHAN_READ_RAW) Signed-off-by: Guillaume Stols <gstols@xxxxxxxxxxxx> --- Changes in v2: - Logical change in dt-bindings, using a flag for the interface instead of infering it from the value of the "reg" property. - Removal of get_platform_match_data addition, instead the logic is directly used in the file. - Removal of use and export of pwm_get_state_hw, returning the configured frequency instead of the running one. - Correction on various typos, whitespaces, bad order of includes. - Separation of SPI conditions and PWM disabling for no backend in other commits. - Link to v1: https://lore.kernel.org/r/20240815-ad7606_add_iio_backend_support-v1-0-cea3e11b1aa4@xxxxxxxxxxxx --- Guillaume Stols (10): dt-bindings: iio: adc: ad7606: Set the correct polarity dt-bindings: iio: adc: ad7606: Make corrections on spi conditions dt-bindings: iio: adc: ad7606: Add iio backend bindings Documentation: iio: Document ad7606 driver iio: adc: ad7606: Sort includes in alphabetical order iio: adc: ad7606: Add PWM support for conversion trigger iio: adc: ad7606: Add compatibility to fw_nodes iio: adc: ad7606: Fix typo in the driver name iio: adc: ad7606: Add iio-backend support iio: adc: ad7606: Disable PWM usage for non backend version .../devicetree/bindings/iio/adc/adi,ad7606.yaml | 97 ++++- Documentation/iio/ad7606.rst | 143 +++++++ drivers/iio/adc/Kconfig | 4 +- drivers/iio/adc/ad7606.c | 474 +++++++++++++++------ drivers/iio/adc/ad7606.h | 51 ++- drivers/iio/adc/ad7606_par.c | 126 +++++- drivers/iio/adc/ad7606_spi.c | 33 +- 7 files changed, 749 insertions(+), 179 deletions(-) --- base-commit: 8bea3878a1511bceadc2fbf284b00bcc5a2ef28d change-id: 20240725-ad7606_add_iio_backend_support-c401305a6924 Best regards, -- Guillaume Stols <gstols@xxxxxxxxxxxx>
