[no subject]

Specific comments inline.

Jonathan

> ---
>  .../iio/proximity/everlight,pm16d17.yaml      | 95 +++++++++++++++++++
>  1 file changed, 95 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/proximity/everlight,pm16d17.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/proximity/everlight,pm16d17.yaml b/Documentation/devicetree/bindings/iio/proximity/everlight,pm16d17.yaml
> new file mode 100644
> index 000000000000..fadc3075181a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/proximity/everlight,pm16d17.yaml
> @@ -0,0 +1,95 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/proximity/everlight,pm16d17.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Everlight PM-16D17 Ambient Light & Proximity Sensor
> +
> +maintainers:
> +  - Chao Zeng <chao.zeng@xxxxxxxxxxx>
> +
> +description: |
> +  This sensor uses standard I2C interface. Interrupt function is not covered.
> +  Datasheet: https://en.everlight.com/sensor/category-proximity_sensor/digital_proximity_sensor/
> +
> +properties:
> +  compatible:
> +    enum:
> +      - everlight,pm16d17
> +
> +  reg:
> +    maxItems: 1
> +
> +  ps-gain:
> +    description: Receiver gain of proximity sensor
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [1, 2, 4, 8]
> +    default: 1

This should I think be a userspace control.
Given it's not related to proximity as such, probably 
in_proximity0_hardwaregain

> +
> +  ps-itime:
> +    description: Conversion time for proximity sensor [ms]
> +    $ref: /schemas/types.yaml#/definitions/string
> +    enum:
> +      - "0.4"
> +      - "0.8"
> +      - "1.6"
> +      - "3.2"
> +      - "6.3"
> +      - "12.6"
> +      - "25.2"
> +    default: "0.4"
Definitely a userspace control.  Is this actually integration time
which we'd expect to affect the hardwaregain or is it just
1/ frequency of sampling (with fixed integration time).
Looking at datasheet it's coupled to resolution which may
make this oversampling related. Hard to tell.

> +
> +  ps-wtime:
> +    description: Waiting time for proximity sensor [ms]
I guess the above was the integration time and this sets
the sampling_frequency.  In that case definitely a userspace
thing, doesn't belong in DT.

> +    $ref: /schemas/types.yaml#/definitions/string
> +    enum:
> +      - "12.5"
> +      - "25"
> +      - "50"
> +      - "100"
> +      - "200"
> +      - "400"
> +      - "800"
> +      - "1600"
> +    default: "12.5"
> +
> +  ps-ir-led-pulse-count:
> +    description: IR LED drive pulse count

This needs more information.  Why would this be changed?
Seems from datasheet that this is effectively a different
form of gain. Why would we choose one rather than the other?
Or are they both ways of increasing the overall sensitivity?

> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    minimum: 1
> +    maximum: 256
> +    default: 1
> +
> +  ps-offset-cancel:
> +    description: |
> +      When PS offset cancel function is enabled, the result of subtracting any
> +      value specified by the PS offset cancel register from the internal PS
> +      output data is written to the PS output data register.
That sounds like a calibbias userspace control, but more info needed.

> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    default: 0
> +    maximum: 65535
> +
As Conor mentioned, need to describe the hardware as fully as possible so interrupts
and power supplies (even if they are always on for your particular board)

> +required:
> +  - compatible
> +  - reg
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        lightsensor: pm16d17@44 {
> +            compatible = "everlight,pm16d17";
> +            reg = <0x44>;
> +
> +            ps-gain = <1>;
> +            ps-itime = "0.4";
> +            ps-wtime = "12.5";
> +            ps-ir-led-pulse-count = <1>;
> +            ps-offset-cancel = <280>;
> +        };
> +    };