Reword a few descriptions, and normalize the text width to 80 characters.
Signed-off-by: Guillaume Stols <gstols@xxxxxxxxxxxx>
---
.../devicetree/bindings/iio/adc/adi,ad7606.yaml | 61 ++++++++++++----------
1 file changed, 34 insertions(+), 27 deletions(-)
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
index 00fdaed11cbd..80866940123c 100644
--- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
@@ -36,64 +36,71 @@ properties:
avcc-supply: true
interrupts:
+ description:
+ The BUSY pin falling edge indicates that the conversion is over, and thus
+ new data is available.
maxItems: 1
adi,conversion-start-gpios:
description:
- Must be the device tree identifier of the CONVST pin.
- This logic input is used to initiate conversions on the analog
- input channels. As the line is active high, it should be marked
- GPIO_ACTIVE_HIGH.
+ Must be the device tree identifier of the CONVST pin(s). This logic input
+ is used to initiate conversions on the analog input channels. As the line
+ is active high, it should be marked GPIO_ACTIVE_HIGH.
maxItems: 1
reset-gpios:
description:
- Must be the device tree identifier of the RESET pin. If specified,
- it will be asserted during driver probe. As the line is active high,
- it should be marked GPIO_ACTIVE_HIGH.
+ Must be the device tree identifier of the RESET pin. If specified, it will
+ be asserted during driver probe. On the AD7606x, as the line is active
+ high, it should be marked GPIO_ACTIVE_HIGH. On the AD7616, as the line is
+ active low, it should be marked GPIO_ACTIVE_LOW.
maxItems: 1
standby-gpios:
description:
- Must be the device tree identifier of the STBY pin. This pin is used
- to place the AD7606 into one of two power-down modes, Standby mode or
+ Must be the device tree identifier of the STBY pin. This pin is used to
+ place the AD7606 into one of two power-down modes, Standby mode or
Shutdown mode. As the line is active low, it should be marked
GPIO_ACTIVE_LOW.
maxItems: 1
adi,first-data-gpios:
description:
- Must be the device tree identifier of the FRSTDATA pin.
- The FRSTDATA output indicates when the first channel, V1, is
- being read back on either the parallel, byte or serial interface.
- As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
+ Must be the device tree identifier of the FRSTDATA pin. The FRSTDATA
+ output indicates when the first channel, V1, is being read back on either
+ the parallel, byte or serial interface. As the line is active
+ high, it should be marked GPIO_ACTIVE_HIGH.
maxItems: 1
adi,range-gpios:
description:
- Must be the device tree identifier of the RANGE pin. The polarity on
- this pin determines the input range of the analog input channels. If
- this pin is tied to a logic high, the analog input range is ±10V for
- all channels. If this pin is tied to a logic low, the analog input range
+ Must be the device tree identifier of the RANGE pin. The state on this
+ pin determines the input range of the analog input channels. If this pin
+ is tied to a logic high, the analog input range is ±10V for all channels.
+ On the AD760X, if this pin is tied to a logic low, the analog input range
is ±5V for all channels. As the line is active high, it should be marked
- GPIO_ACTIVE_HIGH.
+ GPIO_ACTIVE_HIGH. On the AD7616, there are 2 pins, and if the 2 pins are
+ tied to a logic high, software mode is enabled, otherwise one of the 3
+ possible range values is selected.
maxItems: 1
adi,oversampling-ratio-gpios:
description:
- Must be the device tree identifier of the over-sampling
- mode pins. As the line is active high, it should be marked
- GPIO_ACTIVE_HIGH.
+ Must be the device tree identifier of the over-sampling mode pins. As the
+ line is active high, it should be marked GPIO_ACTIVE_HIGH. On the AD7606X
+ parts that support it, if all 3 pins are tied to a logic high, software
+ mode is enabled.
maxItems: 3
adi,sw-mode:
description:
- Software mode of operation, so far available only for ad7616 and ad7606b.
- It is enabled when all three oversampling mode pins are connected to
- high level. The device is configured by the corresponding registers. If the
- adi,oversampling-ratio-gpios property is defined, then the driver will set the
- oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired
- to VDD.
+ Software mode of operation, so far available only for AD7616 and AD7606b.
+ It is enabled when all three oversampling mode pins are connected to high
+ level for the AD7606B, or all two range selection pins are connected to
+ high level for the AD7616. The device is configured by the corresponding
+ registers. If the adi,oversampling-ratio-gpios property is defined, then
+ the driver will set the oversampling gpios to high. Otherwise, it is
+ assumed that the pins are hardwired to VDD.
type: boolean
required:
--
2.34.1
