On Thu, 6 Jun 2024 23:23:09 +0200 Vasileios Amoiridis <vassilisamir@xxxxxxxxx> wrote: > Modify the startup procedure to reflect the procedure of > the Bosch BME68x Sensor API. The initial readings and > configuration of the sensor need to happen in the > following order: > > 1) Read calibration data [1,2] > 2) Chip general configuration [3] > 3) Gas configuration [4] > > After the chip configuration it is necessary to ensure that > the sensor is in sleeping mode, in order to apply the gas > configuration settings [5]. > Trivial but oddly short line wrapping. Target 75ish chars for commit messages > Also, after the soft reset, it is advised to wait for 5ms [6]. > > [1]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L162 > [2]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/examples/forced_mode/forced_mode.c#L44 > [3]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/examples/forced_mode/forced_mode.c#L53 > [4]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/examples/forced_mode/forced_mode.c#L60 > [5]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L640 > [6]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L294 Either make these Link tags or add a blank line here. I'd prefer link tags with # [1] etc after them for the cross references. > Signed-off-by: Vasileios Amoiridis <vassilisamir@xxxxxxxxx> > --- > drivers/iio/chemical/bme680.h | 2 ++ > drivers/iio/chemical/bme680_core.c | 21 ++++++++++++++------- > 2 files changed, 16 insertions(+), 7 deletions(-) > > diff --git a/drivers/iio/chemical/bme680.h b/drivers/iio/chemical/bme680.h > index 7d0ff294725a..b2c547ac8d34 100644 > --- a/drivers/iio/chemical/bme680.h > +++ b/drivers/iio/chemical/bme680.h > @@ -63,6 +63,8 @@ > > #define BME680_MEAS_TRIM_MASK GENMASK(24, 4) > > +#define BME680_STARTUP_TIME_US 5000 > + > /* Calibration Parameters */ > #define BME680_T2_LSB_REG 0x8A > #define BME680_H2_MSB_REG 0xE1 > diff --git a/drivers/iio/chemical/bme680_core.c b/drivers/iio/chemical/bme680_core.c > index 25d128e1ddcf..e354eaa34d59 100644 > --- a/drivers/iio/chemical/bme680_core.c > +++ b/drivers/iio/chemical/bme680_core.c > @@ -531,6 +531,11 @@ static int bme680_gas_config(struct bme680_data *data) > int ret; > u8 heatr_res, heatr_dur; > > + /* Go to sleep */ > + ret = bme680_set_mode(data, false); > + if (ret < 0) > + return ret; > + > heatr_res = bme680_calc_heater_res(data, data->heater_temp); > > /* set target heater temperature */ > @@ -866,6 +871,8 @@ int bme680_core_probe(struct device *dev, struct regmap *regmap, > return ret; > } > > + usleep_range(BME680_STARTUP_TIME_US, BME680_STARTUP_TIME_US + 1000); > + > ret = regmap_read(regmap, BME680_REG_CHIP_ID, &data->check); > if (ret < 0) { > dev_err(dev, "Error reading chip ID\n"); > @@ -878,22 +885,22 @@ int bme680_core_probe(struct device *dev, struct regmap *regmap, > return -ENODEV; > } > > - ret = bme680_chip_config(data); > + ret = bme680_read_calib(data, &data->bme680); > if (ret < 0) { > - dev_err(dev, "failed to set chip_config data\n"); > + dev_err(dev, > + "failed to read calibration coefficients at probe\n"); > return ret; > } > > - ret = bme680_gas_config(data); > + ret = bme680_chip_config(data); > if (ret < 0) { > - dev_err(dev, "failed to set gas config data\n"); > + dev_err(dev, "failed to set chip_config data\n"); > return ret; > } > > - ret = bme680_read_calib(data, &data->bme680); > + ret = bme680_gas_config(data); > if (ret < 0) { > - dev_err(dev, > - "failed to read calibration coefficients at probe\n"); > + dev_err(dev, "failed to set gas config data\n"); > return ret; > } >
