Calibration data are located in contiguous-ish registers inside the chip. For that reason we can use bulk reads as is done as well in the BME68x Sensor API [1]. The arrays that are used for reading the data out of the sensor are located inside DMA safe buffer. [1]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L1769 Signed-off-by: Vasileios Amoiridis <vassilisamir@xxxxxxxxx> --- drivers/iio/chemical/bme680.h | 28 +-- drivers/iio/chemical/bme680_core.c | 279 ++++++++++------------------- 2 files changed, 97 insertions(+), 210 deletions(-) diff --git a/drivers/iio/chemical/bme680.h b/drivers/iio/chemical/bme680.h index b5f16ca81e70..8d0f53c05d7d 100644 --- a/drivers/iio/chemical/bme680.h +++ b/drivers/iio/chemical/bme680.h @@ -39,10 +39,8 @@ #define BME680_HUM_REG_SHIFT_VAL 4 #define BME680_BIT_H1_DATA_MASK GENMASK(3, 0) -#define BME680_REG_RES_HEAT_RANGE 0x02 #define BME680_RHRANGE_MASK GENMASK(5, 4) #define BME680_REG_RES_HEAT_VAL 0x00 -#define BME680_REG_RANGE_SW_ERR 0x04 #define BME680_RSERROR_MASK GENMASK(7, 4) #define BME680_REG_RES_HEAT_0 0x5A #define BME680_REG_GAS_WAIT_0 0x64 @@ -60,31 +58,13 @@ /* Calibration Parameters */ #define BME680_T2_LSB_REG 0x8A -#define BME680_T3_REG 0x8C -#define BME680_P1_LSB_REG 0x8E -#define BME680_P2_LSB_REG 0x90 -#define BME680_P3_REG 0x92 -#define BME680_P4_LSB_REG 0x94 -#define BME680_P5_LSB_REG 0x96 -#define BME680_P7_REG 0x98 -#define BME680_P6_REG 0x99 -#define BME680_P8_LSB_REG 0x9C -#define BME680_P9_LSB_REG 0x9E -#define BME680_P10_REG 0xA0 -#define BME680_H2_LSB_REG 0xE2 #define BME680_H2_MSB_REG 0xE1 -#define BME680_H1_MSB_REG 0xE3 -#define BME680_H1_LSB_REG 0xE2 -#define BME680_H3_REG 0xE4 -#define BME680_H4_REG 0xE5 -#define BME680_H5_REG 0xE6 -#define BME680_H6_REG 0xE7 -#define BME680_H7_REG 0xE8 -#define BME680_T1_LSB_REG 0xE9 -#define BME680_GH2_LSB_REG 0xEB -#define BME680_GH1_REG 0xED #define BME680_GH3_REG 0xEE +#define BME680_CALIB_RANGE_1_LEN 23 +#define BME680_CALIB_RANGE_2_LEN 14 +#define BME680_CALIB_RANGE_3_LEN 5 + extern const struct regmap_config bme680_regmap_config; int bme680_core_probe(struct device *dev, struct regmap *regmap, diff --git a/drivers/iio/chemical/bme680_core.c b/drivers/iio/chemical/bme680_core.c index c1e191ed4955..f96cd4157c95 100644 --- a/drivers/iio/chemical/bme680_core.c +++ b/drivers/iio/chemical/bme680_core.c @@ -19,8 +19,53 @@ #include <linux/iio/iio.h> #include <linux/iio/sysfs.h> +#include <asm/unaligned.h> + #include "bme680.h" +/* 1st set of calibration data */ +enum { + /* Temperature calib indexes */ + T2_LSB = 0, + T3 = 2, + /* Pressure calib indexes */ + P1_LSB = 4, + P2_LSB = 6, + P3 = 8, + P4_LSB = 10, + P5_LSB = 12, + P7 = 14, + P6 = 15, + P8_LSB = 18, + P9_LSB = 20, + P10 = 22, +}; + +/* 2nd set of calibration data */ +enum { + /* Humidity calib indexes */ + H2_MSB = 0, + H1_LSB = 1, + H3 = 3, + H4 = 4, + H5 = 5, + H6 = 6, + H7 = 7, + /* Stray T1 calib index */ + T1_LSB = 8, + /* Gas heater calib indexes */ + GH2_LSB = 10, + GH1 = 12, + GH3 = 13, +}; + +/* 3rd set of calibration data */ +enum { + RES_HEAT_VAL = 0, + RES_HEAT_RANGE = 2, + RANGE_SW_ERR = 4, +}; + struct bme680_calib { u16 par_t1; s16 par_t2; @@ -64,6 +109,12 @@ struct bme680_data { * and humidity compensation calculations. */ s32 t_fine; + + union { + u8 bme680_cal_buf_1[BME680_CALIB_RANGE_1_LEN]; + u8 bme680_cal_buf_2[BME680_CALIB_RANGE_2_LEN]; + u8 bme680_cal_buf_3[BME680_CALIB_RANGE_3_LEN]; + }; }; static const struct regmap_range bme680_volatile_ranges[] = { @@ -112,217 +163,73 @@ static int bme680_read_calib(struct bme680_data *data, struct bme680_calib *calib) { struct device *dev = regmap_get_device(data->regmap); - unsigned int tmp, tmp_msb, tmp_lsb; + unsigned int tmp_msb, tmp_lsb; int ret; - __le16 buf; - - /* Temperature related coefficients */ - ret = regmap_bulk_read(data->regmap, BME680_T1_LSB_REG, - &buf, sizeof(buf)); - if (ret < 0) { - dev_err(dev, "failed to read BME680_T1_LSB_REG\n"); - return ret; - } - calib->par_t1 = le16_to_cpu(buf); ret = regmap_bulk_read(data->regmap, BME680_T2_LSB_REG, - &buf, sizeof(buf)); - if (ret < 0) { - dev_err(dev, "failed to read BME680_T2_LSB_REG\n"); - return ret; - } - calib->par_t2 = le16_to_cpu(buf); - - ret = regmap_read(data->regmap, BME680_T3_REG, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read BME680_T3_REG\n"); - return ret; - } - calib->par_t3 = tmp; - - /* Pressure related coefficients */ - ret = regmap_bulk_read(data->regmap, BME680_P1_LSB_REG, - &buf, sizeof(buf)); - if (ret < 0) { - dev_err(dev, "failed to read BME680_P1_LSB_REG\n"); - return ret; - } - calib->par_p1 = le16_to_cpu(buf); - - ret = regmap_bulk_read(data->regmap, BME680_P2_LSB_REG, - &buf, sizeof(buf)); - if (ret < 0) { - dev_err(dev, "failed to read BME680_P2_LSB_REG\n"); - return ret; - } - calib->par_p2 = le16_to_cpu(buf); - - ret = regmap_read(data->regmap, BME680_P3_REG, &tmp); + data->bme680_cal_buf_1, + sizeof(data->bme680_cal_buf_1)); if (ret < 0) { - dev_err(dev, "failed to read BME680_P3_REG\n"); + dev_err(dev, "failed to read 1st set of calib data;\n"); return ret; } - calib->par_p3 = tmp; - ret = regmap_bulk_read(data->regmap, BME680_P4_LSB_REG, - &buf, sizeof(buf)); - if (ret < 0) { - dev_err(dev, "failed to read BME680_P4_LSB_REG\n"); - return ret; - } - calib->par_p4 = le16_to_cpu(buf); + calib->par_t2 = get_unaligned_le16(&data->bme680_cal_buf_1[T2_LSB]); + calib->par_t3 = data->bme680_cal_buf_1[T3]; + calib->par_p1 = get_unaligned_le16(&data->bme680_cal_buf_1[P1_LSB]); + calib->par_p2 = get_unaligned_le16(&data->bme680_cal_buf_1[P2_LSB]); + calib->par_p3 = data->bme680_cal_buf_1[P3]; + calib->par_p4 = get_unaligned_le16(&data->bme680_cal_buf_1[P4_LSB]); + calib->par_p5 = get_unaligned_le16(&data->bme680_cal_buf_1[P5_LSB]); + calib->par_p7 = data->bme680_cal_buf_1[P7]; + calib->par_p6 = data->bme680_cal_buf_1[P6]; + calib->par_p8 = get_unaligned_le16(&data->bme680_cal_buf_1[P8_LSB]); + calib->par_p9 = get_unaligned_le16(&data->bme680_cal_buf_1[P9_LSB]); + calib->par_p10 = data->bme680_cal_buf_1[P10]; - ret = regmap_bulk_read(data->regmap, BME680_P5_LSB_REG, - &buf, sizeof(buf)); + ret = regmap_bulk_read(data->regmap, BME680_H2_MSB_REG, + data->bme680_cal_buf_2, + sizeof(data->bme680_cal_buf_2)); if (ret < 0) { - dev_err(dev, "failed to read BME680_P5_LSB_REG\n"); + dev_err(dev, "failed to read 2nd set of calib data;\n"); return ret; } - calib->par_p5 = le16_to_cpu(buf); - ret = regmap_read(data->regmap, BME680_P6_REG, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read BME680_P6_REG\n"); - return ret; - } - calib->par_p6 = tmp; - - ret = regmap_read(data->regmap, BME680_P7_REG, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read BME680_P7_REG\n"); - return ret; - } - calib->par_p7 = tmp; - - ret = regmap_bulk_read(data->regmap, BME680_P8_LSB_REG, - &buf, sizeof(buf)); - if (ret < 0) { - dev_err(dev, "failed to read BME680_P8_LSB_REG\n"); - return ret; - } - calib->par_p8 = le16_to_cpu(buf); - - ret = regmap_bulk_read(data->regmap, BME680_P9_LSB_REG, - &buf, sizeof(buf)); - if (ret < 0) { - dev_err(dev, "failed to read BME680_P9_LSB_REG\n"); - return ret; - } - calib->par_p9 = le16_to_cpu(buf); - - ret = regmap_read(data->regmap, BME680_P10_REG, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read BME680_P10_REG\n"); - return ret; - } - calib->par_p10 = tmp; - - /* Humidity related coefficients */ - ret = regmap_read(data->regmap, BME680_H1_MSB_REG, &tmp_msb); - if (ret < 0) { - dev_err(dev, "failed to read BME680_H1_MSB_REG\n"); - return ret; - } - ret = regmap_read(data->regmap, BME680_H1_LSB_REG, &tmp_lsb); - if (ret < 0) { - dev_err(dev, "failed to read BME680_H1_LSB_REG\n"); - return ret; - } + tmp_lsb = data->bme680_cal_buf_2[H1_LSB]; + tmp_msb = data->bme680_cal_buf_2[H1_LSB + 1]; calib->par_h1 = (tmp_msb << BME680_HUM_REG_SHIFT_VAL) | (tmp_lsb & BME680_BIT_H1_DATA_MASK); - ret = regmap_read(data->regmap, BME680_H2_MSB_REG, &tmp_msb); - if (ret < 0) { - dev_err(dev, "failed to read BME680_H2_MSB_REG\n"); - return ret; - } - ret = regmap_read(data->regmap, BME680_H2_LSB_REG, &tmp_lsb); - if (ret < 0) { - dev_err(dev, "failed to read BME680_H2_LSB_REG\n"); - return ret; - } + tmp_msb = data->bme680_cal_buf_2[H2_MSB]; + tmp_lsb = data->bme680_cal_buf_2[H2_MSB + 1]; calib->par_h2 = (tmp_msb << BME680_HUM_REG_SHIFT_VAL) | (tmp_lsb >> BME680_HUM_REG_SHIFT_VAL); - ret = regmap_read(data->regmap, BME680_H3_REG, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read BME680_H3_REG\n"); - return ret; - } - calib->par_h3 = tmp; + calib->par_h3 = data->bme680_cal_buf_2[H3]; + calib->par_h4 = data->bme680_cal_buf_2[H4]; + calib->par_h5 = data->bme680_cal_buf_2[H5]; + calib->par_h6 = data->bme680_cal_buf_2[H6]; + calib->par_h7 = data->bme680_cal_buf_2[H7]; + calib->par_t1 = get_unaligned_le16(&data->bme680_cal_buf_2[T1_LSB]); + calib->par_gh2 = get_unaligned_le16(&data->bme680_cal_buf_2[GH2_LSB]); + calib->par_gh1 = data->bme680_cal_buf_2[GH1]; + calib->par_gh3 = data->bme680_cal_buf_2[GH3]; - ret = regmap_read(data->regmap, BME680_H4_REG, &tmp); + ret = regmap_bulk_read(data->regmap, BME680_REG_RES_HEAT_VAL, + data->bme680_cal_buf_3, + sizeof(data->bme680_cal_buf_3)); if (ret < 0) { - dev_err(dev, "failed to read BME680_H4_REG\n"); + dev_err(dev, "failed to read 3rd set of calib data;\n"); return ret; } - calib->par_h4 = tmp; - ret = regmap_read(data->regmap, BME680_H5_REG, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read BME680_H5_REG\n"); - return ret; - } - calib->par_h5 = tmp; + calib->res_heat_val = data->bme680_cal_buf_3[RES_HEAT_VAL]; - ret = regmap_read(data->regmap, BME680_H6_REG, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read BME680_H6_REG\n"); - return ret; - } - calib->par_h6 = tmp; + calib->res_heat_range = FIELD_GET(BME680_RHRANGE_MASK, + data->bme680_cal_buf_3[RES_HEAT_RANGE]); - ret = regmap_read(data->regmap, BME680_H7_REG, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read BME680_H7_REG\n"); - return ret; - } - calib->par_h7 = tmp; - - /* Gas heater related coefficients */ - ret = regmap_read(data->regmap, BME680_GH1_REG, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read BME680_GH1_REG\n"); - return ret; - } - calib->par_gh1 = tmp; - - ret = regmap_bulk_read(data->regmap, BME680_GH2_LSB_REG, - &buf, sizeof(buf)); - if (ret < 0) { - dev_err(dev, "failed to read BME680_GH2_LSB_REG\n"); - return ret; - } - calib->par_gh2 = le16_to_cpu(buf); - - ret = regmap_read(data->regmap, BME680_GH3_REG, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read BME680_GH3_REG\n"); - return ret; - } - calib->par_gh3 = tmp; - - /* Other coefficients */ - ret = regmap_read(data->regmap, BME680_REG_RES_HEAT_RANGE, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read resistance heat range\n"); - return ret; - } - calib->res_heat_range = FIELD_GET(BME680_RHRANGE_MASK, tmp); - - ret = regmap_read(data->regmap, BME680_REG_RES_HEAT_VAL, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read resistance heat value\n"); - return ret; - } - calib->res_heat_val = tmp; - - ret = regmap_read(data->regmap, BME680_REG_RANGE_SW_ERR, &tmp); - if (ret < 0) { - dev_err(dev, "failed to read range software error\n"); - return ret; - } - calib->range_sw_err = FIELD_GET(BME680_RSERROR_MASK, tmp); + calib->range_sw_err = FIELD_GET(BME680_RSERROR_MASK, + data->bme680_cal_buf_3[RANGE_SW_ERR]); return 0; } -- 2.25.1
