[PATCH v4 6/6] iio: adc: ad7173: Add support for AD411x devices

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Dumitru Ceclan <dumitru.ceclan@xxxxxxxxxx>

Add support for AD4111/AD4112/AD4114/AD4115/AD4116.

The AD411X family encompasses a series of low power, low noise, 24-bit,
sigma-delta analog-to-digital converters that offer a versatile range of
specifications.

This family of ADCs integrates an analog front end suitable for processing
both fully differential and single-ended, bipolar voltage inputs
addressing a wide array of industrial and instrumentation requirements.

- All ADCs have inputs with a precision voltage divider with a division
  ratio of 10.
- AD4116 has 5 low level inputs without a voltage divider.
- AD4111 and AD4112 support current inputs (0 mA to 20 mA) using a 50ohm
  shunt resistor.

Signed-off-by: Dumitru Ceclan <dumitru.ceclan@xxxxxxxxxx>
---
 drivers/iio/adc/ad7173.c | 336 +++++++++++++++++++++++++++++++++++++++++++----
 1 file changed, 307 insertions(+), 29 deletions(-)

diff --git a/drivers/iio/adc/ad7173.c b/drivers/iio/adc/ad7173.c
index ed8ff8c5f343..91ff984eedf4 100644
--- a/drivers/iio/adc/ad7173.c
+++ b/drivers/iio/adc/ad7173.c
@@ -1,8 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * AD717x family SPI ADC driver
+ * AD717x and AD411x family SPI ADC driver
  *
  * Supported devices:
+ *  AD4111/AD4112/AD4114/AD4115/AD4116
  *  AD7172-2/AD7172-4/AD7173-8/AD7175-2
  *  AD7175-8/AD7176-2/AD7177-2
  *
@@ -77,6 +78,11 @@
 #define AD7175_2_ID			0x0cd0
 #define AD7172_4_ID			0x2050
 #define AD7173_ID			0x30d0
+#define AD4111_ID			AD7173_ID
+#define AD4112_ID			AD7173_ID
+#define AD4114_ID			AD7173_ID
+#define AD4116_ID			0x34d0
+#define AD4115_ID			0x38d0
 #define AD7175_8_ID			0x3cd0
 #define AD7177_ID			0x4fd0
 #define AD7173_ID_MASK			GENMASK(15, 4)
@@ -107,6 +113,7 @@
 
 #define AD7173_GPO12_DATA(x)	BIT((x) + 0)
 #define AD7173_GPO23_DATA(x)	BIT((x) + 4)
+#define AD4111_GPO01_DATA(x)	BIT((x) + 6)
 #define AD7173_GPO_DATA(x)	((x) < 2 ? AD7173_GPO12_DATA(x) : AD7173_GPO23_DATA(x))
 
 #define AD7173_INTERFACE_DATA_STAT	BIT(6)
@@ -125,26 +132,46 @@
 #define AD7173_VOLTAGE_INT_REF_uV	2500000
 #define AD7173_TEMP_SENSIIVITY_uV_per_C	477
 #define AD7177_ODR_START_VALUE		0x07
+#define AD4111_SHUNT_RESISTOR_OHM	50
+#define AD4111_DIVIDER_RATIO		10
+#define AD411X_VCOM_INPUT		0X10
+#define AD4111_CURRENT_CHAN_CUTOFF	16
 
 #define AD7173_FILTER_ODR0_MASK		GENMASK(5, 0)
 #define AD7173_MAX_CONFIGS		8
 
+enum ad4111_current_channels {
+	AD4111_CURRENT_IN0P_IN0N,
+	AD4111_CURRENT_IN1P_IN1N,
+	AD4111_CURRENT_IN2P_IN2N,
+	AD4111_CURRENT_IN3P_IN3N,
+};
+
 struct ad7173_device_info {
 	const unsigned int *sinc5_data_rates;
 	unsigned int num_sinc5_data_rates;
 	unsigned int odr_start_value;
+	/*
+	 * AD4116 has both inputs with a voltage divider and without.
+	 * These inputs cannot be mixed in the channel configuration.
+	 * Does not include the VINCOM input.
+	 */
+	unsigned int num_voltage_in_div;
 	unsigned int num_channels;
 	unsigned int num_configs;
-	unsigned int num_inputs;
+	unsigned int num_voltage_in;
 	unsigned int clock;
 	unsigned int id;
 	char *name;
+	bool has_current_inputs;
+	bool has_vcom_input;
 	bool has_temp;
 	/* ((AVDD1 − AVSS)/5) */
 	bool has_common_input;
 	bool has_input_buf;
 	bool has_int_ref;
 	bool has_ref2;
+	bool higher_gpio_bits;
 	u8 num_gpios;
 };
 
@@ -186,6 +213,24 @@ struct ad7173_state {
 #endif
 };
 
+static unsigned int ad4115_sinc5_data_rates[] = {
+	24845000, 24845000, 20725000, 20725000,	/*  0-3  */
+	15564000, 13841000, 10390000, 10390000,	/*  4-7  */
+	4994000,  2499000,  1000000,  500000,	/*  8-11 */
+	395500,   200000,   100000,   59890,	/* 12-15 */
+	49920,    20000,    16660,    10000,	/* 16-19 */
+	5000,	  2500,     2500,		/* 20-22 */
+};
+
+static unsigned int ad4116_sinc5_data_rates[] = {
+	12422360, 12422360, 12422360, 12422360,	/*  0-3  */
+	10362690, 10362690, 7782100,  6290530,	/*  4-7  */
+	5194800,  2496900,  1007600,  499900,	/*  8-11 */
+	390600,	  200300,   100000,   59750,	/* 12-15 */
+	49840,	  20000,    16650,    10000,	/* 16-19 */
+	5000,	  2500,	    1250,		/* 20-22 */
+};
+
 static const unsigned int ad7173_sinc5_data_rates[] = {
 	6211000, 6211000, 6211000, 6211000, 6211000, 6211000, 5181000, 4444000,	/*  0-7  */
 	3115000, 2597000, 1007000, 503800,  381000,  200300,  100500,  59520,	/*  8-15 */
@@ -201,13 +246,113 @@ static const unsigned int ad7175_sinc5_data_rates[] = {
 	5000,					/* 20    */
 };
 
+static unsigned int ad4111_current_channel_config[] = {
+	[AD4111_CURRENT_IN0P_IN0N] = 0x1E8,
+	[AD4111_CURRENT_IN1P_IN1N] = 0x1C9,
+	[AD4111_CURRENT_IN2P_IN2N] = 0x1AA,
+	[AD4111_CURRENT_IN3P_IN3N] = 0x18B,
+};
+
+static const struct ad7173_device_info ad4111_device_info = {
+	.name = "ad4111",
+	.id = AD4111_ID,
+	.num_voltage_in_div = 8,
+	.num_channels = 16,
+	.num_configs = 8,
+	.num_voltage_in = 8,
+	.num_gpios = 2,
+	.higher_gpio_bits = true,
+	.has_temp = true,
+	.has_vcom_input = true,
+	.has_input_buf = true,
+	.has_current_inputs = true,
+	.has_int_ref = true,
+	.clock = 2 * HZ_PER_MHZ,
+	.sinc5_data_rates = ad7173_sinc5_data_rates,
+	.num_sinc5_data_rates = ARRAY_SIZE(ad7173_sinc5_data_rates),
+};
+
+static const struct ad7173_device_info ad4112_device_info = {
+	.name = "ad4112",
+	.id = AD4112_ID,
+	.num_voltage_in_div = 8,
+	.num_channels = 16,
+	.num_configs = 8,
+	.num_voltage_in = 8,
+	.num_gpios = 2,
+	.higher_gpio_bits = true,
+	.has_vcom_input = true,
+	.has_temp = true,
+	.has_input_buf = true,
+	.has_current_inputs = true,
+	.has_int_ref = true,
+	.clock = 2 * HZ_PER_MHZ,
+	.sinc5_data_rates = ad7173_sinc5_data_rates,
+	.num_sinc5_data_rates = ARRAY_SIZE(ad7173_sinc5_data_rates),
+};
+
+static const struct ad7173_device_info ad4114_device_info = {
+	.name = "ad4114",
+	.id = AD4114_ID,
+	.num_voltage_in_div = 16,
+	.num_channels = 16,
+	.num_configs = 8,
+	.num_voltage_in = 16,
+	.num_gpios = 4,
+	.higher_gpio_bits = true,
+	.has_vcom_input = true,
+	.has_temp = true,
+	.has_input_buf = true,
+	.has_int_ref = true,
+	.clock = 2 * HZ_PER_MHZ,
+	.sinc5_data_rates = ad7173_sinc5_data_rates,
+	.num_sinc5_data_rates = ARRAY_SIZE(ad7173_sinc5_data_rates),
+};
+
+static const struct ad7173_device_info ad4115_device_info = {
+	.name = "ad4115",
+	.id = AD4115_ID,
+	.num_voltage_in_div = 16,
+	.num_channels = 16,
+	.num_configs = 8,
+	.num_voltage_in = 16,
+	.num_gpios = 4,
+	.higher_gpio_bits = true,
+	.has_vcom_input = true,
+	.has_temp = true,
+	.has_input_buf = true,
+	.has_int_ref = true,
+	.clock = 8 * HZ_PER_MHZ,
+	.sinc5_data_rates = ad4115_sinc5_data_rates,
+	.num_sinc5_data_rates = ARRAY_SIZE(ad4115_sinc5_data_rates),
+};
+
+static const struct ad7173_device_info ad4116_device_info = {
+	.name = "ad4116",
+	.id = AD4116_ID,
+	.num_voltage_in_div = 11,
+	.num_channels = 16,
+	.num_configs = 8,
+	.num_voltage_in = 16,
+	.num_gpios = 4,
+	.higher_gpio_bits = true,
+	.has_vcom_input = true,
+	.has_temp = true,
+	.has_input_buf = true,
+	.has_int_ref = true,
+	.clock = 4 * HZ_PER_MHZ,
+	.sinc5_data_rates = ad4116_sinc5_data_rates,
+	.num_sinc5_data_rates = ARRAY_SIZE(ad4116_sinc5_data_rates),
+};
+
 static const struct ad7173_device_info ad7172_2_device_info = {
 	.name = "ad7172-2",
 	.id = AD7172_2_ID,
-	.num_inputs = 5,
+	.num_voltage_in = 5,
 	.num_channels = 4,
 	.num_configs = 4,
 	.num_gpios = 2,
+	.higher_gpio_bits = false,
 	.has_temp = true,
 	.has_input_buf = true,
 	.has_int_ref = true,
@@ -220,10 +365,11 @@ static const struct ad7173_device_info ad7172_2_device_info = {
 static const struct ad7173_device_info ad7172_4_device_info = {
 	.name = "ad7172-4",
 	.id = AD7172_4_ID,
-	.num_inputs = 9,
+	.num_voltage_in = 9,
 	.num_channels = 8,
 	.num_configs = 8,
 	.num_gpios = 4,
+	.higher_gpio_bits = false,
 	.has_temp = false,
 	.has_input_buf = true,
 	.has_ref2 = true,
@@ -236,10 +382,11 @@ static const struct ad7173_device_info ad7172_4_device_info = {
 static const struct ad7173_device_info ad7173_8_device_info = {
 	.name = "ad7173-8",
 	.id = AD7173_ID,
-	.num_inputs = 17,
+	.num_voltage_in = 17,
 	.num_channels = 16,
 	.num_configs = 8,
 	.num_gpios = 4,
+	.higher_gpio_bits = false,
 	.has_temp = true,
 	.has_input_buf = true,
 	.has_int_ref = true,
@@ -253,10 +400,11 @@ static const struct ad7173_device_info ad7173_8_device_info = {
 static const struct ad7173_device_info ad7175_2_device_info = {
 	.name = "ad7175-2",
 	.id = AD7175_2_ID,
-	.num_inputs = 5,
+	.num_voltage_in = 5,
 	.num_channels = 4,
 	.num_configs = 4,
 	.num_gpios = 2,
+	.higher_gpio_bits = false,
 	.has_temp = true,
 	.has_input_buf = true,
 	.has_int_ref = true,
@@ -269,10 +417,11 @@ static const struct ad7173_device_info ad7175_2_device_info = {
 static const struct ad7173_device_info ad7175_8_device_info = {
 	.name = "ad7175-8",
 	.id = AD7175_8_ID,
-	.num_inputs = 17,
+	.num_voltage_in = 17,
 	.num_channels = 16,
 	.num_configs = 8,
 	.num_gpios = 4,
+	.higher_gpio_bits = false,
 	.has_temp = true,
 	.has_input_buf = true,
 	.has_int_ref = true,
@@ -286,10 +435,11 @@ static const struct ad7173_device_info ad7175_8_device_info = {
 static const struct ad7173_device_info ad7176_2_device_info = {
 	.name = "ad7176-2",
 	.id = AD7176_ID,
-	.num_inputs = 5,
+	.num_voltage_in = 5,
 	.num_channels = 4,
 	.num_configs = 4,
 	.num_gpios = 2,
+	.higher_gpio_bits = false,
 	.has_temp = false,
 	.has_input_buf = false,
 	.has_int_ref = true,
@@ -302,10 +452,11 @@ static const struct ad7173_device_info ad7176_2_device_info = {
 static const struct ad7173_device_info ad7177_2_device_info = {
 	.name = "ad7177-2",
 	.id = AD7177_ID,
-	.num_inputs = 5,
+	.num_voltage_in = 5,
 	.num_channels = 4,
 	.num_configs = 4,
 	.num_gpios = 2,
+	.higher_gpio_bits = false,
 	.has_temp = true,
 	.has_input_buf = true,
 	.has_int_ref = true,
@@ -355,6 +506,15 @@ static int ad7173_mask_xlate(struct gpio_regmap *gpio, unsigned int base,
 	return 0;
 }
 
+static int ad4111_mask_xlate(struct gpio_regmap *gpio, unsigned int base,
+			     unsigned int offset, unsigned int *reg,
+			     unsigned int *mask)
+{
+	*mask = AD4111_GPO01_DATA(offset);
+	*reg = base;
+	return 0;
+}
+
 static void ad7173_gpio_disable(void *data)
 {
 	struct ad7173_state *st = data;
@@ -387,7 +547,10 @@ static int ad7173_gpio_init(struct ad7173_state *st)
 	gpio_regmap.regmap = st->reg_gpiocon_regmap;
 	gpio_regmap.ngpio = st->info->num_gpios;
 	gpio_regmap.reg_set_base = AD7173_REG_GPIO;
-	gpio_regmap.reg_mask_xlate = ad7173_mask_xlate;
+	if (st->info->higher_gpio_bits)
+		gpio_regmap.reg_mask_xlate = ad4111_mask_xlate;
+	else
+		gpio_regmap.reg_mask_xlate = ad7173_mask_xlate;
 
 	st->gpio_regmap = devm_gpio_regmap_register(dev, &gpio_regmap);
 	ret = PTR_ERR_OR_ZERO(st->gpio_regmap);
@@ -686,18 +849,33 @@ static int ad7173_read_raw(struct iio_dev *indio_dev,
 
 		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_SCALE:
-		if (chan->type == IIO_TEMP) {
+
+		switch (chan->type) {
+		case IIO_TEMP:
 			temp = AD7173_VOLTAGE_INT_REF_uV * MILLI;
 			temp /= AD7173_TEMP_SENSIIVITY_uV_per_C;
 			*val = temp;
 			*val2 = chan->scan_type.realbits;
-		} else {
+			return IIO_VAL_FRACTIONAL_LOG2;
+		case IIO_VOLTAGE:
 			*val = ad7173_get_ref_voltage_milli(st, ch->cfg.ref_sel);
 			*val2 = chan->scan_type.realbits - !!(ch->cfg.bipolar);
+
+			if (chan->channel < st->info->num_voltage_in_div)
+				*val *= AD4111_DIVIDER_RATIO;
+			return IIO_VAL_FRACTIONAL_LOG2;
+		case IIO_CURRENT:
+			*val = ad7173_get_ref_voltage_milli(st, ch->cfg.ref_sel);
+			*val /= AD4111_SHUNT_RESISTOR_OHM;
+			*val2 = chan->scan_type.realbits - ch->cfg.bipolar;
+			return IIO_VAL_FRACTIONAL_LOG2;
+		default:
+			return -EINVAL;
 		}
-		return IIO_VAL_FRACTIONAL_LOG2;
 	case IIO_CHAN_INFO_OFFSET:
-		if (chan->type == IIO_TEMP) {
+
+		switch (chan->type) {
+		case IIO_TEMP:
 			/* 0 Kelvin -> raw sample */
 			temp   = -ABSOLUTE_ZERO_MILLICELSIUS;
 			temp  *= AD7173_TEMP_SENSIIVITY_uV_per_C;
@@ -706,10 +884,14 @@ static int ad7173_read_raw(struct iio_dev *indio_dev,
 						       AD7173_VOLTAGE_INT_REF_uV *
 						       MILLI);
 			*val   = -temp;
-		} else {
+			return IIO_VAL_INT;
+		case IIO_VOLTAGE:
+		case IIO_CURRENT:
 			*val = -BIT(chan->scan_type.realbits - 1);
+			return IIO_VAL_INT;
+		default:
+			return -EINVAL;
 		}
-		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_SAMP_FREQ:
 		reg = st->channels[chan->address].cfg.odr;
 
@@ -736,6 +918,21 @@ static int ad7173_write_raw(struct iio_dev *indio_dev,
 		return ret;
 
 	switch (info) {
+	/*
+	 * This attribute sets the sampling frequency to each channel individually.
+	 * There are no issues for raw or buffered reads of an individual channel.
+	 *
+	 * When multiple channels are enabled in buffered mode, the effective
+	 * sampling rate of a channel is lowered in correlation to the number
+	 * of channels enabled and the sampling rate of the other channels.
+	 *
+	 * Example: 3 channels enabled with rates CH1:6211sps CH2,CH3:10sps
+	 * While the reading of CH1 takes only 0.16ms, the reading of CH2 and CH3
+	 * will take 100ms each.
+	 *
+	 * This will cause the reading of CH1 to be actually done once every
+	 * 200.16ms, an effective rate of 4.99sps.
+	 */
 	case IIO_CHAN_INFO_SAMP_FREQ:
 		freq = val * MILLI + val2 / MILLI;
 		for (i = st->info->odr_start_value; i < st->info->num_sinc5_data_rates - 1; i++)
@@ -916,13 +1113,34 @@ static int ad7173_register_clk_provider(struct iio_dev *indio_dev)
 					   &st->int_clk_hw);
 }
 
+static int ad4111_validate_current_ain(struct ad7173_state *st,
+				       const unsigned int ain[AD7173_NO_AINS_PER_CHANNEL])
+{
+	struct device *dev = &st->sd.spi->dev;
+
+	if (!st->info->has_current_inputs)
+		return dev_err_probe(dev, -EINVAL,
+			"Model %s does not support current channels\n",
+			st->info->name);
+
+	if (ain[0] >= ARRAY_SIZE(ad4111_current_channel_config))
+		return dev_err_probe(dev, -EINVAL,
+			"For current channels single-channel must be <[0-3]>\n");
+
+	return 0;
+}
+
 static int ad7173_validate_voltage_ain_inputs(struct ad7173_state *st,
 					      const unsigned int ain[AD7173_NO_AINS_PER_CHANNEL])
 {
 	struct device *dev = &st->sd.spi->dev;
+	bool ain_selects_normal_input[] = {
+		ain[0] < st->info->num_voltage_in,
+		ain[1] < st->info->num_voltage_in
+	};
 
 	for (int i = 0; i < AD7173_NO_AINS_PER_CHANNEL; i++) {
-		if (ain[i] < st->info->num_inputs)
+		if (ain_selects_normal_input[i])
 			continue;
 
 		if (ain[i] == AD7173_AIN_REF_POS || ain[i] == AD7173_AIN_REF_NEG)
@@ -933,11 +1151,27 @@ static int ad7173_validate_voltage_ain_inputs(struct ad7173_state *st,
 		    st->info->has_common_input)
 			continue;
 
+		if (st->info->has_vcom_input && ain[i] == AD411X_VCOM_INPUT) {
+			if (ain_selects_normal_input[(i + 1) % 2] &&
+			    ain[(i + 1) % 2] >= st->info->num_voltage_in_div)
+				return dev_err_probe(dev, -EINVAL,
+					"VCOM must be paired with inputs having divider.\n");
+
+			continue;
+		}
+
 		return dev_err_probe(dev, -EINVAL,
 			"Input pin number out of range for pair (%d %d).\n",
 			ain[0], ain[1]);
 	}
 
+	if ((ain_selects_normal_input[0] && ain_selects_normal_input[1]) &&
+	    ((ain[0] >= st->info->num_voltage_in_div) !=
+	     (ain[1] >= st->info->num_voltage_in_div)))
+		return dev_err_probe(dev, -EINVAL,
+			"Both inputs must either have a voltage divider or not have: (%d %d).\n",
+			ain[0], ain[1]);
+
 	return 0;
 }
 
@@ -968,7 +1202,7 @@ static int ad7173_fw_parse_channel_config(struct iio_dev *indio_dev)
 	struct device *dev = indio_dev->dev.parent;
 	struct iio_chan_spec *chan_arr, *chan;
 	unsigned int ain[AD7173_NO_AINS_PER_CHANNEL], chan_index = 0;
-	int ref_sel, ret, num_channels;
+	int ref_sel, ret, is_current_chan, num_channels;
 
 	num_channels = device_get_child_node_count(dev);
 
@@ -1015,15 +1249,41 @@ static int ad7173_fw_parse_channel_config(struct iio_dev *indio_dev)
 
 	device_for_each_child_node_scoped(dev, child) {
 		chan = &chan_arr[chan_index];
+		*chan = ad7173_channel_template;
 		chan_st_priv = &chans_st_arr[chan_index];
 		ret = fwnode_property_read_u32_array(child, "diff-channels",
 						     ain, ARRAY_SIZE(ain));
-		if (ret)
-			return ret;
+		if (ret) {
+			ret = fwnode_property_read_u32_array(child, "single-channel",
+							     ain, 1);
+			if (ret)
+				return dev_err_probe(dev, ret,
+					"Channel must define one of diff-channels or single-channel.\n");
 
-		ret = ad7173_validate_voltage_ain_inputs(st, ain);
-		if (ret)
-			return ret;
+			is_current_chan = fwnode_property_read_bool(child, "adi,current-channel");
+		} else {
+			chan->differential = true;
+		}
+
+		if (is_current_chan) {
+			ret = ad4111_validate_current_ain(st, ain);
+			if (ret)
+				return ret;
+			is_current_chan = true;
+			ain[1] = 0;
+		} else {
+			if (!chan->differential) {
+				ret = fwnode_property_read_u32_array(child,
+					"adi,common-mode-channel", ain + 1, 1);
+				if (ret)
+					return dev_err_probe(dev, ret,
+						"adi,common-mode-channel must be defined for single-ended channels.\n");
+			}
+			ret = ad7173_validate_voltage_ain_inputs(st, ain);
+			if (ret)
+				return ret;
+			is_current_chan = false;
+		}
 
 		ret = fwnode_property_match_property_string(child,
 							    "adi,reference-select",
@@ -1042,22 +1302,30 @@ static int ad7173_fw_parse_channel_config(struct iio_dev *indio_dev)
 			st->adc_mode |= AD7173_ADC_MODE_REF_EN;
 		chan_st_priv->cfg.ref_sel = ref_sel;
 
-		*chan = ad7173_channel_template;
 		chan->address = chan_index;
 		chan->scan_index = chan_index;
 		chan->channel = ain[0];
 		chan->channel2 = ain[1];
-		chan->differential = true;
-
-		chan_st_priv->ain = AD7173_CH_ADDRESS(ain[0], ain[1]);
 		chan_st_priv->chan_reg = chan_index;
 		chan_st_priv->cfg.input_buf = st->info->has_input_buf;
 		chan_st_priv->cfg.odr = 0;
-
 		chan_st_priv->cfg.bipolar = fwnode_property_read_bool(child, "bipolar");
+
 		if (chan_st_priv->cfg.bipolar)
 			chan->info_mask_separate |= BIT(IIO_CHAN_INFO_OFFSET);
 
+		if (is_current_chan) {
+			chan->type = IIO_CURRENT;
+			chan->differential = false;
+			ain[1] = FIELD_GET(AD7173_CH_SETUP_AINNEG_MASK,
+					   ad4111_current_channel_config[ain[0]]);
+			ain[0] = FIELD_GET(AD7173_CH_SETUP_AINPOS_MASK,
+					   ad4111_current_channel_config[ain[0]]);
+		} else {
+			chan_st_priv->cfg.input_buf = st->info->has_input_buf;
+		}
+		chan_st_priv->ain = AD7173_CH_ADDRESS(ain[0], ain[1]);
+
 		chan_index++;
 	}
 	return 0;
@@ -1184,6 +1452,11 @@ static int ad7173_probe(struct spi_device *spi)
 }
 
 static const struct of_device_id ad7173_of_match[] = {
+	{ .compatible = "ad4111",	.data = &ad4111_device_info},
+	{ .compatible = "ad4112",	.data = &ad4112_device_info},
+	{ .compatible = "ad4114",	.data = &ad4114_device_info},
+	{ .compatible = "ad4115",	.data = &ad4115_device_info},
+	{ .compatible = "ad4116",	.data = &ad4116_device_info},
 	{ .compatible = "adi,ad7172-2", .data = &ad7172_2_device_info},
 	{ .compatible = "adi,ad7172-4", .data = &ad7172_4_device_info},
 	{ .compatible = "adi,ad7173-8", .data = &ad7173_8_device_info},
@@ -1196,6 +1469,11 @@ static const struct of_device_id ad7173_of_match[] = {
 MODULE_DEVICE_TABLE(of, ad7173_of_match);
 
 static const struct spi_device_id ad7173_id_table[] = {
+	{ "ad4111",   (kernel_ulong_t)&ad4111_device_info},
+	{ "ad4112",   (kernel_ulong_t)&ad4112_device_info},
+	{ "ad4114",   (kernel_ulong_t)&ad4114_device_info},
+	{ "ad4115",   (kernel_ulong_t)&ad4115_device_info},
+	{ "ad4116",   (kernel_ulong_t)&ad4116_device_info},
 	{ "ad7172-2", (kernel_ulong_t)&ad7172_2_device_info},
 	{ "ad7172-4", (kernel_ulong_t)&ad7172_4_device_info},
 	{ "ad7173-8", (kernel_ulong_t)&ad7173_8_device_info},
@@ -1220,5 +1498,5 @@ module_spi_driver(ad7173_driver);
 MODULE_IMPORT_NS(IIO_AD_SIGMA_DELTA);
 MODULE_AUTHOR("Lars-Peter Clausen <lars@xxxxxxxxx>");
 MODULE_AUTHOR("Dumitru Ceclan <dumitru.ceclan@xxxxxxxxxx>");
-MODULE_DESCRIPTION("Analog Devices AD7172/AD7173/AD7175/AD7176 ADC driver");
+MODULE_DESCRIPTION("Analog Devices AD7173 and similar ADC driver");
 MODULE_LICENSE("GPL");

-- 
2.43.0






[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux