Re: [PATCH 01/13] spi: add core support for controllers with offload capabilities

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jan 10, 2024 at 3:36 PM Mark Brown <broonie@xxxxxxxxxx> wrote:
>
> On Wed, Jan 10, 2024 at 01:49:42PM -0600, David Lechner wrote:
> > This adds a feature for specialized SPI controllers that can record
> > a series of SPI transfers, including tx data, cs assertions, delays,
> > etc. and then play them back using a hardware trigger without CPU
> > intervention.
>
> > The intended use case for this is with the AXI SPI Engine to capture
> > data from ADCs at high rates (MSPS) with a stable sample period.
>
> > Most of the implementation is controller-specific and will be handled by
> > drivers that implement the offload_ops callbacks. The API follows a
> > prepare/enable pattern that should be familiar to users of the clk
> > subsystem.
>
> This is a lot to do in one go, and I think it's a bit too off on the
> side and unintegrated with the core.  There's two very high level bits
> here, there's the pre-cooking a message for offloading to be executed by
> a hardware engine and there's the bit where that's triggered by some
> hardwar event rather than by software.
>

...

>
> The bit where messages are initiated by hardware is a step beyond that,
> I think we need a bit more API for connecting up the triggers and we
> also need to have something handling what happens with normal operation
> of the device while these triggers are enabled.  I think it could be
> useful to split this bit out since there's a lot more to work out there
> in terms of interfaces.

Now that we have addressed the pre-cooking messages bit [1] I'm coming
back to the hardware trigger bit. Since the hardware trigger part
hasn't been discussed in the past, it's not so clear to me what is
being requested here (also see specific questions below).

[1]: https://lore.kernel.org/linux-spi/20240219-mainline-spi-precook-message-v2-0-4a762c6701b9@xxxxxxxxxxxx/T/#t

>
> > +/**
> > + * SPI_OFFLOAD_RX - placeholder for indicating read transfers for offloads
> > + *
> > + * Assign xfer->rx_buf to this value for any read transfer passed to
> > + * spi_offload_prepare(). This will act as a flag to indicate to the offload
> > + * that it should do something with the data read during this transfer. What
> > + * that something can be is determined by the specific hardware, e.g. it could
> > + * be piped to DMA or a DSP, etc.
> > + */
> > +#define SPI_OFFLOAD_RX_SENTINEL ((void *)1)
>
> This feels like something where there are likely to be multiple options
> and we need configurability.  I'd also expect to see a similar transmit
> option.

Having something similar for TX makes sense. What other sorts of
options are you envisioning here?

>
> > +int spi_offload_prepare(struct spi_offload *offload, struct spi_device *spi,
> > +                       struct spi_transfer *xfers, unsigned int num_xfers)
>
> I would expect us to just generically prepare a message, then pass a
> prepared message into the API that enables a trigger.  We would need
> something that handles the difference between potentially offloading for
> better performance and having a hardware trigger, I think that might be
> a case of just not exposing the engine's prepare to client drivers and
> then having the core track if it needs to do that when enabling a
> hardware trigger.

Not exposing the offload prepare to client drivers sounds reasonable.
I'm not sure I understand the potential need for an offload without a
hardware trigger though.

>
> > +     /**
> > +      * @enable: Callback to enable the offload.
> > +      */
> > +     int (*enable)(struct spi_offload *offload);
> > +     /**
> > +      * @disable: Callback to disable the offload.
> > +      */
> > +     void (*disable)(struct spi_offload *offload);
>
> I'm not seeing anything in this API that provides a mechanism for
> configuring what triggers things to start, even in the case where things
> are triggered by hardware rather than initiated by software I'd expect
> to see hardware with runtime configurability.  The binding is a bit
> unclear but it seems to be expecting this to be statically configured in
> hardware and that there will be a 1:1 mapping between triggers and
> scripts that can be configured, if nothing else I would expect that
> there will be hardware with more possible triggers than scripts.

For the use case of ADCs/DACs we would want a periodic trigger where
the period of the trigger is runtime configurable (via sysfs). Is this
the sort of thing you had in mind here? What other sorts of triggers
do you have in mind?

>
> I'd also expect some treatement of what happens with the standard SPI
> API while something is enabled.

I suppose it makes sense to return -EBUSY from
spi_sync()/spi_async()/spi_bus_lock() when a hardware trigger is
enabled.





[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux