Re: [PATCH v12 2/2] iio: adc: ad7173: add AD7173 driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, 18 Jan 2024 14:49:23 +0200
Dumitru Ceclan <mitrutzceclan@xxxxxxxxx> wrote:

> The AD7173 family offer a complete integrated Sigma-Delta ADC solution
> which can be used in high precision, low noise single channel
> applications or higher speed multiplexed applications. The Sigma-Delta
> ADC is intended primarily for measurement of signals close to DC but also
> delivers outstanding performance with input bandwidths out to ~10kHz.
> 
> Reviewed-by: Andy Shevchenko <andy@xxxxxxxxxx>
> Reviewed-by: Michael Walle <michael@xxxxxxxx> # for gpio-regmap
> Signed-off-by: Dumitru Ceclan <mitrutzceclan@xxxxxxxxx>

One comment following through from adding the named irq support to the
binding.  The driver needs to check that it has the right one
as perhaps only the error one is wired, or it is the first one specified
in the binding.


> +static int ad7173_probe(struct spi_device *spi)
> +{
> +	struct device *dev = &spi->dev;
> +	struct ad7173_state *st;
> +	struct iio_dev *indio_dev;
> +	int ret;
> +
> +	indio_dev = devm_iio_device_alloc(dev, sizeof(*st));
> +	if (!indio_dev)
> +		return -ENOMEM;
> +
> +	st = iio_priv(indio_dev);
> +	st->info = spi_get_device_match_data(spi);
> +	if (!st->info)
> +		return -ENODEV;
> +
> +	ida_init(&st->cfg_slots_status);
> +	ret = devm_add_action_or_reset(dev, ad7173_ida_destroy, st);
> +	if (ret)
> +		return ret;
> +
> +	indio_dev->name = st->info->name;
> +	indio_dev->modes = INDIO_DIRECT_MODE;
> +	indio_dev->info = &ad7173_info;
> +
> +	spi->mode = SPI_MODE_3;
> +
> +	ad7173_sigma_delta_info.num_slots = st->info->num_configs;
> +	ret = ad_sd_init(&st->sd, indio_dev, spi, &ad7173_sigma_delta_info);
> +	if (ret)
> +		return ret;
> +
> +	ret = ad7173_fw_parse_channel_config(indio_dev);
> +	if (ret)
> +		return ret;
> +
> +	ret = devm_ad_sd_setup_buffer_and_trigger(dev, indio_dev);

If the error interrupt is provided either first, or as the only interrupt
this is going to use the wrong one.

Probably need to have a variant of that which takes an explicit irq so that
figuring out which irq is relevant becomes a driver problem rather than the
library having a go based on spi->irq.


> +	if (ret)
> +		return ret;
> +
> +	ret = ad7173_setup(indio_dev);
> +	if (ret)
> +		return ret;
> +
> +	ret = devm_iio_device_register(dev, indio_dev);
> +	if (ret)
> +		return ret;
> +
> +	if (IS_ENABLED(CONFIG_GPIOLIB))
> +		return ad7173_gpio_init(st);
> +
> +	return 0;
> +}




[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux