Re: [PATCH v3 1/2] dt-bindings: iio: adc: adding support for PAC193X

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Nov 26, 2023 at 04:04:38PM +0000, Jonathan Cameron wrote:
> On Sun, 26 Nov 2023 11:24:56 +0000
> Conor Dooley <conor@xxxxxxxxxx> wrote:
> > On Sat, Nov 25, 2023 at 07:47:54PM +0000, Jonathan Cameron wrote:
> > > On Thu, 16 Nov 2023 18:21:33 +0000
> > > Conor Dooley <conor@xxxxxxxxxx> wrote:  
> > > > On Thu, Nov 16, 2023 at 04:01:43PM +0100, Krzysztof Kozlowski wrote:  
> > > > > On 15/11/2023 14:44, marius.cristea@xxxxxxxxxxxxx wrote:    
> > > > > > From: Marius Cristea <marius.cristea@xxxxxxxxxxxxx>  
> > > > > > +patternProperties:
> > > > > > +  "^channel@[1-4]+$":
> > > > > > +    type: object
> > > > > > +    $ref: adc.yaml
> > > > > > +    description: Represents the external channels which are connected to the ADC.
> > > > > > +
> > > > > > +    properties:
> > > > > > +      reg:
> > > > > > +        items:
> > > > > > +          minimum: 1
> > > > > > +          maximum: 4
> > > > > > +
> > > > > > +      shunt-resistor-micro-ohms:
> > > > > > +        description: |
> > > > > > +          Value in micro Ohms of the shunt resistor connected between
> > > > > > +          the SENSE+ and SENSE- inputs, across which the current is measured. Value
> > > > > > +          is needed to compute the scaling of the measured current.
> > > > > > +
> > > > > > +    required:
> > > > > > +      - reg
> > > > > > +      - shunt-resistor-micro-ohms
> > > > > > +
> > > > > > +    unevaluatedProperties: false
> > > > > > +
> > > > > > +required:
> > > > > > +  - compatible
> > > > > > +  - reg
> > > > > > +  - "#address-cells"
> > > > > > +  - "#size-cells"
> > > > > > +
> > > > > > +allOf:
> > > > > > +  - if:
> > > > > > +      properties:
> > > > > > +        compatible:
> > > > > > +          contains:
> > > > > > +            const: interrupts    
> > > > > 
> > > > > 
> > > > > I don't understand what do you want to say here. I am also 100% sure you
> > > > > did not test it on a real case (maybe example passes but nothing more).    
> > > > 
> > > > As far as I understand, the same pin on the device is used for both an
> > > > output or an input depending on the configuration. As an input, it is
> > > > the "slow-io" control, and as an output it is an interrupt.
> > > > I think Marius is trying to convey that either this pin can be in
> > > > exclusively one state or another.
> > > > 
> > > > _However_ I am not sure that that is really the right thing to do - they
> > > > might well be mutually exclusive modes, but I think the decision can be
> > > > made at runtime, rather than at devicetree creation time. Say for
> > > > example the GPIO controller this is connected to is capable of acting as
> > > > an interrupt controller. Unless I am misunderstanding the runtime
> > > > configurability of this hardware, I think it is possible to actually
> > > > provide a "slow-io-gpios" and an interrupt property & let the operating
> > > > system decide at runtime which mode it wants to work in.  
> > > 
> > > I'll admit I've long forgotten what was going on here, but based just on
> > > this bit of text I agree. There is nothing 'stopping' us having a pin
> > > uses as either / or / both interrupt and gpio.
> > > 
> > > It'll be a bit messy to support in the driver as IIRC there are some sanity
> > > checks that limit combinations on IRQs and output GPIOS.  Can't remember
> > > how bad the dance to navigate it safely is.
> > > 
> > > First version I'd just say pick one option if both are provided and
> > > don't support configuring it at runtime.  
> > 
> > Just to be clear, you are suggesting having the
> > "microchip,slow-io-gpios" and "interrupts" properties in the binding,
> > but the driver will just (for example) put that pin into alert mode
> > always & leave it there?
> 
> Yes.
> 
> > If that is what you are suggesting, that seems pragmatic to me.
> 
> If a use case to do something else comes along later, then we can
> be smarter, but I'd like to keep it simple initially at least.

Sounds good to me, thanks Jonathan. Seems like a good compromise of
depicting the hardware accurately and not overcomplicating the driver
implementation.

Marius, I completely forgot to get in touch with you about this - give
me a shout on teams if there's anything outstanding that I can help you
with.

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux