The hardware binding for i2c current monitoring device with overcurrent control. Signed-off-by: Ivan Mikhaylov <fr0st61te@xxxxxxxxx> --- .../bindings/iio/adc/maxim,max34408.yaml | 137 ++++++++++++++++++ 1 file changed, 137 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml diff --git a/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml new file mode 100644 index 000000000000..4262bedb4bfa --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/maxim,max34408.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/maxim,max34408.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Two- and four-channel current monitors with overcurrent control + +maintainers: + - Ivan Mikhaylov <fr0st61te@xxxxxxxxx> + +description: | + The MAX34408/MAX34409 are two- and four-channel current monitors that are + configured and monitored with a standard I2C/SMBus serial interface. Each + unidirectional current sensor offers precision high-side operation with a + low full-scale sense voltage. The devices automatically sequence through + two or four channels and collect the current-sense samples and average them + to reduce the effect of impulse noise. The raw ADC samples are compared to + user-programmable digital thresholds to indicate overcurrent conditions. + Overcurrent conditions trigger a hardware output to provide an immediate + indication to shut down any necessary external circuitry. + + Specifications about the devices can be found at: + https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdf + +properties: + compatible: + enum: + - maxim,max34408 + - maxim,max34409 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + isshutdown-gpios: + description: + Shutdown Output. Open-drain output. This output transitions to high impedance + when any of the digital comparator thresholds are exceeded as long as the ENA + pin is high. + maxItems: 1 + + shtdn-enable-gpios: + description: + SHTDN Enable Input. CMOS digital input. Connect to GND to clear the latch and + unconditionally deassert (force low) the SHTDN output and reset the shutdown + delay. Connect to VDD to enable normal latch operation of the SHTDN output. + maxItems: 1 + + vdd-supply: true + +required: + - compatible + - reg + +patternProperties: + "^channel@[0-3]$": + $ref: adc.yaml + type: object + description: + Represents the internal channels of the ADC. + + properties: + reg: + items: + minimum: 0 + maximum: 3 + + maxim,rsense-val-micro-ohms: + description: + Adjust the Rsense value to monitor higher or lower current levels for + input. + enum: [250, 500, 1000, 5000, 10000, 50000, 100000, 200000, 500000] + default: 1000 + + required: + - reg + - maxim,rsense-val-micro-ohms + + unevaluatedProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: maxim,max34408 + then: + patternProperties: + "^channel@[2-3]$": false + "^channel@[0-1]$": + properties: + reg: + minimum: 0 + maximum: 1 + else: + patternProperties: + "^channel@[0-3]$": + properties: + reg: + minimum: 0 + maximum: 3 + +additionalProperties: false + +examples: + - | + i2c { + + #address-cells = <1>; + #size-cells = <0>; + + adc@1e { + compatible = "maxim,max34409"; + reg = <0x1e>; + + #address-cells = <1>; + #size-cells = <0>; + channel@0 { + reg = <0x0>; + maxim,rsense-val-micro-ohms = <5000>; + }; + + channel@1 { + reg = <0x1>; + maxim,rsense-val-micro-ohms = <10000>; + }; + }; + }; -- 2.42.0
