Re: [PATCH 5/5] iio: addac: ad74413r: add support for reset-gpio

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, 11 Nov 2022 15:39:21 +0100
Rasmus Villemoes <linux@xxxxxxxxxxxxxxxxxx> wrote:

> We have a board where the reset pin of the ad74412 is connected to a
> gpio, but also pulled low by default. Hence to get the chip out of
> reset, the driver needs to know about that gpio and set it high before
> attempting to communicate with it.

I'm a little confused on polarity here.  The pin is a !reset so
we need to drive it low briefly to trigger a reset.
I'm guessing for your board the pin is set to active low? (an example
in the dt would have made that clearer) Hence the pulse
in here to 1 is actually briefly driving it low before restoring to high?

For a pin documented as !reset that seems backwards though you have
called it reset so that is fine, but this description doesn't make that
celar.

Perhaps just add some more description here to make it clear the GPIO
is active low, and then refer to setting it to true and false to avoid
the confusing high / low terminology which are inverted...

> 
> When a reset-gpio is given in device tree, use that instead of the
> software reset. According to the data sheet, the two methods are
> functionally equivalent.
> 
> Signed-off-by: Rasmus Villemoes <linux@xxxxxxxxxxxxxxxxxx>
> ---
>  drivers/iio/addac/ad74413r.c | 12 ++++++++++++
>  1 file changed, 12 insertions(+)
> 
> diff --git a/drivers/iio/addac/ad74413r.c b/drivers/iio/addac/ad74413r.c
> index 9f77d2f514de..af09d43f921c 100644
> --- a/drivers/iio/addac/ad74413r.c
> +++ b/drivers/iio/addac/ad74413r.c
> @@ -71,6 +71,7 @@ struct ad74413r_state {
>  	struct regmap			*regmap;
>  	struct device			*dev;
>  	struct iio_trigger		*trig;
> +	struct gpio_desc		*reset_gpio;
>  
>  	size_t			adc_active_channels;
>  	struct spi_message	adc_samples_msg;
> @@ -393,6 +394,13 @@ static int ad74413r_reset(struct ad74413r_state *st)
>  {
>  	int ret;
>  
> +	if (st->reset_gpio) {
> +		gpiod_set_value_cansleep(st->reset_gpio, 1);
> +		fsleep(50);
> +		gpiod_set_value_cansleep(st->reset_gpio, 0);
> +		return 0;
> +	}
> +
>  	ret = regmap_write(st->regmap, AD74413R_REG_CMD_KEY,
>  			   AD74413R_CMD_KEY_RESET1);
>  	if (ret)
> @@ -1316,6 +1324,10 @@ static int ad74413r_probe(struct spi_device *spi)
>  	if (IS_ERR(st->regmap))
>  		return PTR_ERR(st->regmap);
>  
> +	st->reset_gpio = devm_gpiod_get_optional(st->dev, "reset", GPIOD_OUT_LOW);
> +	if (IS_ERR(st->reset_gpio))
> +		return PTR_ERR(st->reset_gpio);
> +
>  	st->refin_reg = devm_regulator_get_optional(st->dev, "refin");
>  	if (IS_ERR(st->refin_reg)) {
>  		ret = PTR_ERR(st->refin_reg);




[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux