Re: [PATCH 8/9] arm64: dts: qcom: Add DTS for MSM8976 and MSM8956 SoCs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 04/11/2022 13:21, AngeloGioacchino Del Regno wrote:
> From: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxxx>
> 
> This commit adds device trees for MSM8956 and MSM8976 SoCs.
> They are *almost* identical, with minor differences, such as
> MSM8956 having two A72 cores less.
> 

Thank you for your patch. There is something to discuss/improve.

> +
> +		sdhc_1: mmc@7824000 {
> +			compatible = "qcom,msm8976-sdhci", "qcom,sdhci-msm-v4";
> +			reg = <0x07824900 0x500>, <0x07824000 0x800>;
> +			reg-names = "hc", "core";
> +
> +			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +
> +			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> +				 <&gcc GCC_SDCC1_APPS_CLK>,
> +				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
> +			clock-names = "iface", "core", "xo";
> +
> +			bus-width = <8>;
> +			non-removable;

Aren't these two depend where is eMMC and where SD? Similarly to the
node below. I wouold expect board DTS define them.

> +			status = "disabled";
> +		};
> +
> +		sdhc_2: mmc@7864000 {
> +			compatible = "qcom,msm8976-sdhci", "qcom,sdhci-msm-v4";
> +			reg = <0x07864900 0x11c>, <0x07864000 0x800>;
> +			reg-names = "hc", "core";
> +
> +			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +
> +			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
> +				 <&gcc GCC_SDCC2_APPS_CLK>,
> +				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
> +			clock-names = "iface", "core", "xo";
> +
> +			bus-width = <4>;
> +			status = "disabled";
> +		};
> +
> +		blsp1_dma: dma-controller@7884000 {
> +			compatible = "qcom,bam-v1.7.0";
> +			reg = <0x07884000 0x1f000>;
> +			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "bam_clk";
> +			#dma-cells = <1>;
> +			qcom,ee = <0>;
> +		};
> +
> +		blsp1_uart1: serial@78af000 {
> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> +			reg = <0x078af000 0x200>;
> +			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp1_dma 0>, <&blsp1_dma 1>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		blsp1_uart2: serial@78b0000 {
> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> +			reg = <0x078b0000 0x200>;
> +			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		blsp1_spi1: spi@78b5000 {
> +			compatible = "qcom,spi-qup-v2.2.1";
> +			reg = <0x078b5000 0x500>;
> +			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp1_dma 4>, <&blsp1_dma 5>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&spi1_default>;
> +			pinctrl-1 = <&spi1_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp1_i2c2: i2c@78b6000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078b6000 0x500>;
> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			clock-frequency = <400000>;
> +			dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&blsp1_i2c2_default>;
> +			pinctrl-1 = <&blsp1_i2c2_default>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp1_i2c4: i2c@78b8000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078b8000 0x500>;
> +			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			clock-frequency = <400000>;
> +			dmas = <&blsp1_dma 10>, <&blsp1_dma 11>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&blsp1_i2c4_default>;
> +			pinctrl-1 = <&blsp1_i2c4_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		otg: usb@78db000 {
> +			compatible = "qcom,ci-hdrc";
> +			reg = <0x078db000 0x200>,
> +			      <0x078db200 0x200>;
> +			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_USB_HS_AHB_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>;
> +			clock-names = "iface", "core";
> +			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
> +			assigned-clock-rates = <80000000>;
> +			resets = <&gcc RST_USB_HS_BCR>;
> +			reset-names = "core";
> +			ahb-burst-config = <0>;
> +			dr_mode = "peripheral";
> +			phy_type = "ulpi";
> +			phy-names = "usb-phy";
> +			phys = <&usb_hs_phy>;
> +			status = "disabled";
> +			#reset-cells = <1>;
> +		};
> +
> +		sdhc_3: mmc@7a24000 {
> +			compatible = "qcom,msm8976-sdhci", "qcom,sdhci-msm-v4";
> +			reg = <0x07a24900 0x11c>, <0x07a24000 0x800>;
> +			reg-names = "hc", "core";
> +
> +			interrupts = <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +
> +			clocks = <&gcc GCC_SDCC3_AHB_CLK>,
> +				 <&gcc GCC_SDCC3_APPS_CLK>,
> +				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
> +			clock-names = "iface", "core", "xo";
> +			bus-width = <4>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;

These two are needed also for the board if SDIO is attached here.

> +
> +			status = "disabled";
> +		};
> +
> +		blsp2_dma: dma-controller@7ac4000 {
> +			compatible = "qcom,bam-v1.7.0";
> +			reg = <0x07ac4000 0x1f000>;
> +			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
> +			clock-names = "bam_clk";
> +			#dma-cells = <1>;
> +			qcom,ee = <0>;
> +		};
> +
> +		blsp2_uart2: serial@7af0000 {
> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> +			reg = <0x07af0000 0x200>;
> +			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp2_dma 0>, <&blsp2_dma 1>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		blsp2_i2c2: i2c@7af6000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x07af6000 0x600>;
> +			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			clock-frequency = <400000>;
> +			dmas = <&blsp2_dma 6>, <&blsp2_dma 7>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&blsp2_i2c2_default>;
> +			pinctrl-1 = <&blsp2_i2c2_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp2_i2c4: i2c@7af8000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x07af8000 0x600>;
> +			interrupts = <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			clock-frequency = <400000>;
> +			dmas = <&blsp2_dma 10>, <&blsp2_dma 11>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&blsp2_i2c4_default>;
> +			pinctrl-1 = <&blsp2_i2c4_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		intc: interrupt-controller@b000000 {
> +			compatible = "qcom,msm-qgic2";
> +			reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +		};
> +
> +		apcs: syscon@b011000 {
> +			compatible = "syscon";

This cannot be alone, you need specific compatible.

> +			reg = <0x0b011000 0x1000>;
> +		};
> +
> +		timer@b120000 {
> +			compatible = "arm,armv7-timer-mem";
> +			reg = <0x0b120000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +			clock-frequency = <19200000>;
> +
> +			frame@b121000 {
> +				reg = <0x0b121000 0x1000>, <0x0b122000 0x1000>;
> +				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <0>;
> +			};
> +
> +			frame@b123000 {
> +				reg = <0x0b123000 0x1000>;
> +				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <1>;
> +				status = "disabled";
> +			};
> +
> +			frame@b124000 {
> +				reg = <0x0b124000 0x1000>;
> +				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <2>;
> +				status = "disabled";
> +			};
> +
> +			frame@b125000 {
> +				reg = <0x0b125000 0x1000>;
> +				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <3>;
> +				status = "disabled";
> +			};
> +
> +			frame@b126000 {
> +				reg = <0x0b126000 0x1000>;
> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <4>;
> +				status = "disabled";
> +			};
> +
> +			frame@b127000 {
> +				reg = <0x0b127000 0x1000>;
> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <5>;
> +				status = "disabled";
> +			};
> +
> +			frame@b128000 {
> +				reg = <0x0b128000 0x1000>;
> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> +				frame-number = <6>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		imem: imem@8600000 {
> +			compatible = "simple-mfd";

You need specific compatible. This is imem. I was already fixing other
boards but I think new ones appeared... so I will re-fix these.


> +			reg = <0x08600000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			ranges = <0 0x08600000 0x1000>;
> +
> +			pil-reloc@94c {
> +				compatible = "qcom,pil-reloc-info";
> +				reg = <0x94c 0xc8>;
> +			};
> +		};
> +	};
> +

Best regards,
Krzysztof




[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux