AD4130-8 is an ultra-low power, high precision, measurement solution for
low bandwidth battery operated applications.
The fully integrated AFE (Analog Front-End) includes a multiplexer for up
to 16 single-ended or 8 differential inputs, PGA (Programmable Gain
Amplifier), 24-bit Sigma-Delta ADC, on-chip reference and oscillator,
selectable filter options, smart sequencer, sensor biasing and excitation
options, diagnostics, and a FIFO buffer.
V1 -> V2
* add kernel version to ABI file
* merge ABI patch into driver patch
* make copyright header similar to other drivers
* rearrange includes
* use units.h defines where possible and add unit sufix to
SOFT_RESET_SLEEP define
* remove ending comma to last members of enums / lists
* remove unused FILTER_MAX define
* use BIT macro for PIN_FN_*
* rearrange SETUP_SIZE definition
* group bools in ad4130_state and ad4130_chan_info
* put scale_tbls definition on one line
* remove newline before reg size == 0 check
* put mask used as value in a variable
* remove useless ret = 0 assignment
* make buffer attrs oneline
* use for_each_set_bit in update_scan_mode
* use if else for internal reference voltage error checking
* inline reference voltage check
* check number of vbias pins
* remove .has_int_pin = false
* remove avail_len for IIO_AVAIL_RANGE
* remove useless enabled_channels check in unlink_slot
* remove unused AD4130_RESET_CLK_COUNT define
* only call fwnode_handle_put for child in case of error
* default adi,reference-select to REFIN1
* default adi,int-ref-en to false
* of_irq_get_byname -> fwnode_irq_get_byname
* P1 -> P2 as interrupt pin options
* add missing comma in db3_freq_avail init
* cast values to u64 to make math using units.h work
* add datasheet reference to IRQ polarity
* add comment about disabling channels in predisable
* add part number prefix find_table_index
* return voltage from get_ref_voltage
* add datasheet reference for internal reference voltage selection
* add comment explaining AIN and GPIO pin sharing
* parse channel setup before parsing excitation pins
* only validate excitation pin if value is not off
* use FIELD_PREP for bipolar and int_ref_en
* put devm_regmap_init call on one line
* introduce a slot_info struct to contain setup_info for each slot
* enable internal reference automatically if needed
* decide mclk sel based on adi,ext-clk-freq and adi,int-clk-out
* dt-bindings: use internal reference explicitly
* dt-bindings: set type for adi,excitation-pin-0
* dt-bindings: set $ref for adi,vbias-pins
* dt-bindings: remove minItems from interrupts property
* dt-bindings: remove adi,int-ref-en default value
* dt-bindings: remove adi,bipolar default value
* dt-bindings: inline adi,int-ref-en description
* dt-bindings: default adi,reference-select to REFIN1
* dt-bindings: clean up description for diff-channels and
adi,reference-select
* dt-bindings: add more text to interrupt-names description
* dt-bindings: turn interrupt-names into a single string
* dt-bindings: add maxItems to adi,vbias-pins
V2 -> V3
* dt-bindings: add interrupt controller include to example
* dt-bindings: remove $ref in diff-channels
V3 -> V4:
* handle watermark value as number of datum
* DOUT_OR_INT -> INT
* AD4130_8_NAME -> AD4130_NAME
* return early in case of failure when parsing fw channel
* use IIO_DMA_MINALIGN for aligning buffer
* add comments for fs_to_freq and freq_to_fs
* remove support for other variants because of unavailability of model
ids for future chip variants
* remove support for db3 frequency because of inaccuracy when calculating
* remove ternary where possible
* refactor defines
* dt-bindings: add unevaluatedProperties: true to channel node
V4 -> V5:
* simplify get_ref_voltage function and move print statement to first user
* inline statements not going over the 80 cols limit
* simplify scale table filling
* determine table length inside find table index macro
* current_na -> tmp inside ad4130_parse_fw_setup
* define full register set
* put range register size definitions on one line
* nanoamps -> nanoamp
* adi,ext-clk-freq -> adi,ext-clk-freq-hz
* return directly in ad4130_validate_vbias_pins
* place comment regarding irq_trigger at assignment
* inversed -> inverted inside irq_trigger comment
* do not initialize int_clk_out
* return directly in ad4130_validate_diff_channels
* add () after reference to update_scan_mode in comment
* use BIT() for channel offset
* comment nitpicks on slot finding
* return -EINVAL out of reg read for invalid sizes
* place regmap at start of ad4130_state
* place bools at the end of ad4130_setup_info
* remove commas after terminators
* dt-bindings: only allow one element in reg
* dt-bindings: inline reg description
* dt-bindings: remove $ref from adi,ext-clk-freq-hz
V5 -> V6:
* bump KernelVersion
* use IIO_DEVICE_ATTR_RO
* nitpick inside mutex comment
* use valid_mask for validating gpios
* improve DMA comment
V6 -> V7:
* remove $ref from -nanoamp properties (to be added to dtschema)
* use hexadecimal numbers for channel unit-addresses
V7 -> V8:
* pick up Reviewed-By tags
* bump KernelVersion
V8 -> V9:
* bump KernelVersion
* enable internal clock output via CCF
* remove unused AD4130_MCLK_SEL_MAX
* remove unused AD4130_STATUS_POR_FLAG_MASK
* remove unused ad4130_id
* remove double new line
V9 -> V10:
* Fix unsafe buffer attributes
* fix KernelVersion indent
* bump KernelVersion
* handle null of_node
* depend on COMMON_CLK
* dt-bindings: make sure minItems is not equal to maxItems
* dt-bindings: add clock provider properties
* add ABI to MAINTAINERS
Cosmin Tanislav (2):
dt-bindings: iio: adc: add AD4130
iio: adc: ad4130: add AD4130 driver
.../ABI/testing/sysfs-bus-iio-adc-ad4130 | 36 +
.../bindings/iio/adc/adi,ad4130.yaml | 259 ++
MAINTAINERS | 9 +
drivers/iio/adc/Kconfig | 14 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/ad4130.c | 2100 +++++++++++++++++
6 files changed, 2419 insertions(+)
create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-adc-ad4130
create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad4130.yaml
create mode 100644 drivers/iio/adc/ad4130.c
--
2.38.1
