On Mon, Oct 17, 2022 at 07:06:26PM +0200, Kamel Bouhara wrote:
> On Mon, Oct 17, 2022 at 08:53:18AM -0400, William Breathitt Gray wrote:
> > On Mon, Oct 17, 2022 at 11:59:37AM +0200, Kamel Bouhara wrote:
> > > On Sat, Oct 15, 2022 at 09:52:27AM -0400, William Breathitt Gray wrote:
> > > > I was looking over the microchip-tcb-capture driver recently and noticed
> > > > that the code doesn't seem to account for Signal1. In particular, it
> > > > appears that mchp_tc_count_signal_read() and mchp_tc_count_action_read()
> > > > don't check the Signal id at all and just assume they are handling
> > > > Signal0. This creates a situation where the information returned for the
> > > > Signal1 sysfs attributes are just duplicated reports of Signal0.
> > > >
> > > > What exactly is the relationship of Signal0 ("Channel A") and Signal1
> > > > ("Channel B"); is SignalB only relevant when the counter device is
> > > > configured for quadrature mode?
> > >
> > > Indeed both signals are required when in quadrature mode, where the
> > > signal0 is representing the speed and signal1 the revolution or number
> > > of rotation.
> > >
> > > We have described all availables modes in details in the following blog post: https://bootlin.com/blog/timer-counters-linux-microchip/
> > >
> > > Regards,
> > > Kamel
> >
> > Thank you for the link, the block diagram helps illustrate how the
> > signals correlate to the TCB channels.
> >
> > Let me check if I understand correctly. In microchip-tcb-capture.c,
> > mchp_tc_count_signals[0] is TIOA0 while mchp_tc_count_signals[1] is
> > TIOB0? In quadrature mode, are TIOA and TIOB the two phases of a
> > quadrature encoder? You mentioned one signal is speed while the other is
> > the number of rotations; does this mean one signal serves as the
> > position incrementation from a rotary wheel while the other signal is
> > the index (z-phase) indicate for each full rotation?
> >
>
> IIRC this is indeed both signal edges (phase A and B) are accumulated on
> channel 0 and channel 1 stores the revolution or number of rotation of
> the qdec encoder.
Ah, I think I understand now: Signal0 and Signal1 are TIOA and TIOB
respectively; channel 0 and channel 1 are data registers; channel 0
holds the Count0 count value; channel 1 holds the revolution value (but
the microchip-tcb-capture driver does not expose it).
It might be nice to expose the channel 1 revolution value as Count1 at
some point in the future. However, channel 1 seems unrelated to the
current issue we're dicussing so we can avoid it for now.
> > In particular, I'm having trouble understanding
> > mchp_tc_count_signal_read(). I suspect it is unintentionally always
> > returning the signal status for TIOA::
> >
> > regmap_read(priv->regmap, ATMEL_TC_REG(priv->channel[0], SR), &sr);
> >
> > if (priv->trig_inverted)
> > sigstatus = (sr & ATMEL_TC_MTIOB);
> > else
> > sigstatus = (sr & ATMEL_TC_MTIOA);
> >
> > *lvl = sigstatus ? COUNTER_SIGNAL_LEVEL_HIGH : COUNTER_SIGNAL_LEVEL_LOW;
> >
> > Here we read the status register for channel 0, select between TIOA and
> > TIOB based on priv->trig_inverted, and then return the signal level.
> >
> > I don't see priv->trig_inverted referenced anywhere else so it appears
> > that priv->trig_inverted will always be 0, thus resulting in
> > mchp_tc_count_signal_read() always returning the TIOA status. I think
> > the intended behavior is to return the status of the selected signal::
>
> IIRC the trig_inverted shall be used when signals are inverted which
> means we read position on TIOB and revolution on TIOA.
Sure, that seems like a reasonable option to expose, but it does not
appear that trig_inverted is being set or otherwise configured in the
current code, unless I'm missing something. It might be best to remove
trig_inverted if the functionality is not supported yet by this driver.
> >
> > if (signal->id == 1)
> > sigstatus = (sr & ATMEL_TC_MTIOB);
> > else
> > sigstatus = (sr & ATMEL_TC_MTIOA);
> >
> > As for mchp_tc_count_action_read(), we have a similar problem: no
> > distinction is made for the Synapse requested. The channel mode register
> > for channel 0 is read and then masked against ATMEL_TC_ETRGEDG to
> > determine the action mode. It appears that this code is always assuming
> > the Synapse for TIOA is requested, but the Synapse for TIOB could be
> > passed. You can determine which corresponding Signal you have by
> > checking synapse->signal->id before deciding what action mode to return.
> >
>
> That is indeed a good point as both signals are eligible to trigger the
> TC for both modes (capture/qdec).
>
> > To clarify, in COUNTER_FUNCTION_INCREASE mode, does the Count value
> > increment based on the edge of TIOA and not TIOB? In
>
> Yes, currently the driver only support TIOA.
>
> > COUNTER_FUNCTION_QUADRATURE_X4 mode, does the Count value increment
> > based on both edges of TIOA and TIOB serving as quadrature encoding
> > phase A and B signals?
>
> Yes as explained above.
Okay this should be simple to resolve then: return -EINVAL if Synapse is
for TIOB in mchp_tc_count_action_write(), and pass back
COUNTER_SYNAPSE_ACTION_NONE for TIOB during non-quadrature mode in
mchp_tc_counter_action_read().
I'll submit a patch fixing these changes and the signal_read() callback
mentioned previously.
By the way, I suspect there are race conditions present in
mcho_tc_count_function_write() that could be resolved by adding a lock
to the mchp_tc_data structure and acquiring it before accessing the
device state and registers. It's unrelated to the Signal1 issues so I
haven't looked any further into it, but it's something you might want to
investigate to make sure you don't get weird behavior from the driver.
Thanks,
William Breathitt Gray
Attachment:
signature.asc
Description: PGP signature
