Hi William Breathitt Gray,
Thanks for the feedback.
> Subject: Re: [PATCH RFC 0/8] Add RZ/G2L MTU3a MFD and Counter driver
>
> On Wed, Sep 28, 2022 at 06:14:57AM +0000, Biju Das wrote:
> > Hi William Breathitt Gray,
> >
> > Thanks for the feedback.
> >
> > > Subject: Re: [PATCH RFC 0/8] Add RZ/G2L MTU3a MFD and Counter
> driver
> > >
> > > On Mon, Sep 26, 2022 at 02:21:06PM +0100, Biju Das wrote:
> > > > The RZ/G2L multi-function timer pulse unit 3 (MTU3a) is embedded
> > > > in the Renesas RZ/G2L family SoC's. It consists of eight 16-bit
> > > > timer channels and one 32-bit timer channel. It supports the
> > > > following functions
> > > > - Counter
> > > > - Timer
> > > > - PWM
> > > >
> > > > This patch series aim to add MFD and counter driver for MTU3a.
> > > > Subsequent patch seies will add TImer and PWM driver support
> also
> > > > enhancements to counter driver.
> > >
> > > Hello Biju,
> > >
> > > I see this device consists of several channels, but only one Count
> > > is defined in the counter patch ("Channel 1 Count"). Do all
> channels
> > > support counting, or is it limited to just one channel?
> >
> > It is like this
> > MTU1 channel :- 1 16-bit phase counter MTU2-Channel :- 1 16-bit
> phase
> > counter
> > MTU1 + MTU2 channel combined:- 1 32-bit phase counter Other channels
> > are not supporting phase counting.
> >
> > Each counter device will have 1 channel. Currently it supports 16-
> bit
> > phase counting.
> >
> > Please see my test program. Am I missing something here?
> >
> > My test program:-
> >
> > echo 1 > /sys/bus/counter/devices/counter0/count0/enable
> > echo 50 > /sys/bus/counter/devices/counter0/count0/ceiling
> > devmem2 0x10001391 b 0x00 # Enable phase clock selection A for MTU2.
> > echo 1 > /sys/bus/counter/devices/counter1/count0/enable
> > echo 50 > /sys/bus/counter/devices/counter1/count0/ceiling
> >
> > for i in {1..5};
> > do cat /sys/bus/counter/devices/counter0/count0/count ; cat
> > /sys/bus/counter/devices/counter0/count0/direction;
> > cat /sys/bus/counter/devices/counter1/count0/count;
> > cat /sys/bus/counter/devices/counter1/count0/direction;
> > done
> >
> > Cheers,
> > Biju
>
> I'm not familiar with this hardware, but it looks like MTU1 and MTU2
> are on the same device. I think a more natural way to expose this
> functionality in the Counter subsystem would be to define a Count for
> each count value you can support; so something like this (all under
> /sys/bus/counter/devices/counter0):
>
> * count0 :- MTU1
> * count1 :- MTU2
> * count3 :- MTU1 + MTU2
OK, sounds good. so count3 :- 32 bit phase counting
count 0 or count1 or both then 16 bit phase counting
>
> You can then control the phase selection using a top-level Counter
> device extension (e.g. /sys/bus/counter/devices/counter0/phase) that
> configures whether you're in 16-bit phase or 32-phase counting mode.
So I need to introduce a new sysfs called phase. Use that one for
Selecting the external clock pin for phase counting mode.
Please correct me if I am wrong??
Hardware supports 4 pins for phase counting mode,
MTCLKA Input External clock A input pin (MTU1/MTU2 phase counting mode A phase input)
MTCLKB Input External clock B input pin (MTU1/MTU2 phase counting mode B phase input)
MTCLKC Input External clock C input pin (MTU2 phase counting mode A phase input)
MTCLKD Input External clock D input pin (MTU2 phase counting mode B phase input)
For MTU1, it is fixed MTCLKA and MTCLKB.
But for MTU2, it can be either 0-{ MTCLKA, MTCLKB} or 1 - { MTCLKC , MTCLKD}
On reset it is set to { MTCLKC , MTCLKD}.
Cheers,
Biju
