PMP8074 is a companion PMIC to the Qualcomm IPQ8074 series that is
controlled via SPMI.
Add DTSI for it providing GPIO, regulator and RTC support.
RTC is disabled by default as there is no built-in battery so it will
loose time unless board vendor added a battery, so make it optional.
Signed-off-by: Robert Marko <robimarko@xxxxxxxxx>
---
Changes in v6:
* Add RTC and GPIO nodes
Changes in v5:
* Remove #address-cells and #size-cells as they are not required for
regulator subnodes
---
arch/arm64/boot/dts/qcom/pmp8074.dtsi | 125 ++++++++++++++++++++++++++
1 file changed, 125 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pmp8074.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pmp8074.dtsi b/arch/arm64/boot/dts/qcom/pmp8074.dtsi
new file mode 100644
index 000000000000..a3b395e4d78f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmp8074.dtsi
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+&spmi_bus {
+ pmic@0 {
+ compatible = "qcom,pmp8074", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmp8074_adc: adc@3100 {
+ compatible = "qcom,spmi-adc-rev2";
+ reg = <0x3100>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+
+ ref_gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ vref_1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ vref_vadc@2 {
+ reg = <ADC5_VREF_VADC>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ pmic_die: die_temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ xo_therm: xo_temp@76 {
+ reg = <ADC5_XO_THERM_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ pa_therm1: thermistor1@77 {
+ reg = <ADC5_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ pa_therm2: thermistor2@78 {
+ reg = <ADC5_AMUX_THM2_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ pa_therm3: thermistor3@79 {
+ reg = <ADC5_AMUX_THM3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ vph_pwr@131 {
+ reg = <ADC5_VPH_PWR>;
+ qcom,pre-scaling = <1 3>;
+ };
+ };
+
+ pmp8074_rtc: rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+ allow-set-time;
+ status = "disabled";
+ };
+
+ pmp8074_gpios: gpio@c000 {
+ compatible = "qcom,pmp8074-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmp8074_gpios 0 0 12>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmic@1 {
+ compatible = "qcom,pmp8074", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+
+ regulators {
+ compatible = "qcom,pmp8074-regulators";
+
+ s3: s3 {
+ regulator-name = "vdd_s3";
+ regulator-min-microvolt = <592000>;
+ regulator-max-microvolt = <1064000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ s4: s4 {
+ regulator-name = "vdd_s4";
+ regulator-min-microvolt = <712000>;
+ regulator-max-microvolt = <992000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l11: l11 {
+ regulator-name = "l11";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+};
--
2.36.1
