On Sat, 12 Mar 2022 00:46:27 +0800
Cixi Geng <gengcixi@xxxxxxxxx> wrote:
> From: Cixi Geng <cixi.geng1@xxxxxxxxxx>
>
> The ump9620 is variant from sc27xx chip, add it in here.
>
> Signed-off-by: Yuming Zhu <yuming.zhu1@xxxxxxxxxx>
> Signed-off-by: Cixi Geng <cixi.geng1@xxxxxxxxxx>
Hi,
Same comments as made earlier apply here.
* Should there be a co-developed-by marking here or should
the from reflect Yuming Zhu as the patch author with you in
the role of being on the path to upstream?
* change log below the ---
* No blank lines or non tag lines in the tag block - use
comments at the end of the lines if you want to give
reported-by for particularly things.
Also, I'm not immediately spotting where Baolin gave
a tag.
Comments inline.
There are a few places in here where you have significant deviation between
the code that runs for this new device and previously supported parts.
Doing that via if / else tends not to scale as yet more parts are added in
future. Perhaps it would be better to move to some device type specific
callbacks for more of these cases. This would be similar to the init_scale
and get_ratio function pointers you already have in the variant data.
Thanks,
Jonathan
>
> V2 changes:
> 1. remove duplicated function
> Reviewed-by: Baolin Wang <baolin.wang7@xxxxxxxxx>
>
> 2. fix the smatch warnings
> Reported-by: kernel test robot <lkp@xxxxxxxxx>
> Reported-by: Dan Carpenter <dan.carpenter@xxxxxxxxxx>
> ---
> drivers/iio/adc/sc27xx_adc.c | 305 ++++++++++++++++++++++++++++++-----
> 1 file changed, 266 insertions(+), 39 deletions(-)
>
> diff --git a/drivers/iio/adc/sc27xx_adc.c b/drivers/iio/adc/sc27xx_adc.c
> index b89637c051ac..e9b680e9c275 100644
> --- a/drivers/iio/adc/sc27xx_adc.c
> +++ b/drivers/iio/adc/sc27xx_adc.c
> @@ -15,12 +15,16 @@
> /* PMIC global registers definition */
> #define SC2730_MODULE_EN 0x1808
> #define SC2731_MODULE_EN 0xc08
> +#define UMP9620_MODULE_EN 0x2008
> #define SC27XX_MODULE_ADC_EN BIT(5)
> #define SC2721_ARM_CLK_EN 0xc0c
> #define SC2730_ARM_CLK_EN 0x180c
> #define SC2731_ARM_CLK_EN 0xc10
> +#define UMP9620_ARM_CLK_EN 0x200c
> +#define UMP9620_XTL_WAIT_CTRL0 0x2378
> #define SC27XX_CLK_ADC_EN BIT(5)
> #define SC27XX_CLK_ADC_CLK_EN BIT(6)
> +#define UMP9620_XTL_WAIT_CTRL0_EN BIT(8)
>
> /* ADC controller registers definition */
> #define SC27XX_ADC_CTL 0x0
> @@ -82,6 +86,13 @@
> enum sc27xx_pmic_type {
> SC27XX_ADC,
> SC2721_ADC,
> + UMP9620_ADC,
> +};
> +
> +enum ump96xx_scale_cal {
> + UMP96XX_VBAT_SENSES_CAL,
> + UMP96XX_VBAT_DET_CAL,
> + UMP96XX_CH1_CAL,
> };
>
> struct sc27xx_adc_data {
> @@ -139,6 +150,11 @@ static struct sc27xx_adc_linear_graph small_scale_graph = {
> 100, 341,
> };
>
> +static struct sc27xx_adc_linear_graph ump9620_bat_det_graph = {
> + 1400, 3482,
> + 200, 476,
> +};
> +
> /* Add these for sc2731 pmic, and the [big|small]_scale_graph_calib for common's */
> static const struct sc27xx_adc_linear_graph sc2731_big_scale_graph_calib = {
> 4200, 850,
> @@ -165,16 +181,41 @@ static int sc27xx_adc_get_calib_data(u32 calib_data, int calib_adc)
> return ((calib_data & 0xff) + calib_adc - 128) * 4;
> }
>
> +/* get the adc nvmem cell calibration data */
> +static int adc_nvmem_cell_calib_data(struct sc27xx_adc_data *data, const char *cell_name)
> +{
This looks to be a bit of refactoring that could be sensibly pulled out before this
patch.
> + struct nvmem_cell *cell;
> + void *buf;
> + u32 origin_calib_data = 0;
Why initialise the above? I don't see it being used
in any paths where it isn't already initialised.
> + size_t len = 0;
> +
> + if (!data)
> + return -EINVAL;
> +
> + cell = nvmem_cell_get(data->dev, cell_name);
> + if (IS_ERR(cell))
> + return PTR_ERR(cell);
> +
> + buf = nvmem_cell_read(cell, &len);
> + if (IS_ERR(buf)) {
> + nvmem_cell_put(cell);
> + return PTR_ERR(buf);
> + }
> +
> + memcpy(&origin_calib_data, buf, min(len, sizeof(u32)));
> +
> + kfree(buf);
> + nvmem_cell_put(cell);
> + return origin_calib_data;
> +}
> +
> static int sc27xx_adc_scale_calibration(struct sc27xx_adc_data *data,
> bool big_scale)
> {
> const struct sc27xx_adc_linear_graph *calib_graph;
> struct sc27xx_adc_linear_graph *graph;
> - struct nvmem_cell *cell;
> const char *cell_name;
> u32 calib_data = 0;
> - void *buf;
> - size_t len;
>
> if (big_scale) {
> calib_graph = data->var_data->bscale_cal;
> @@ -186,24 +227,63 @@ static int sc27xx_adc_scale_calibration(struct sc27xx_adc_data *data,
> cell_name = "small_scale_calib";
> }
>
> - cell = nvmem_cell_get(data->dev, cell_name);
> - if (IS_ERR(cell))
> - return PTR_ERR(cell);
> -
> - buf = nvmem_cell_read(cell, &len);
> - nvmem_cell_put(cell);
> -
> - if (IS_ERR(buf))
> - return PTR_ERR(buf);
> -
> - memcpy(&calib_data, buf, min(len, sizeof(u32)));
> + calib_data = adc_nvmem_cell_calib_data(data, cell_name);
>
> /* Only need to calibrate the adc values in the linear graph. */
> graph->adc0 = sc27xx_adc_get_calib_data(calib_data, calib_graph->adc0);
> graph->adc1 = sc27xx_adc_get_calib_data(calib_data >> 8,
> calib_graph->adc1);
>
> - kfree(buf);
> + return 0;
> +}
> +
> +static int ump96xx_adc_scale_cal(struct sc27xx_adc_data *data,
> + enum ump96xx_scale_cal cal_type)
> +{
> + struct sc27xx_adc_linear_graph *graph = NULL;
Always set below, so don't initialize here. Same for other
local variables.
> + const char *cell_name1 = NULL, *cell_name2 = NULL;
> + int adc_calib_data1 = 0, adc_calib_data2 = 0;
> +
> + if (!data)
> + return -EINVAL;
> +
> + if (cal_type == UMP96XX_VBAT_DET_CAL) {
> + graph = &ump9620_bat_det_graph;
> + cell_name1 = "vbat_det_cal1";
> + cell_name2 = "vbat_det_cal2";
> + } else if (cal_type == UMP96XX_VBAT_SENSES_CAL) {
> + graph = &big_scale_graph;
> + cell_name1 = "big_scale_calib1";
> + cell_name2 = "big_scale_calib2";
> + } else if (cal_type == UMP96XX_CH1_CAL) {
> + graph = &small_scale_graph;
> + cell_name1 = "small_scale_calib1";
> + cell_name2 = "small_scale_calib2";
> + } else {
> + graph = &small_scale_graph;
> + cell_name1 = "small_scale_calib1";
> + cell_name2 = "small_scale_calib2";
> + }
> +
> + adc_calib_data1 = adc_nvmem_cell_calib_data(data, cell_name1);
> + if (adc_calib_data1 < 0) {
> + dev_err(data->dev, "err! %s:%d\n", cell_name1, adc_calib_data1);
> + return adc_calib_data1;
> + }
> +
> + adc_calib_data2 = adc_nvmem_cell_calib_data(data, cell_name2);
> + if (adc_calib_data2 < 0) {
> + dev_err(data->dev, "err! %s:%d\n", cell_name2, adc_calib_data2);
> + return adc_calib_data2;
> + }
> +
> + /*
> + *Read the data in the two blocks of efuse and convert them into the
> + *calibration value in the ump9620 adc linear graph.
> + */
> + graph->adc0 = (adc_calib_data1 & 0xfff0) >> 4;
> + graph->adc1 = (adc_calib_data2 & 0xfff0) >> 4;
> +
> return 0;
> }
>
> @@ -394,6 +474,50 @@ static int sc2731_adc_get_ratio(int channel, int scale)
> return SC27XX_VOLT_RATIO(1, 1);
> }
>
> +static int ump9620_adc_get_ratio(int channel, int scale)
> +{
> + switch (channel) {
> + case 11:
> + return SC27XX_VOLT_RATIO(1, 1);
> + case 14:
> + switch (scale) {
> + case 0:
> + return SC27XX_VOLT_RATIO(68, 900);
> + default:
> + return SC27XX_VOLT_RATIO(1, 1);
> + }
> + case 15:
> + switch (scale) {
> + case 0:
> + return SC27XX_VOLT_RATIO(1, 3);
> + default:
> + return SC27XX_VOLT_RATIO(1, 1);
> + }
> + case 21:
> + case 22:
> + case 23:
> + switch (scale) {
> + case 0:
> + return SC27XX_VOLT_RATIO(3, 8);
> + default:
> + return SC27XX_VOLT_RATIO(1, 1);
> + }
> + default:
> + switch (scale) {
> + case 0:
> + return SC27XX_VOLT_RATIO(1, 1);
> + case 1:
> + return SC27XX_VOLT_RATIO(1000, 1955);
> + case 2:
> + return SC27XX_VOLT_RATIO(1000, 2600);
> + case 3:
> + return SC27XX_VOLT_RATIO(1000, 4060);
> + default:
> + return SC27XX_VOLT_RATIO(1, 1);
> + }
> + }
> +}
> +
> /*
> * According to the datasheet set specific value on some channel.
> */
> @@ -453,6 +577,22 @@ static void sc2731_adc_scale_init(struct sc27xx_adc_data *data)
> }
> }
>
> +static void ump9620_adc_scale_init(struct sc27xx_adc_data *data)
> +{
> + int i;
> +
> + for (i = 0; i < SC27XX_ADC_CHANNEL_MAX; i++) {
> + if (i == 10 || i == 19 || i == 30 || i == 31)
> + data->channel_scale[i] = 3;
> + else if (i == 7 || i == 9)
> + data->channel_scale[i] = 2;
> + else if (i == 0 || i == 13)
> + data->channel_scale[i] = 1;
> + else
> + data->channel_scale[i] = 0;
> + }
> +}
> +
> static int sc27xx_adc_read(struct sc27xx_adc_data *data, int channel,
> int scale, int *val)
> {
> @@ -567,7 +707,7 @@ static void sc27xx_adc_volt_ratio(struct sc27xx_adc_data *data,
> *div_denominator = ratio & SC27XX_RATIO_DENOMINATOR_MASK;
> }
>
> -static int sc27xx_adc_to_volt(struct sc27xx_adc_linear_graph *graph,
> +static int adc_to_volt(struct sc27xx_adc_linear_graph *graph,
> int raw_adc)
> {
> int tmp;
> @@ -576,6 +716,31 @@ static int sc27xx_adc_to_volt(struct sc27xx_adc_linear_graph *graph,
> tmp /= (graph->adc0 - graph->adc1);
> tmp += graph->volt1;
>
> + return tmp;
> +}
> +
> +static int sc27xx_adc_to_volt(struct sc27xx_adc_linear_graph *graph,
> + int raw_adc)
> +{
> + int tmp;
> +
> + tmp = adc_to_volt(graph, raw_adc);
> +
> + return tmp < 0 ? 0 : tmp;
> +}
> +
> +static int ump96xx_adc_to_volt(struct sc27xx_adc_linear_graph *graph, int scale,
> + int raw_adc)
> +{
> + int tmp;
> +
> + tmp = adc_to_volt(graph, raw_adc);
> +
> + if (scale == 2)
> + tmp = tmp * 2600 / 1000;
> + else if (scale == 3)
> + tmp = tmp * 4060 / 1000;
> +
> return tmp < 0 ? 0 : tmp;
> }
>
> @@ -585,23 +750,46 @@ static int sc27xx_adc_convert_volt(struct sc27xx_adc_data *data, int channel,
> u32 numerator, denominator;
> u32 volt;
>
> - /*
> - * Convert ADC values to voltage values according to the linear graph,
> - * and channel 5 and channel 1 has been calibrated, so we can just
> - * return the voltage values calculated by the linear graph. But other
> - * channels need be calculated to the real voltage values with the
> - * voltage ratio.
> - */
> - switch (channel) {
> - case 5:
> - return sc27xx_adc_to_volt(&big_scale_graph, raw_adc);
> + if (data->var_data->pmic_type == UMP9620_ADC) {
> + switch (channel) {
> + case 0:
> + if (scale == 1)
> + volt = sc27xx_adc_to_volt(&ump9620_bat_det_graph, raw_adc);
> + else
> + volt = ump96xx_adc_to_volt(&small_scale_graph, scale, raw_adc);
> + break;
> + case 11:
> + volt = sc27xx_adc_to_volt(&big_scale_graph, raw_adc);
> + break;
> + default:
> + if (scale == 1)
> + volt = sc27xx_adc_to_volt(&ump9620_bat_det_graph, raw_adc);
> + else
> + volt = ump96xx_adc_to_volt(&small_scale_graph, scale, raw_adc);
> + break;
> + }
>
> - case 1:
> - return sc27xx_adc_to_volt(&small_scale_graph, raw_adc);
> + if (channel == 0 && scale == 1)
> + return volt;
> + } else {
> + /*
> + * Convert ADC values to voltage values according to the linear graph,
> + * and channel 5 and channel 1 has been calibrated, so we can just
> + * return the voltage values calculated by the linear graph. But other
> + * channels need be calculated to the real voltage values with the
> + * voltage ratio.
> + */
> + switch (channel) {
> + case 5:
> + return sc27xx_adc_to_volt(&big_scale_graph, raw_adc);
>
> - default:
> - volt = sc27xx_adc_to_volt(&small_scale_graph, raw_adc);
> - break;
> + case 1:
> + return sc27xx_adc_to_volt(&small_scale_graph, raw_adc);
> +
> + default:
> + volt = sc27xx_adc_to_volt(&small_scale_graph, raw_adc);
> + break;
> + }
> }
>
> sc27xx_adc_volt_ratio(data, channel, scale, &numerator, &denominator);
> @@ -619,6 +807,7 @@ static int sc27xx_adc_read_processed(struct sc27xx_adc_data *data,
> return ret;
>
> *val = sc27xx_adc_convert_volt(data, channel, scale, raw_adc);
> +
> return 0;
> }
>
> @@ -736,21 +925,42 @@ static int sc27xx_adc_enable(struct sc27xx_adc_data *data)
> if (ret)
> return ret;
>
> - /* Enable ADC work clock and controller clock */
> + /* Enable 26MHz crvstal oscillator wait cycles for UMP9620 ADC */
> + if (data->var_data->pmic_type == UMP9620_ADC) {
> + ret = regmap_update_bits(data->regmap, UMP9620_XTL_WAIT_CTRL0,
> + UMP9620_XTL_WAIT_CTRL0_EN,
> + UMP9620_XTL_WAIT_CTRL0_EN);
> + }
> +
> + /* Enable ADC work clock */
> ret = regmap_update_bits(data->regmap, data->var_data->clk_en,
> SC27XX_CLK_ADC_EN | SC27XX_CLK_ADC_CLK_EN,
> SC27XX_CLK_ADC_EN | SC27XX_CLK_ADC_CLK_EN);
> if (ret)
> goto disable_adc;
>
> - /* ADC channel scales' calibration from nvmem device */
> - ret = sc27xx_adc_scale_calibration(data, true);
> - if (ret)
> - goto disable_clk;
> + /* ADC channel scales calibration from nvmem device */
> + if (data->var_data->pmic_type == UMP9620_ADC) {
> + ret = ump96xx_adc_scale_cal(data, UMP96XX_VBAT_SENSES_CAL);
> + if (ret)
> + goto disable_clk;
>
> - ret = sc27xx_adc_scale_calibration(data, false);
> - if (ret)
> - goto disable_clk;
> + ret = ump96xx_adc_scale_cal(data, UMP96XX_VBAT_DET_CAL);
> + if (ret)
> + goto disable_clk;
> +
> + ret = ump96xx_adc_scale_cal(data, UMP96XX_CH1_CAL);
> + if (ret)
> + goto disable_clk;
> + } else {
> + ret = sc27xx_adc_scale_calibration(data, true);
> + if (ret)
> + goto disable_clk;
> +
> + ret = sc27xx_adc_scale_calibration(data, false);
> + if (ret)
> + goto disable_clk;
> + }
>
> return 0;
>
> @@ -774,6 +984,10 @@ static void sc27xx_adc_disable(void *_data)
>
> regmap_update_bits(data->regmap, data->var_data->module_en,
> SC27XX_MODULE_ADC_EN, 0);
> +
> + if (data->var_data->pmic_type == UMP9620_ADC)
> + regmap_update_bits(data->regmap, UMP9620_XTL_WAIT_CTRL0,
> + UMP9620_XTL_WAIT_CTRL0_EN, 0);
> }
>
> static const struct sc27xx_adc_variant_data sc2731_data = {
> @@ -824,6 +1038,18 @@ static const struct sc27xx_adc_variant_data sc2720_data = {
> .get_ratio = sc2720_adc_get_ratio,
> };
>
> +static const struct sc27xx_adc_variant_data ump9620_data = {
> + .pmic_type = UMP9620_ADC,
> + .module_en = UMP9620_MODULE_EN,
> + .clk_en = UMP9620_ARM_CLK_EN,
> + .scale_shift = SC27XX_ADC_SCALE_SHIFT,
> + .scale_mask = SC27XX_ADC_SCALE_MASK,
> + .bscale_cal = &big_scale_graph,
> + .sscale_cal = &small_scale_graph,
> + .init_scale = ump9620_adc_scale_init,
> + .get_ratio = ump9620_adc_get_ratio,
> +};
> +
> static int sc27xx_adc_probe(struct platform_device *pdev)
> {
> struct device *dev = &pdev->dev;
> @@ -917,6 +1143,7 @@ static const struct of_device_id sc27xx_adc_of_match[] = {
> { .compatible = "sprd,sc2730-adc", .data = &sc2730_data},
> { .compatible = "sprd,sc2721-adc", .data = &sc2721_data},
> { .compatible = "sprd,sc2720-adc", .data = &sc2720_data},
> + { .compatible = "sprd,ump9620-adc", .data = &ump9620_data},
> { }
> };
> MODULE_DEVICE_TABLE(of, sc27xx_adc_of_match);
