On Mon, 6 Dec 2021 13:24:18 -0600
David Lechner <david@xxxxxxxxxxxxxx> wrote:
On 11/24/21 7:58 PM, William Breathitt Gray wrote:
On Wed, Nov 24, 2021 at 08:27:20AM +0100, Oleksij Rempel wrote:
Hi William,
On Wed, Nov 24, 2021 at 03:09:05PM +0900, William Breathitt Gray wrote:
On Tue, Nov 23, 2021 at 02:45:40PM +0100, Oleksij Rempel wrote:
Add counter_push_event() to notify user space about new pulses
Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
---
drivers/counter/interrupt-cnt.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/counter/interrupt-cnt.c b/drivers/counter/interrupt-cnt.c
index 8514a87fcbee..b237137b552b 100644
--- a/drivers/counter/interrupt-cnt.c
+++ b/drivers/counter/interrupt-cnt.c
@@ -31,6 +31,8 @@ static irqreturn_t interrupt_cnt_isr(int irq, void *dev_id)
atomic_inc(&priv->count);
+ counter_push_event(&priv->counter, COUNTER_EVENT_OVERFLOW, 0);
+
return IRQ_HANDLED;
}
--
2.30.2
Hi Oleksij,
It looks like this is pushing a COUNTER_EVENT_OVERFLOW event every time
an interrupt is handled, which I suspect is not what you want to happen.
The COUNTER_EVENT_OVERFLOW event indicates a count value overflow event,
so you'll need to check for a count value overflow before pushing the
event.
It would be good idea to implement a ceiling extension as well (you can
use the COUNTER_COMP_CEILING() macro) so that users can configure the
particular point where the value overflows.
Thank you!
What would be the best and resource effective strategy for periodically
getting frequency of interrupts/pulses? This is actual information which is
needed for my use case.
So far, I was pushing every event to the user space, which is working
but probably not the most resource effective method of doing it.
Regards,
Oleskij
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
We could introduce a new Counter change-of-state event type which would
trigger whenever the count value changes, but I agree with you that this
is likely not the best way for us to derive the frequency of the
interrupts due to the indirection of handling and parsing the event
data.
Instead, perhaps introducing a "frequency" or "period" Count extension
would make more sense here. This extension could report the value delta
between counts, or alternatively the time delta from which you can
derive frequency. Regarding implementation, you can store the previous
value in a variable, updating it whenever an interrupt occurs, and
compute the particular delta every time a read is requested by the user.
David Lechner is implementing something similar for the TI eQEP driver
to expose speed, so I'm CCing them here in case this is of interest to
them.
Based on my experience, I would recommend that counter drivers be as
"thin" as possible. They shouldn't try to provide any information that
the hardware itself doesn't provide. In other words, the kernel should
provide userspace the information needed to calculate the speed/rate
but not try to do the actual calculation in the kernel. Inevitably
there are nuances for specific use cases that can't all possibly be
handled by such an implementation.
I completely agree with this. While interrupts aren't really meant for
measuring frequency, and this being somewhat of a mis-use of something, it is
still possible to do and very useful in many cases. That said, while the
counter framework is AFAIK the best fit for this, the main use-case for this
driver is measuring wheel speed (and similar "speeds"). For this, the minimum
amount of information the driver needs to provide user-space with to do
reliable calculations, is high-resolution time-stamps of GPIO events. A simple
counter is not suited, because there can be glitches that need to be detected.
If user-space gets a buffer full of consecutive time-stamps (don't need to be
all of them, just a sample of n consecutive timestamps), as well as total
count, all needed calculations, glitch filtering, low-pass filtering, etc...
can be done in user-space just fine.
I've tried using gpio interrupts to try to calculate speed/rate in
the kernel before and it simply doesn't work reliably. Interrupts
get missed and the calculation will be off.
Exactly. Been there, done that.
For reliable speed calculations of a mechanical system, the properties of the
mechanical system need to be known, like physical limits of accelerations,
maximum (or minimum) speed, etc. The minimum set of input data needed by a
user-space application to do these calculations is total pulse count in
addition to a buffer of timestamps of n consecutive input events (raising or
falling edges on GPIO). So IMHO this is what the driver should provide, and
in the most resource-efficient way possible. This particular driver will be
used 3 times on the same SoC, with each up to 10-15k pulses per second. That
is a lot of interrupts for an embedded system, so they better consume as
little resources as possible. Filling a ring buffer with timestamps should be
possible, as long as no locking is involved. Locks in IRQ context must be
avoided at all costs, specially in this case.
For really slow counts (i.e. 1 count/second), I can see a use for
generating an event on each count though. For high rates, I would
just read the count every 100ms in usespace and divide the change in
the number of counts by the time period to get the rate.
For slow counts, I agree, but for high rates, I don't (see above). There can
be glitches and false events that can (and must) be effectively filtered out.
For that user-space needs to know the time of each event during the
measurement period.
