Removing AUX channels from alert detection is a bit tricky.
According to a note from datasheet page 27:
To remove AUX5 or AUX5 and AUX3 from the alert detection, conversions on
three auxiliary ADC input channels only must be selected in the control register.
We can check the AUX alert configuration and write to control register HB at
probe but it would not last for long since every other device read sets D15:D14
to 0x00 again. Can't think of any reasonable way to ensure only AUX1,3,5 without
keeping ctrl_hb again. However, AUX selection should not bother if we drop AUX
alert removal support for now.
Few other bits and thoughts inline.
On 12/05, Jonathan Cameron wrote:
> From: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
>
> Convert all the device specific info that was previously in platform data
> over to generic firmware query interfaces.
>
> dt-bindings to follow shortly.
>
> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
> ---
> drivers/staging/iio/adc/ad7280a.c | 100 +++++++++++++++++++++++++-----
> drivers/staging/iio/adc/ad7280a.h | 31 ---------
> 2 files changed, 86 insertions(+), 45 deletions(-)
>
> diff --git a/drivers/staging/iio/adc/ad7280a.c b/drivers/staging/iio/adc/ad7280a.c
> index acaae1b33986..0806238debe3 100644
> --- a/drivers/staging/iio/adc/ad7280a.c
> +++ b/drivers/staging/iio/adc/ad7280a.c
> @@ -23,8 +23,6 @@
> #include <linux/iio/events.h>
> #include <linux/iio/iio.h>
>
> -#include "ad7280a.h"
> -
> /* Registers */
>
> #define AD7280A_CELL_VOLTAGE_1_REG 0x0 /* D11 to D0, Read only */
> @@ -81,6 +79,11 @@
> #define AD7280A_AUX_ADC_UNDERVOLTAGE_REG 0x12 /* D7 to D0, Read/write */
>
> #define AD7280A_ALERT_REG 0x13 /* D7 to D0, Read/write */
> +#define AD7280A_ALERT_REMOVE_MSK GENMASK(3, 0)
> +#define AD7280A_ALERT_REMOVE_AUX5 BIT(0)
> +#define AD7280A_ALERT_REMOVE_AUX4_AUX5 BIT(1)
typo, according to datasheet this bit disables AUX5 and AUX3 so it would be
#define AD7280A_ALERT_REMOVE_AUX3_AUX5 BIT(1)
> +#define AD7280A_ALERT_REMOVE_VIN5 BIT(2)
> +#define AD7280A_ALERT_REMOVE_VIN4_VIN5 BIT(3)
> #define AD7280A_ALERT_GEN_STATIC_HIGH BIT(6)
> #define AD7280A_ALERT_RELAY_SIG_CHAIN_DOWN (BIT(7) | BIT(6))
>
> @@ -163,6 +166,8 @@ static unsigned int ad7280a_devaddr(unsigned int addr)
> struct ad7280_state {
> struct spi_device *spi;
> struct iio_chan_spec *channels;
> + unsigned int chain_last_alert_ignore;
> + bool thermistor_term_en;
> int slave_num;
> int scan_cnt;
> int readback_delay_us;
> @@ -932,14 +937,8 @@ static const struct iio_info ad7280_info_no_irq = {
> .write_event_value = &ad7280a_write_thresh,
> };
>
> -static const struct ad7280_platform_data ad7793_default_pdata = {
> - .acquisition_time = AD7280A_ACQ_TIME_400ns,
> - .thermistor_term_en = true,
> -};
> -
> static int ad7280_probe(struct spi_device *spi)
> {
> - const struct ad7280_platform_data *pdata = dev_get_platdata(&spi->dev);
> struct device *dev = &spi->dev;
> struct ad7280_state *st;
> int ret;
> @@ -954,17 +953,90 @@ static int ad7280_probe(struct spi_device *spi)
> st->spi = spi;
> mutex_init(&st->lock);
>
> - if (!pdata)
> - pdata = &ad7793_default_pdata;
> + st->thermistor_term_en =
> + device_property_read_bool(dev, "adi,thermistor-termination");
> +
> + if (device_property_present(dev, "adi,acquistion-time-ns")) {
typo, adi,acquistion-time-ns -> adi,acquisition-time-ns
> + u32 val;
> +
> + ret = device_property_read_u32(dev, "adi,acquisition-time-ns", &val);
> + if (ret)
> + return ret;
> +
> + switch (val) {
> + case 400:
> + st->acquisition_time = AD7280A_CTRL_LB_ACQ_TIME_400ns;
> + break;
> + case 800:
> + st->acquisition_time = AD7280A_CTRL_LB_ACQ_TIME_800ns;
> + break;
> + case 1200:
> + st->acquisition_time = AD7280A_CTRL_LB_ACQ_TIME_1200ns;
> + break;
> + case 1600:
> + st->acquisition_time = AD7280A_CTRL_LB_ACQ_TIME_1600ns;
> + break;
> + default:
> + dev_err(dev, "Firmware provided acquisition time is invalid\n");
> + return -EINVAL;
> + }
> + } else {
> + st->acquisition_time = AD7280A_CTRL_LB_ACQ_TIME_400ns;
> + }
> +
> + /* Alert masks are intended for when particular inputs are not wired up */
> + if (device_property_present(dev, "adi,voltage-alert-last-chan")) {
> + u8 val;
>
> + ret = device_property_read_u8(dev, "adi,voltage-alert-last-chan", &val);
I added some extra configuration to the ad7280a qemu emulation stuff to test
cases where we would have voltage and temperature channels removed from alert
generation. On my setup, these device_property_read_u8 reads gave me zeros all
the time while the u32 reads gave me the expected values.
Not sure if this is something with qemu or even some misconfiguration from my side.
Would be good if someone else could check it out.
> + if (ret)
> + return ret;
> +
> + switch (val) {
> + case 3:
> + st->chain_last_alert_ignore |= AD7280A_ALERT_REMOVE_VIN4_VIN5;
> + break;
> + case 4:
> + st->chain_last_alert_ignore |= AD7280A_ALERT_REMOVE_VIN5;
> + break;
> + case 5:
> + break;
> + default:
> + dev_err(dev,
> + "Firmware provided last voltage alert channel invalid\n");
> + break;
> + }
> + }
> + if (device_property_present(dev, "adi,temp-alert-last-chan")) {
> + u8 val;
> +
> + ret = device_property_read_u8(dev, "adi,temp-alert-last-chan", &val);
> + if (ret)
> + return ret;
> +
> + switch (val) {
> + case 3:
> + st->chain_last_alert_ignore |= AD7280A_ALERT_REMOVE_AUX4_AUX5;
> + break;
> + case 4:
> + st->chain_last_alert_ignore |= AD7280A_ALERT_REMOVE_AUX5;
> + break;
> + case 5:
> + break;
> + default:
> + dev_err(dev,
> + "Firmware provided last temp alert channel invalid\n");
> + break;
> + }
> + }
> crc8_populate_msb(st->crc_tab, POLYNOM);
>
> st->spi->max_speed_hz = AD7280A_MAX_SPI_CLK_HZ;
> st->spi->mode = SPI_MODE_1;
> spi_setup(st->spi);
>
> - st->ctrl_lb = FIELD_PREP(AD7280A_CTRL_LB_ACQ_TIME_MSK, pdata->acquisition_time) |
> - FIELD_PREP(AD7280A_CTRL_LB_THERMISTOR_MSK, pdata->thermistor_term_en);
> + st->ctrl_lb = FIELD_PREP(AD7280A_CTRL_LB_ACQ_TIME_MSK, st->acquisition_time) |
> + FIELD_PREP(AD7280A_CTRL_LB_THERMISTOR_MSK, st->thermistor_term_en);
> st->oversampling_ratio = 0; /* No oversampling */
>
> ret = ad7280_chain_setup(st);
> @@ -975,7 +1047,6 @@ static int ad7280_probe(struct spi_device *spi)
> st->scan_cnt = (st->slave_num + 1) * AD7280A_NUM_CH;
> st->cell_threshhigh = 0xFF;
> st->aux_threshhigh = 0xFF;
> - st->acquisition_time = pdata->acquisition_time;
>
> ret = devm_add_action_or_reset(dev, ad7280_sw_power_down, st);
> if (ret)
> @@ -1002,7 +1073,8 @@ static int ad7280_probe(struct spi_device *spi)
> ret = ad7280_write(st, ad7280a_devaddr(st->slave_num),
> AD7280A_ALERT_REG, 0,
> AD7280A_ALERT_GEN_STATIC_HIGH |
> - (pdata->chain_last_alert_ignore & 0xF));
> + FIELD_PREP(AD7280A_ALERT_REMOVE_MSK,
> + st->chain_last_alert_ignore));
> if (ret)
> return ret;
>
> diff --git a/drivers/staging/iio/adc/ad7280a.h b/drivers/staging/iio/adc/ad7280a.h
> deleted file mode 100644
> index 99297789a46d..000000000000
> --- a/drivers/staging/iio/adc/ad7280a.h
> +++ /dev/null
> @@ -1,31 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0 */
> -/*
> - * AD7280A Lithium Ion Battery Monitoring System
> - *
> - * Copyright 2011 Analog Devices Inc.
> - */
> -
> -#ifndef IIO_ADC_AD7280_H_
> -#define IIO_ADC_AD7280_H_
> -
> -/*
> - * TODO: struct ad7280_platform_data needs to go into include/linux/iio
> - */
> -
> -#define AD7280A_ACQ_TIME_400ns 0
> -#define AD7280A_ACQ_TIME_800ns 1
> -#define AD7280A_ACQ_TIME_1200ns 2
> -#define AD7280A_ACQ_TIME_1600ns 3
> -
> -#define AD7280A_ALERT_REMOVE_VIN5 BIT(2)
> -#define AD7280A_ALERT_REMOVE_VIN4_VIN5 BIT(3)
> -#define AD7280A_ALERT_REMOVE_AUX5 BIT(0)
> -#define AD7280A_ALERT_REMOVE_AUX4_AUX5 BIT(1)
> -
> -struct ad7280_platform_data {
> - unsigned int acquisition_time;
> - unsigned int chain_last_alert_ignore;
> - bool thermistor_term_en;
> -};
> -
> -#endif /* IIO_ADC_AD7280_H_ */
> --
> 2.34.1
>
