On Fri, 3 Dec 2021 01:25:07 +0200
Cosmin Tanislav <demonsingur@xxxxxxxxx> wrote:
> The AD74412R and AD74413R are quad-channel, software configurable,
> input/output solutions for building and process control applications.
>
> They contain functionality for analog output, analog input, digital input,
> resistance temperature detector, and thermocouple measurements integrated
> into a single chip solution with an SPI interface.
>
> The devices feature a 16-bit ADC and four configurable 13-bit DACs to
> provide four configurable input/output channels and a suite of diagnostic
> functions.
>
> The AD74413R differentiates itself from the AD74412R by being
> HART-compatible.
>
> When configured with channel 0 as voltage output, channel 1 as current
> output, channel 2 as voltage input and channel 3 as current input, the
> following structure is created under the corresponding IIO device.
>
> .
> ├── in_current0_offset
> ├── in_current0_raw
> ├── in_current0_sampling_frequency
> ├── in_current0_sampling_frequency_available
> ├── in_current0_scale
> ├── in_voltage1_offset
> ├── in_voltage1_raw
> ├── in_voltage1_sampling_frequency
> ├── in_voltage1_sampling_frequency_available
> ├── in_voltage1_scale
> ├── in_voltage2_offset
> ├── in_voltage2_raw
> ├── in_voltage2_sampling_frequency
> ├── in_voltage2_sampling_frequency_available
> ├── in_voltage2_scale
> ├── in_current3_offset
> ├── in_current3_raw
> ├── in_current3_sampling_frequency
> ├── in_current3_sampling_frequency_available
> ├── in_current3_scale
> ├── out_voltage0_raw
> ├── out_voltage0_scale
> ├── out_current1_raw
> ├── out_current1_scale
> ├── name
> ├── buffer
> │ ├── data_available
> │ ├── enable
> │ ├── length
> │ └── watermark
> └── scan_elements
> ├── in_current0_en
> ├── in_current0_index
> ├── in_current0_type
> ├── in_voltage1_en
> ├── in_voltage1_index
> ├── in_voltage1_type
> ├── in_voltage2_en
> ├── in_voltage2_index
> ├── in_voltage2_type
> ├── in_current3_en
> ├── in_current3_index
> └── in_current3_type
>
> Signed-off-by: Cosmin Tanislav <cosmin.tanislav@xxxxxxxxxx>
You haven't picked up Linus' tag from v7. I'm assuming that wasn't deliberate
so please add it for v10. I think there is just enough stuff in here that it makes
more sense for you to spin a new version than for me to fix it whilst applying...
All minor stuff so shouldn't take long hopefully + we still need a dt review
which might take a while depending on how busy Rob is.
thanks,
Jonathan
> ---
> --- /dev/null
> +++ b/drivers/iio/addac/ad74413r.c
> @@ -0,0 +1,1476 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2021 Analog Devices, Inc.
> + * Author: Cosmin Tanislav <cosmin.tanislav@xxxxxxxxxx>
> + */
> +
...
> +struct ad74413r_state {
> + struct ad74413r_channel_config channel_configs[AD74413R_CHANNEL_MAX];
> + unsigned int gpo_gpio_offsets[AD74413R_CHANNEL_MAX];
> + unsigned int comp_gpio_offsets[AD74413R_CHANNEL_MAX];
> + struct gpio_chip gpo_gpiochip;
> + struct gpio_chip comp_gpiochip;
> + struct completion adc_data_completion;
> + unsigned int num_gpo_gpios;
> + unsigned int num_comparator_gpios;
> + u32 sense_resistor_ohms;
> +
> + /*
> + * Synchronize consecutive operations when doing a one-shot
> + * conversion and when updating the ADC samples SPI message.
> + */
> + struct mutex lock;
> +
> + const struct ad74413r_chip_info *chip_info;
> + struct spi_device *spi;
> + struct regulator *refin_reg;
> + struct regmap *regmap;
> + struct device *dev;
> + struct iio_trigger *trig;
> +
> + size_t adc_active_channels;
> + struct spi_message adc_samples_msg;
> + struct spi_transfer adc_samples_xfer[AD74413R_CHANNEL_MAX + 1];
> +
> + /*
> + * DMA (thus cache coherency maintenance) requires the
> + * transfer buffers to live in their own cache lines.
> + */
> + struct {
> + u8 rx_buf[AD74413R_FRAME_SIZE * AD74413R_CHANNEL_MAX];
> + s64 timestamp;
> + } adc_samples_buf ____cacheline_aligned;
> +
> + u8 adc_samples_tx_buf[AD74413R_FRAME_SIZE * AD74413R_CHANNEL_MAX]
> + ____cacheline_aligned;
What was your thinking for needing to have both adc_samples_buf and adc_samples_tx_buf
at force alignment? I would have expected only adc_samples_buf would be necessary,
unless there are paths in which you are writing into one whilst DMA is going on into
the other.. If there is a reason add a comment.
> + u8 reg_tx_buf[AD74413R_FRAME_SIZE];
> + u8 reg_rx_buf[AD74413R_FRAME_SIZE];
> +};
> +
> +
> +static int ad74413r_probe(struct spi_device *spi)
> +{
> + struct ad74413r_state *st;
> + struct iio_dev *indio_dev;
> + int ret;
> +
> + indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + st = iio_priv(indio_dev);
> +
> + st->spi = spi;
> + st->dev = &spi->dev;
> + st->chip_info = device_get_match_data(&spi->dev);
> + mutex_init(&st->lock);
> + init_completion(&st->adc_data_completion);
> +
> + st->regmap = devm_regmap_init(st->dev, NULL, st,
> + &ad74413r_regmap_config);
> + if (IS_ERR(st->regmap))
> + return PTR_ERR(st->regmap);
> +
> + st->refin_reg = devm_regulator_get(st->dev, "refin");
> + if (IS_ERR(st->refin_reg))
> + return dev_err_probe(st->dev, PTR_ERR(st->refin_reg),
> + "Failed to get refin regulator\n");
> +
> + ret = regulator_enable(st->refin_reg);
> + if (ret)
> + return ret;
> +
> + ret = devm_add_action_or_reset(st->dev, ad74413r_regulator_disable,
> + st->refin_reg);
> + if (ret)
> + return ret;
> +
> + st->sense_resistor_ohms = 100000000;
> + device_property_read_u32(st->dev, "shunt-resistor-micro-ohms",
> + &st->sense_resistor_ohms);
> + st->sense_resistor_ohms /= 1000000;
> +
> + st->trig = devm_iio_trigger_alloc(st->dev, "%s-dev%d",
> + st->chip_info->name, iio_device_id(indio_dev));
> + if (!st->trig)
> + return -ENOMEM;
> +
> + st->trig->ops = &ad74413r_trigger_ops;
> + iio_trigger_set_drvdata(st->trig, st);
> +
> + ret = devm_iio_trigger_register(st->dev, st->trig);
> + if (ret)
> + return ret;
> +
> + indio_dev->name = st->chip_info->name;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->info = &ad74413r_info;
> + indio_dev->trig = iio_trigger_get(st->trig);
> +
> + ret = ad74413r_reset(st);
> + if (ret)
> + return ret;
> +
> + ret = ad74413r_parse_channel_configs(indio_dev);
> + if (ret)
> + return ret;
> +
> + ret = ad74413r_setup_channels(indio_dev);
> + if (ret)
> + return ret;
> +
> + ret = ad74413r_setup_gpios(st);
> + if (ret)
> + return ret;
> +
> + if (st->num_gpo_gpios) {
> + st->gpo_gpiochip.owner = THIS_MODULE;
> + st->gpo_gpiochip.label = st->chip_info->name;
> + st->gpo_gpiochip.base = -1;
> + st->gpo_gpiochip.ngpio = st->num_gpo_gpios;
> + st->gpo_gpiochip.parent = st->dev;
> + st->gpo_gpiochip.can_sleep = true;
> + st->gpo_gpiochip.set = ad74413r_gpio_set;
> + st->gpo_gpiochip.set_multiple = ad74413r_gpio_set_multiple;
> + st->gpo_gpiochip.set_config = ad74413r_gpio_set_gpo_config;
> + st->gpo_gpiochip.get_direction =
> + ad74413r_gpio_get_gpo_direction;
> +
> + ret = devm_gpiochip_add_data(st->dev, &st->gpo_gpiochip, st);
> + if (ret)
> + return ret;
> + }
> +
> + if (st->num_comparator_gpios) {
> + st->comp_gpiochip.owner = THIS_MODULE;
> + st->comp_gpiochip.label = st->chip_info->name;
> + st->comp_gpiochip.base = -1;
> + st->comp_gpiochip.ngpio = st->num_comparator_gpios;
> + st->comp_gpiochip.parent = st->dev;
> + st->comp_gpiochip.can_sleep = true;
> + st->comp_gpiochip.get = ad74413r_gpio_get;
> + st->comp_gpiochip.get_multiple = ad74413r_gpio_get_multiple;
> + st->comp_gpiochip.set_config = ad74413r_gpio_set_comp_config;
> + st->comp_gpiochip.get_direction =
> + ad74413r_gpio_get_comp_direction;
> +
> + ret = devm_gpiochip_add_data(st->dev, &st->comp_gpiochip, st);
> + if (ret)
> + return ret;
> + }
> +
> + ret = ad74413r_set_adc_conv_seq(st, AD74413R_CONV_SEQ_OFF);
> + if (ret)
> + return ret;
> +
> + ret = devm_request_irq(st->dev, spi->irq, ad74413r_adc_data_interrupt,
> + 0, st->chip_info->name, indio_dev);
> + if (ret)
Minor, but would be good to have a dev_err_probe() here as
this is something that can result in a deferred response and it would
be good to log the debugging info.
> + return ret;
> +
> + ret = devm_iio_triggered_buffer_setup(st->dev, indio_dev,
> + &iio_pollfunc_store_time,
> + &ad74413r_trigger_handler,
> + &ad74413r_buffer_ops);
> + if (ret)
> + return ret;
> +
> + return devm_iio_device_register(st->dev, indio_dev);
> +}
