On Fri, 6 Aug 2021 21:33:44 -0300 Lucas Stankus <lucas.p.stankus@xxxxxxxxx> wrote: > On Fri, Aug 6, 2021 at 3:10 PM Rob Herring <robh@xxxxxxxxxx> wrote: > > > > On Thu, Aug 05, 2021 at 03:29:37AM -0300, Lucas Stankus wrote: > > > Add device tree binding documentation for ADXL313 3-axis accelerometer. > > > > > > Signed-off-by: Lucas Stankus <lucas.p.stankus@xxxxxxxxx> > > > --- > > > .../bindings/iio/accel/adi,adxl313.yaml | 90 +++++++++++++++++++ > > > 1 file changed, 90 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml > > > > > > diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml > > > new file mode 100644 > > > index 000000000000..fea03b6790f3 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml > > > @@ -0,0 +1,90 @@ > > > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/iio/accel/adi,adxl313.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: Analog Devices ADXL313 3-Axis Digital Accelerometer > > > + > > > +maintainers: > > > + - Lucas Stankus <lucas.p.stankus@xxxxxxxxx> > > > + > > > +description: | > > > + Analog Devices ADXL313 3-Axis Digital Accelerometer that supports > > > + both I2C & SPI interfaces. > > > + https://www.analog.com/en/products/adxl313.html > > > + > > > +properties: > > > + compatible: > > > + enum: > > > + - adi,adxl313 > > > + > > > + reg: > > > + maxItems: 1 > > > + > > > + spi-3wire: true > > > + > > > + spi-cpha: true > > > + > > > + spi-cpol: true > > > > These 3 generally shouldn't be needed, but can be set from the driver. > > If they are valid, is any combination of them really valid? > > > > Only the 3wire is optional, both cpha and cpol are required for proper > spi connection. We've been round this one a few time, and last time we discussed the cases where you'd need these in DT (because of inverters on the bus) https://lore.kernel.org/linux-iio/20191204111231.GO1998@xxxxxxxxxxxxx/ conclusion was, that we don't want to put the burden on the dt files for those odd cases. The equivalent for interrupt lines is interestingly different because in those cases the two-cell version includes the type of interrupt, so it makes little sense to push that down into the drivers as well. Mind you I'm not 100% sure how we would retrofit a binding if necessary for the inverted cases. Hope we don't hit one here :) As you note, 3wire is needed in the binding because it's optional. Jonathan > > > > + > > > + spi-max-frequency: true > > > + > > > + vs-supply: > > > + description: Regulator that supplies power to the accelerometer > > > + > > > + vdd-supply: > > > + description: Regulator that supplies the digital interface supply voltage > > > + > > > + interrupts: > > > + maxItems: 2 > > > > This means there must be 2 entries. If 1 is valid, you need 'minItems'. > > > > I'll add 'minItems' for the v3 then, thanks! > > > > + > > > + interrupt-names: > > > + maxItems: 2 > > > > You need 'minItems' too to fix the error. > > > > Thank you again and sorry for not catching that error before submitting. > > > > + items: > > > + enum: > > > + - INT1 > > > + - INT2 > > > + > > > +required: > > > + - compatible > > > + - reg > > > + > > > +additionalProperties: false > > > + > > > +examples: > > > + - | > > > + #include <dt-bindings/gpio/gpio.h> > > > + #include <dt-bindings/interrupt-controller/irq.h> > > > + i2c0 { > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + > > > + /* Example for a I2C device node */ > > > + accelerometer@53 { > > > + compatible = "adi,adxl313"; > > > + reg = <0x53>; > > > + interrupt-parent = <&gpio0>; > > > + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; > > > + interrupt-names = "INT1"; > > > + }; > > > + }; > > > + - | > > > + #include <dt-bindings/gpio/gpio.h> > > > + #include <dt-bindings/interrupt-controller/irq.h> > > > + spi { > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + > > > + /* Example for a SPI device node */ > > > + accelerometer@0 { > > > + compatible = "adi,adxl313"; > > > + reg = <0>; > > > + spi-max-frequency = <5000000>; > > > + spi-cpol; > > > + spi-cpha; > > > + interrupt-parent = <&gpio0>; > > > + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; > > > + interrupt-names = "INT1"; > > > + }; > > > + }; > > > -- > > > 2.32.0 > > > > > >
