Hi Jonathan,
Thank you for the review.
On Sat, Jul 24, 2021 at 7:03 PM Jonathan Cameron <jic23@xxxxxxxxxx> wrote:
>
> On Mon, 19 Jul 2021 09:58:38 +0100
> Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> wrote:
>
> > Add ADC driver support for Renesas RZ/G2L A/D converter in SW
> > trigger mode.
> >
> > A/D Converter block is a successive approximation analog-to-digital
> > converter with a 12-bit accuracy and supports a maximum of 8 input
> > channels.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > Reviewed-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
>
> Hi Lad,
>
> A few additional comments inline.
>
> Thanks,
>
> Jonathan
>
> > ---
> > MAINTAINERS | 8 +
> > drivers/iio/adc/Kconfig | 10 +
> > drivers/iio/adc/Makefile | 1 +
> > drivers/iio/adc/rzg2l_adc.c | 545 ++++++++++++++++++++++++++++++++++++
> > 4 files changed, 564 insertions(+)
> > create mode 100644 drivers/iio/adc/rzg2l_adc.c
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 6c8be735cc91..6a52f9f4604c 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -15839,6 +15839,14 @@ L: linux-renesas-soc@xxxxxxxxxxxxxxx
> > S: Maintained
> > F: drivers/phy/renesas/phy-rcar-gen3-usb*.c
> >
> > +RENESAS RZ/G2L A/D DRIVER
> > +M: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > +L: linux-iio@xxxxxxxxxxxxxxx
> > +L: linux-renesas-soc@xxxxxxxxxxxxxxx
> > +S: Supported
> > +F: Documentation/devicetree/bindings/iio/adc/renesas,rzg2l-adc.yaml
> > +F: drivers/iio/adc/rzg2l_adc.c
> > +
> > RESET CONTROLLER FRAMEWORK
> > M: Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>
> > S: Maintained
> > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> > index db0c8fb60515..af168e1c9fdb 100644
> > --- a/drivers/iio/adc/Kconfig
> > +++ b/drivers/iio/adc/Kconfig
> > @@ -887,6 +887,16 @@ config ROCKCHIP_SARADC
> > To compile this driver as a module, choose M here: the
> > module will be called rockchip_saradc.
> >
> > +config RZG2L_ADC
> > + tristate "Renesas RZ/G2L ADC driver"
> > + depends on ARCH_R9A07G044 || COMPILE_TEST
> > + help
> > + Say yes here to build support for the ADC found in Renesas
> > + RZ/G2L family.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called rzg2l_adc.
> > +
> > config SC27XX_ADC
> > tristate "Spreadtrum SC27xx series PMICs ADC"
> > depends on MFD_SC27XX_PMIC || COMPILE_TEST
> > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> > index f70d877c555a..d68550f493e3 100644
> > --- a/drivers/iio/adc/Makefile
> > +++ b/drivers/iio/adc/Makefile
> > @@ -82,6 +82,7 @@ obj-$(CONFIG_QCOM_PM8XXX_XOADC) += qcom-pm8xxx-xoadc.o
> > obj-$(CONFIG_RCAR_GYRO_ADC) += rcar-gyroadc.o
> > obj-$(CONFIG_RN5T618_ADC) += rn5t618-adc.o
> > obj-$(CONFIG_ROCKCHIP_SARADC) += rockchip_saradc.o
> > +obj-$(CONFIG_RZG2L_ADC) += rzg2l_adc.o
> > obj-$(CONFIG_SC27XX_ADC) += sc27xx_adc.o
> > obj-$(CONFIG_SPEAR_ADC) += spear_adc.o
> > obj-$(CONFIG_STX104) += stx104.o
> > diff --git a/drivers/iio/adc/rzg2l_adc.c b/drivers/iio/adc/rzg2l_adc.c
> > new file mode 100644
> > index 000000000000..033cdec9e976
> > --- /dev/null
> > +++ b/drivers/iio/adc/rzg2l_adc.c
> > @@ -0,0 +1,545 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * RZ/G2L A/D Converter driver
> > + *
> > + * Copyright (c) 2021 Renesas Electronics Europe GmbH
> > + *
> > + * Author: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/completion.h>
> > +#include <linux/delay.h>
> > +#include <linux/iio/iio.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/io.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
>
> Add mod_devicetable.h and drop the of specific headers
> as nothing in them used directly as far as I can tell.
>
OK.
> > +#include <linux/platform_device.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/reset.h>
> > +
> > +#define DRIVER_NAME "rzg2l-adc"
> > +
> > +#define RZG2L_ADM(n) ((n) * 0x4)
> > +#define RZG2L_ADM0_ADCE BIT(0)
> > +#define RZG2L_ADM0_ADBSY BIT(1)
> > +#define RZG2L_ADM0_PWDWNB BIT(2)
> > +#define RZG2L_ADM0_SRESB BIT(15)
> > +#define RZG2L_ADM1_TRG BIT(0)
> > +#define RZG2L_ADM1_MS BIT(2)
> > +#define RZG2L_ADM1_BS BIT(4)
> > +#define RZG2L_ADM1_EGA_CLEAR ~GENMASK(13, 12)
> > +#define RZG2L_ADM2_CHSEL_CLEAR ~GENMASK(7, 0)
>
> I'd rather see these defined as _MASK and the
> inversion made explicit inline.
>
OK will use them as _MASK's and invert inline when required.
> > +#define RZG2L_ADM3_ADSMP 0x578
> > +#define RZG2L_ADM3_ADCMP (0xe << 16)
> > +#define RZG2L_ADM3_ADIL_CLEAR ~GENMASK(31, 24)
> > +
> > +#define RZG2L_ADINT 0x20
> > +#define RZG2L_ADINT_CH_CLEAR ~GENMASK(7, 0)
> > +#define RZG2L_ADINT_CSEEN BIT(16)
> > +#define RZG2L_ADINT_INTS BIT(31)
> > +#define RZG2L_ADSTS 0x24
> > +#define RZG2L_ADINT_INTST_MASK GENMASK(7, 0)
> > +#define RZG2L_ADSTS_CSEST BIT(16)
> > +#define RZG2L_ADIVC 0x28
> > +#define RZG2L_ADIVC_DIVADC_CLEAR ~GENMASK(8, 0)
> > +#define RZG2L_ADIVC_DIVADC_4 0x4
>
> Perhaps adopt the _MASK and FIELD_PREP() approach to setting
> particular values. That way it is obvious at the call site that
> DVADC_4 is a value within the DIVADC_MASK covered field.
>
Agreed will change that.
> > +#define RZG2L_ADFIL 0x2c
> > +#define RZG2L_ADCR(n) (0x30 + ((n) * 0x4))
> > +#define RZG2L_ADCR_AD_MASK GENMASK(11, 0)
> > +
> > +#define RZG2L_ADC_MAX_CHANNELS 8
> > +#define RZG2L_ADC_CHN_MASK 0x7
> > +#define RZG2L_ADC_TIMEOUT usecs_to_jiffies(1 * 4)
> > +
> > +struct rzg2l_adc_data {
> > + const struct iio_chan_spec *channels;
> > + u8 num_channels;
> > +};
> > +
> > +struct rzg2l_adc {
> > + void __iomem *base;
> > + struct clk *pclk;
> > + struct clk *adclk;
> > + struct reset_control *presetn;
> > + struct reset_control *adrstn;
> > + struct completion completion;
> > + const struct rzg2l_adc_data *data;
> > + u16 last_val[RZG2L_ADC_MAX_CHANNELS];
> > +};
> > +
> > +static const char * const rzg2l_adc_channel_name[] = {
> > + "adc0",
> Is it useful to expose these as labels to userspace?
> Seems unnecessary given they map directly to the channel
> numbers.
>
Exposing them as this may vary depending on the wiring on the board,
so it would be better for user space to know which channels are
available.
> > + "adc1",
> > + "adc2",
> > + "adc3",
> > + "adc4",
> > + "adc5",
> > + "adc6",
> > + "adc7",
> > +};
> > +
> > +static unsigned int rzg2l_adc_readl(struct rzg2l_adc *adc, u32 reg)
> > +{
> > + return readl(adc->base + reg);
> > +}
> > +
> > +static void rzg2l_adc_writel(struct rzg2l_adc *adc, unsigned int reg, u32 val)
> > +{
> > + writel(val, adc->base + reg);
> > +}
> > +
> > +static void rzg2l_adc_pwr(struct rzg2l_adc *adc, bool on)
> > +{
> > + u32 reg;
> > +
> > + reg = rzg2l_adc_readl(adc, RZG2L_ADM(0));
> > + if (on)
> > + reg |= RZG2L_ADM0_PWDWNB;
> > + else
> > + reg &= ~RZG2L_ADM0_PWDWNB;
> > + rzg2l_adc_writel(adc, RZG2L_ADM(0), reg);
> > + udelay(2);
> > +}
> > +
> > +static void rzg2l_adc_start_stop(struct rzg2l_adc *adc, bool start)
> > +{
> > + int timeout = 5;
> > + u32 reg;
> > +
> > + /* stop A/D conversion */
> > + reg = rzg2l_adc_readl(adc, RZG2L_ADM(0));
> > + if (start)
> > + reg |= RZG2L_ADM0_ADCE;
> > + else
> > + reg &= ~RZG2L_ADM0_ADCE;
> > + rzg2l_adc_writel(adc, RZG2L_ADM(0), reg);
> > +
> > + if (start)
> > + return;
> > +
> > + do {
> > + usleep_range(100, 200);
> > + reg = rzg2l_adc_readl(adc, RZG2L_ADM(0));
> > + timeout--;
> > + if (!timeout) {
> > + pr_err("%s stopping ADC timed out\n", __func__);
> > + break;
> > + }
> > + } while (((reg & RZG2L_ADM0_ADBSY) || (reg & RZG2L_ADM0_ADCE)));
> > +}
> > +
> > +static void rzg2l_set_trigger(struct rzg2l_adc *adc)
> > +{
> > + u32 reg;
> > +
> > + /* SW trigger */
> > + reg = rzg2l_adc_readl(adc, RZG2L_ADM(1));
> > + reg &= RZG2L_ADM1_EGA_CLEAR;
> > + reg &= ~RZG2L_ADM1_BS;
> > + reg |= RZG2L_ADM1_MS;
> > + reg &= ~RZG2L_ADM1_TRG;
> > + rzg2l_adc_writel(adc, RZG2L_ADM(1), reg);
> > +}
> > +
> > +static int rzg2l_adc_conversion_setup(struct rzg2l_adc *adc, u8 ch)
> > +{
> > + u32 reg;
> > +
> > + if (rzg2l_adc_readl(adc, RZG2L_ADM(0)) & RZG2L_ADM0_ADBSY)
> > + return -EBUSY;
> > +
> > + rzg2l_set_trigger(adc);
> > +
> > + /* select channel */
> > + reg = rzg2l_adc_readl(adc, RZG2L_ADM(2));
> > + reg &= RZG2L_ADM2_CHSEL_CLEAR;
> > + reg |= BIT(ch);
> > + rzg2l_adc_writel(adc, RZG2L_ADM(2), reg);
> > +
> > + reg = rzg2l_adc_readl(adc, RZG2L_ADM(3));
> > + reg &= RZG2L_ADM3_ADIL_CLEAR;
> > + reg |= RZG2L_ADM3_ADCMP;
> > + reg |= RZG2L_ADM3_ADSMP;
>
> No loss in readability in combining the two lines above and shorter
> code is always good. Having the mask on a separate line makes
> sense but the |= pair doesn't.
>
Agreed will move to the same line.
> What is a bit unusual here is you clear some bits then write different
> ones. That is presumably relying on the fact that the ADCCMP part
> is always set to the same value. That seems unwise to assume from
> a long term maintainability point of view.
>
The ADIL bits have to be set to zero, so I am clearing the ADIL bits
(bit 24-bits 31) and the ADCMP/ADSMP should be set to specific values
oxe/0x578 respectively.
> > + rzg2l_adc_writel(adc, RZG2L_ADM(3), reg);
> > +
> > + reg = rzg2l_adc_readl(adc, RZG2L_ADIVC);
> > + reg &= RZG2L_ADIVC_DIVADC_CLEAR;
> > + reg |= RZG2L_ADIVC_DIVADC_4;
> > + rzg2l_adc_writel(adc, RZG2L_ADIVC, reg);
> > +
> > + reg = rzg2l_adc_readl(adc, RZG2L_ADINT);
> > + reg &= ~RZG2L_ADINT_INTS;
> > + reg &= RZG2L_ADINT_CH_CLEAR;
> > + reg |= RZG2L_ADINT_CSEEN;
> > + reg |= BIT(ch);
> > + rzg2l_adc_writel(adc, RZG2L_ADINT, reg);
> > +
> > + return 0;
> > +}
> > +
> > +static int rzg2l_adc_set_power(struct iio_dev *indio_dev, bool on)
> > +{
> > + struct device *dev = indio_dev->dev.parent;
> > +
> > + if (on)
> > + return pm_runtime_resume_and_get(dev);
> > +
> > + return pm_runtime_put_sync(dev);
> > +}
> > +
> > +static int rzg2l_adc_conversion(struct iio_dev *indio_dev, struct rzg2l_adc *adc, u8 ch)
> > +{
> > + int ret;
> > +
> > + ret = rzg2l_adc_set_power(indio_dev, true);
> > + if (ret)
> > + return ret;
> > +
> > + ret = rzg2l_adc_conversion_setup(adc, ch);
> > + if (ret) {
> > + rzg2l_adc_set_power(indio_dev, false);
> > + return ret;
> > + }
> > +
> > + reinit_completion(&adc->completion);
> > +
> > + rzg2l_adc_start_stop(adc, true);
> > +
> > + if (!wait_for_completion_timeout(&adc->completion, RZG2L_ADC_TIMEOUT)) {
> > + rzg2l_adc_writel(adc, RZG2L_ADINT,
> > + rzg2l_adc_readl(adc, RZG2L_ADINT) & RZG2L_ADINT_CH_CLEAR);
> > + rzg2l_adc_start_stop(adc, false);
> > + rzg2l_adc_set_power(indio_dev, false);
> > + return -ETIMEDOUT;
> > + }
> > +
> > + return rzg2l_adc_set_power(indio_dev, false);
> > +}
> > +
> > +static int rzg2l_adc_read_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan,
> > + int *val, int *val2, long mask)
> > +{
> > + struct rzg2l_adc *adc = iio_priv(indio_dev);
> > + int ret;
> > + u8 ch;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_RAW:
> > + if (chan->type != IIO_VOLTAGE)
> > + return -EINVAL;
> > +
> > + ret = iio_device_claim_direct_mode(indio_dev);
> > + if (ret)
> > + return ret;
> > +
> > + ch = chan->channel & RZG2L_ADC_CHN_MASK;
> > + ret = rzg2l_adc_conversion(indio_dev, adc, ch);
> > + if (ret) {
> > + iio_device_release_direct_mode(indio_dev);
> > + return ret;
> > + }
> > + *val = adc->last_val[ch];
> > + iio_device_release_direct_mode(indio_dev);
> > +
> > + return IIO_VAL_INT;
> > +
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static int rzg2l_adc_read_label(struct iio_dev *iio_dev,
> > + const struct iio_chan_spec *chan,
> > + char *label)
> > +{
> > + if (chan->channel >= RZG2L_ADC_MAX_CHANNELS)
> > + return -EINVAL;
> > +
> > + return snprintf(label, PAGE_SIZE, "%s\n", rzg2l_adc_channel_name[chan->channel]);
>
> sysfs_emit()?.
>
OK
> > +}
> > +
> > +static const struct iio_info rzg2l_adc_iio_info = {
> > + .read_raw = rzg2l_adc_read_raw,
> > + .read_label = rzg2l_adc_read_label,
> > +};
> > +
> > +static irqreturn_t rzg2l_adc_isr(int irq, void *dev_id)
> > +{
> > + struct rzg2l_adc *adc = (struct rzg2l_adc *)dev_id;
> > + u8 intst;
> > + u32 reg;
> > + u8 i;
> > +
> > + reg = rzg2l_adc_readl(adc, RZG2L_ADSTS);
> > + if (reg & RZG2L_ADSTS_CSEST) {
>
> Probably good to add a brief comment on what is going on in this check.
> Perhaps even an error print if it's an error path.
>
Agreed will add a comment, this condition happens on channel selection error.
> > + rzg2l_adc_writel(adc, RZG2L_ADSTS, reg);
> > + return IRQ_HANDLED;
> > + }
> > +
> > + intst = reg & RZG2L_ADINT_INTST_MASK;
> > + if (!intst)
>
> I'm guessing this means spurious interrupt in which case IRQ_NONE
> so the core irq code knows about it.
>
Agreed IRQ_NONE should be returned.
> > + return IRQ_HANDLED;
> > +
> > + for (i = 0; i < RZG2L_ADC_MAX_CHANNELS; i++) {
> > + if (intst & BIT(i))
>
> for_each_bit_set() and make intst a long so the types are right for
> that macro
>
>
Agreed will do.
> > + adc->last_val[i] = rzg2l_adc_readl(adc, RZG2L_ADCR(i)) & RZG2L_ADCR_AD_MASK;
> > + }
> > +
> > + rzg2l_adc_writel(adc, RZG2L_ADSTS, reg);
> > +
> > + complete(&adc->completion);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int rzg2l_adc_parse_of(struct platform_device *pdev, struct rzg2l_adc *adc)
> > +{
> > + struct iio_chan_spec *chan_array;
> > + struct fwnode_handle *fwnode;
> > + struct rzg2l_adc_data *data;
> > + unsigned int channel;
> > + int num_channels;
> > + int ret;
> > + u8 i;
> > +
> > + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> > + if (!data)
> > + return -ENOMEM;
> > +
> > + num_channels = device_get_child_node_count(&pdev->dev);
> > + if (!num_channels) {
> > + dev_err(&pdev->dev, "no channel children\n");
> > + return -ENODEV;
> > + }
> > +
> > + if (num_channels > RZG2L_ADC_MAX_CHANNELS) {
> > + dev_err(&pdev->dev, "num of channel children out of range\n");
> > + return -EINVAL;
> > + }
> > +
> > + chan_array = devm_kcalloc(&pdev->dev, num_channels, sizeof(*chan_array),
> > + GFP_KERNEL);
> > + if (!chan_array)
> > + return -ENOMEM;
> > +
> > + i = 0;
> > + device_for_each_child_node(&pdev->dev, fwnode) {
> > + ret = fwnode_property_read_u32(fwnode, "reg", &channel);
> > + if (ret)
> > + return ret;
> > +
> > + if (channel >= RZG2L_ADC_MAX_CHANNELS)
> > + return -EINVAL;
> > +
> > + chan_array[i].type = IIO_VOLTAGE;
> > + chan_array[i].indexed = 1;
> > + chan_array[i].channel = channel;
> > + chan_array[i].info_mask_separate = BIT(IIO_CHAN_INFO_RAW);
> > + chan_array[i].datasheet_name = rzg2l_adc_channel_name[channel];
> > + i++;
> > + }
> > +
> > + data->num_channels = num_channels;
> > + data->channels = chan_array;
> > + adc->data = data;
> > +
> > + return 0;
> > +}
> > +
> > +static int rzg2l_adc_sw_reset(struct rzg2l_adc *adc)
> > +{
> > + int timeout = 5;
> > + u32 val;
> > +
> > + val = rzg2l_adc_readl(adc, RZG2L_ADM(0));
> > + val |= RZG2L_ADM0_SRESB;
> > + rzg2l_adc_writel(adc, RZG2L_ADM(0), val);
> > +
> > + while (!(rzg2l_adc_readl(adc, RZG2L_ADM(0)) & RZG2L_ADM0_SRESB)) {
> > + if (!timeout)
> > + return -EBUSY;
> > + timeout--;
> > + usleep_range(100, 200);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int rzg2l_adc_probe(struct platform_device *pdev)
> > +{
> > + struct device *dev = &pdev->dev;
> > + struct iio_dev *indio_dev;
> > + struct rzg2l_adc *adc;
> > + int ret;
> > + int irq;
> > +
> > + indio_dev = devm_iio_device_alloc(dev, sizeof(*adc)
> > + if (!indio_dev)
> > + return -ENOMEM;
> > +
> > + adc = iio_priv(indio_dev);
> > +
> > + ret = rzg2l_adc_parse_of(pdev, adc);
>
> *_parse_properties() or *_parse_firmware()
> as it's not of specific now.
>
OK will rename it to rzg2l_adc_parse_properties().
> > + if (ret)
> > + return ret;
> > +
> > + adc->base = devm_platform_ioremap_resource(pdev, 0);
> > + if (IS_ERR(adc->base))
> > + return PTR_ERR(adc->base);
> > +
> > + irq = platform_get_irq(pdev, 0);
> > + if (irq < 0) {
> > + dev_err(dev, "no irq resource\n");
> > + return irq;
> > + }
> > +
> > + adc->pclk = devm_clk_get(dev, "pclk");
> > + if (IS_ERR(adc->pclk)) {
> > + dev_err(dev, "Failed to get pclk");
> > + return PTR_ERR(adc->pclk);
> > + }
> > +
> > + adc->adclk = devm_clk_get(dev, "adclk");
> > + if (IS_ERR(adc->adclk)) {
> > + dev_err(dev, "Failed to get adclk");
> > + return PTR_ERR(adc->adclk);
> > + }
> > +
> > + adc->adrstn = devm_reset_control_get_exclusive(dev, "adrst-n");
> > + if (IS_ERR(adc->adrstn)) {
> > + dev_err(dev, "failed to get adrstn\n");
> > + return PTR_ERR(adc->adrstn);
> > + }
> > +
> > + adc->presetn = devm_reset_control_get_exclusive(dev, "presetn");
> > + if (IS_ERR(adc->presetn)) {
> > + dev_err(dev, "failed to get presetn\n");
> > + return PTR_ERR(adc->presetn);
> > + }
> > +
> > + ret = reset_control_deassert(adc->adrstn);
> > + if (ret)
> > + return ret;
>
> devm_add_action_or_reset() here to make the reasserting of these part
> of the automated cleanup.
>
OK will use devm_add_action_or_reset().
> > +
> > + ret = reset_control_deassert(adc->presetn);
> > + if (ret)
> > + goto assert_adrstn;
> > +
> > + ret = clk_prepare_enable(adc->pclk);
> > + if (ret)
> > + goto assert_presetn;
> > +
> > + ret = rzg2l_adc_sw_reset(adc);
> > + if (ret)
> > + goto unprepare_pclk;
> > +
> > + clk_disable_unprepare(adc->pclk);
>
> As below, reorder as:
>
> ret = rzg2l_adc_sw_reset(adc);
> clk_disable_unprepare(adc->pclk);
> if (ret)
> goto assert_preset_n;
>
Agreed.
> > +
> > + init_completion(&adc->completion);
> > +
> > + platform_set_drvdata(pdev, indio_dev);
> > +
> > + ret = devm_request_irq(dev, irq, rzg2l_adc_isr,
> > + 0, dev_name(dev), adc);
>
> Another aspect of the comment below about mixing and matching between
> devm and not. If the order of remove is not that opposite of probe
> then there should be a comment saying why. There are far too many
> race conditions introduced by people doing things in a different order
> without carefully considering why.
>
Agreed will completely move to devm
> > + if (ret < 0)
> > + goto assert_presetn;
> > +
> > + indio_dev->name = DRIVER_NAME;
> > + indio_dev->info = &rzg2l_adc_iio_info;
> > + indio_dev->modes = INDIO_DIRECT_MODE;
> > + indio_dev->channels = adc->data->channels;
> > + indio_dev->num_channels = adc->data->num_channels;
> > +
> > + pm_runtime_enable(dev);
> > +
> > + ret = devm_iio_device_register(dev, indio_dev);
> > + if (ret)
> > + goto err_iio_device_register;
> > +
> > + return 0;
> > +
> > +unprepare_pclk:
> > + clk_disable_unprepare(adc->pclk);
>
> Bad sign that you have this here and not in remove..
> When you have cases like this, it's normally better to
> either factor out the relevant code into a function
> that lets you do this call whether or not there is an
> error, or to just move this up to the relevant if statements.
>
As agreed above, will alter the code.
>
> > +err_iio_device_register:
> > + pm_runtime_disable(dev);
> > +assert_presetn:
> > + reset_control_assert(adc->presetn);
> > +assert_adrstn:
> > + reset_control_assert(adc->adrstn);
> > + return ret;
> > +}
> > +
> > +static int rzg2l_adc_remove(struct platform_device *pdev)
> > +{
> > + struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> > + struct rzg2l_adc *adc = iio_priv(indio_dev);
> > +
> > + reset_control_assert(adc->presetn);
> > + reset_control_assert(adc->adrstn);
> > + pm_runtime_disable(indio_dev->dev.parent);
>
> You can't mix and match devm managed and unmanaged like this.
> The userspace interfce is still exposed after you've put the
> device into reset which is unlikely to be a good idea.
>
> One option is to use devm_add_action_or_reset() to make
> this stuff happen in the managed flow, which happens after
> remove is done. That would let you drop remove() entirely.
>
Agreed will use devm_add_action_or_reset() and get rid of remove callback().
Cheers,
Prabhakar
>
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id rzg2l_adc_match[] = {
> > + { .compatible = "renesas,rzg2l-adc",},
> > + { /* sentinel */ }
> > +};
> > +MODULE_DEVICE_TABLE(of, rzg2l_adc_match);
> > +
> > +static int __maybe_unused rzg2l_adc_pm_runtime_suspend(struct device *dev)
> > +{
> > + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> > + struct rzg2l_adc *adc = iio_priv(indio_dev);
> > +
> > + rzg2l_adc_pwr(adc, false);
> > + clk_disable_unprepare(adc->adclk);
> > + clk_disable_unprepare(adc->pclk);
> > +
> > + return 0;
> > +}
> > +
> > +static int __maybe_unused rzg2l_adc_pm_runtime_resume(struct device *dev)
> > +{
> > + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> > + struct rzg2l_adc *adc = iio_priv(indio_dev);
> > + int ret;
> > +
> > + ret = clk_prepare_enable(adc->pclk);
> > + if (ret)
> > + return ret;
> > +
> > + ret = clk_prepare_enable(adc->adclk);
> > + if (ret)
> > + return ret;
> > +
> > + rzg2l_adc_pwr(adc, true);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct dev_pm_ops rzg2l_adc_pm_ops = {
> > + SET_RUNTIME_PM_OPS(rzg2l_adc_pm_runtime_suspend,
> > + rzg2l_adc_pm_runtime_resume,
> > + NULL)
> > +};
> > +
> > +static struct platform_driver rzg2l_adc_driver = {
> > + .probe = rzg2l_adc_probe,
> > + .remove = rzg2l_adc_remove,
> > + .driver = {
> > + .name = DRIVER_NAME,
> > + .of_match_table = rzg2l_adc_match,
> > + .pm = &rzg2l_adc_pm_ops,
> > + },
> > +};
> > +
> > +module_platform_driver(rzg2l_adc_driver);
> > +
> > +MODULE_AUTHOR("Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>");
> > +MODULE_DESCRIPTION("Renesas RZ/G2L ADC driver");
> > +MODULE_LICENSE("GPL v2");
>
