Re: [PATCH 2/2] iio: adc: Add support for TI INA260 power monitors

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 3/22/21 1:11 PM, Raviteja Narayanam wrote:

-----Original Message-----
From: Lars-Peter Clausen <lars@xxxxxxxxxx>
Sent: Monday, March 22, 2021 5:22 PM
To: Raviteja Narayanam <rna@xxxxxxxxxx>; robh+dt@xxxxxxxxxx;
jic23@xxxxxxxxxx
Cc: Michal Simek <michals@xxxxxxxxxx>; pmeerw@xxxxxxxxxx; linux-
iio@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; linux-
kernel@xxxxxxxxxxxxxxx; git <git@xxxxxxxxxx>; Shubhrajyoti Datta
<shubhraj@xxxxxxxxxx>
Subject: Re: [PATCH 2/2] iio: adc: Add support for TI INA260 power monitors

On 3/22/21 12:43 PM, Lars-Peter Clausen wrote:
On 3/22/21 11:50 AM, Raviteja Narayanam wrote:
This driver supports software buffer mode and raw reads of ina260 iio
channels.

In software buffer mode, a kthread will capture the active
scan_elements periodically using a delay. This can produce a stream
of up to 3 channels plus a 64 bits timestamp based on the scan_elements.

Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xxxxxxxxxx>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xxxxxxxxxx>
Hi,

Thanks for that patch, it looks really good.

Looking at the datasheet the part seems to be very similar to the
ina226 from a software interface point of view. Looks like the current
and calibration register are missing and the scales are a bit different.

We already have a driver for the ina226 (adc-ina2xx) and it looks like
your driver is also inspired by it. Have you considered adding support
for the ina260 to the existing driver? This will reduce the amount of
duplicated code.
To add to that this driver has some nice new features and bug fixes that are
not in the ina2xx driver, like debug register access. But the ina2xx has also
seen a fair amount of improvements since this driver was branched off of it.
It would be nice to get the best of both in a single driver.
Thanks for the review Lars.
Yes, using ina2xx driver was the first preference but after this discussion (https://www.spinics.net/lists/devicetree/msg354475.html ),
we have started a new driver as ina260 was considered to be sufficiently different from ina2xx.

Can you elaborate where you see the significant difference? When I look at the code the drivers are >90% identical.

I believe pretty much all we need to support the ina260 in the existing driver is to add a new iio_chan_spec and ina2xx_config for it. And then some minor tweaks to other parts of the driver, e.g. to make calibration optional. I believe this can be done in ~50 lines of code without making the structure of the driver more cluttered.


Regards,
Raviteja N

- Lars

---
   MAINTAINERS                  |   8 +
   drivers/iio/adc/Kconfig      |  12 +
   drivers/iio/adc/Makefile     |   1 +
   drivers/iio/adc/ina260-adc.c | 556
+++++++++++++++++++++++++++++++++++
   4 files changed, 577 insertions(+)
   create mode 100644 drivers/iio/adc/ina260-adc.c

diff --git a/MAINTAINERS b/MAINTAINERS index
aa84121c5611..768a4b148035 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8760,6 +8760,14 @@ F:    Documentation/hwmon/ina2xx.rst
   F:    drivers/hwmon/ina2xx.c
   F:    include/linux/platform_data/ina2xx.h
   +INA260 POWER MONITOR DRIVER
+M:    Raviteja Narayanam <raviteja.narayanam@xxxxxxxxxx>
+R:    Shubhrajyoti Datta <shubhrajyoti.datta@xxxxxxxxxx>
+R:    Michal Simek <michal.simek@xxxxxxxxxx>
+S:    Maintained
+F:    Documentation/devicetree/bindings/iio/adc/ti,ina260.yaml
+F:    drivers/iio/adc/ina260-adc.c
+
   INDUSTRY PACK SUBSYSTEM (IPACK)
   M:    Samuel Iglesias Gonsalvez <siglesias@xxxxxxxxxx>
   M:    Jens Taprogge <jens.taprogge@xxxxxxxxxxxx> diff --git
a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig index
bf7d22fa4be2..f6f8fd6bd113 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -497,6 +497,18 @@ config INA2XX_ADC
         Say yes here to build support for TI INA2xx family of Power
Monitors.
         This driver is mutually exclusive with the HWMON version.
   +config INA260_ADC
+    tristate "Texas Instruments INA260 Power Monitors IIO driver"
+    depends on I2C
+    select REGMAP_I2C
+    select IIO_BUFFER
+    select IIO_KFIFO_BUF
+    help
+      Say yes here to build support for TI INA260 power monitor.
+      This driver can also be built as a module. It supports
software buffer
+      mode and raw reads of ina260 iio channels. Up to 4 channels
+are
+      supported including timestamp.
+
   config INGENIC_ADC
       tristate "Ingenic JZ47xx SoCs ADC driver"
       depends on MIPS || COMPILE_TEST diff --git
a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile index
5fca90ada0ec..a3bbcad64a41 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -47,6 +47,7 @@ obj-$(CONFIG_HI8435) += hi8435.o
   obj-$(CONFIG_HX711) += hx711.o
   obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
   obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o
+obj-$(CONFIG_INA260_ADC) += ina260-adc.o
   obj-$(CONFIG_INGENIC_ADC) += ingenic-adc.o
   obj-$(CONFIG_INTEL_MRFLD_ADC) += intel_mrfld_adc.o
   obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o diff --git
a/drivers/iio/adc/ina260-adc.c b/drivers/iio/adc/ina260-adc.c new
file mode 100644 index 000000000000..7f74aa94fd31
--- /dev/null
+++ b/drivers/iio/adc/ina260-adc.c
@@ -0,0 +1,556 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * INA260 power monitor driver
+ * Based on drivers/iio/adc/ina2xx-adc.c
+ *
+ * Copyright (C) 2021 Xilinx, Inc.
+ */
+
+#include <linux/i2c.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/kfifo_buf.h>
+#include <linux/iio/sysfs.h>
+#include <linux/kthread.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/sched/task.h>
+#include <linux/util_macros.h>
+
+/* INA260 registers definition */
+#define INA260_CONFIG        0x00
+#define INA260_CURRENT        0x01
+#define INA260_VOLTAGE        0x02
+#define INA260_POWER        0x03
+#define INA260_MASK_ENABLE    0x06
+#define INA260_ALERT_LIMIT    0x07
+#define INA260_MANF_ID        0xFE
+#define INA260_DIE_ID        0xFF
+
+#define INA260_CONFIG_DEFAULT    0x6327
+
+#define INA260_CURRENT_LSB    1250
+#define INA260_VOLTAGE_LSB    1250
+#define INA260_POWER_LSB    10
+
+/* Bits */
+#define INA260_CVRF        BIT(3)
+
+#define INA260_MODE_MASK    GENMASK(2, 0) #define
INA260_VOLT_MASK
+GENMASK(8, 6) #define INA260_SHIFT_VOLT(val)    ((val) << 6) #define
+INA260_CURR_MASK    GENMASK(5, 3) #define
INA260_SHIFT_CURR(val)
+((val) << 3) #define INA260_AVG_MASK        GENMASK(11, 9) #define
+INA260_SHIFT_AVG(val)    ((val) << 9)
+
+#define SAMPLING_PERIOD(x) ({        \
+    typeof(x) _x = (x);        \
+    (_x->config->volt_conv_time    \
+    + _x->config->curr_conv_time)    \
+    * _x->config->avgs; })
+
+static bool ina260_is_writeable_reg(struct device *dev, unsigned int
reg)
+{
+    return (reg == INA260_CONFIG) || (reg == INA260_MASK_ENABLE) ||
+        (reg == INA260_ALERT_LIMIT); }
+
+static bool ina260_is_volatile_reg(struct device *dev, unsigned int
reg)
+{
+    return (reg != INA260_CONFIG);
+}
+
+static inline bool is_signed_reg(unsigned int reg) {
+    return (reg == INA260_CURRENT);
+}
+
+static const struct regmap_config ina260_regmap_config = {
+    .reg_bits = 8,
+    .val_bits = 16,
+    .max_register = 8,
+    .writeable_reg = ina260_is_writeable_reg,
+    .volatile_reg = ina260_is_volatile_reg, };
+
+enum ina260_ids {ina260 = 0};
+
+/**
+ * struct ina260_config - For configurable parameters
+ * @config_default: Default configuration
+ * @volt_conv_time: Bus voltage conversion time
+ * @curr_conv_time: Shunt current conversion time
+ * @avgs: Number of samples collected and averaged  */ struct
+ina260_config {
+    u16 config_default;
+    int volt_conv_time;
+    int curr_conv_time;
+    int avgs;
+};
+
+/**
+ * struct ina260_chip - For device specific data
+ * @regmap: Regmap pointer to device registers
+ * @task: Pointer to task created by buffer mode
+ * @lock: Mutex to enable use of multiple user apps
+ * @chip_id: Id to determine chip
+ * @config: Pointer to config structure  */ struct ina260_chip {
+    struct regmap *regmap;
+    struct task_struct *task;
+    struct mutex lock; /* Lock for device writes */
+    enum ina260_ids chip_id;
+    struct ina260_config *config;
+};
+
+static struct ina260_config ina260_config[] = {
+    [ina260] = {
+        .config_default = INA260_CONFIG_DEFAULT,
+        .volt_conv_time = 1100,
+        .curr_conv_time = 1100,
+        .avgs = 4,
+    },
+};
+
+static int ina260_read_raw(struct iio_dev *indio_dev,
+               struct iio_chan_spec const *chan,
+               int *val, int *val2, long mask) {
+    struct ina260_chip *chip = iio_priv(indio_dev);
+    unsigned int regval;
+    int ret;
+
+    switch (mask) {
+    case IIO_CHAN_INFO_RAW:
+        if (iio_buffer_enabled(indio_dev))
+            return -EBUSY;
+
+        ret = regmap_read(chip->regmap, chan->address, &regval);
+        if (ret)
+            return ret;
+
+        if (is_signed_reg(chan->address))
+            *val = (s16)regval;
+        else
+            *val = regval;
+        return IIO_VAL_INT;
+
+    case IIO_CHAN_INFO_SCALE:
+        switch (chan->address) {
+        case INA260_CURRENT:
+            *val = INA260_CURRENT_LSB;
+            *val2 = 1000;
+            return IIO_VAL_FRACTIONAL;
+
+        case INA260_VOLTAGE:
+            *val = INA260_VOLTAGE_LSB;
+            *val2 = 1000;
+            return IIO_VAL_FRACTIONAL;
+
+        case INA260_POWER:
+            *val = INA260_POWER_LSB;
+            return IIO_VAL_INT;
+        }
+        return -EINVAL;
+
+    case IIO_CHAN_INFO_INT_TIME:
+        *val = 0;
+        if (chan->address == INA260_VOLTAGE)
+            *val2 = chip->config->volt_conv_time;
+        else
+            *val2 = chip->config->curr_conv_time;
+
+        return IIO_VAL_INT_PLUS_MICRO;
+
+    case IIO_CHAN_INFO_SAMP_FREQ:
+        *val = DIV_ROUND_CLOSEST(1000000, SAMPLING_PERIOD(chip));
+        return IIO_VAL_INT;
+
+    case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+        *val = chip->config->avgs;
+        return IIO_VAL_INT;
+    }
+
+    return -EINVAL;
+}
+
+static const int ina260_avg_tab[] = { 1, 4, 16, 64, 128, 256, 512,
1024 };
+
+/* Conversion times in uS */
+static const int ina260_conv_time_tab[] = { 140, 204, 332, 588,
1100, 2116, 4156, 8244 };
+
+static int ina260_write_raw(struct iio_dev *indio_dev,
+                struct iio_chan_spec const *chan,
+                int val, int val2, long mask) {
+    struct ina260_chip *chip = iio_priv(indio_dev);
+    unsigned int config;
+    int ret, bits;
+
+    if (iio_buffer_enabled(indio_dev))
+        return -EBUSY;
+
+    mutex_lock(&chip->lock);
+
+    ret = regmap_read(chip->regmap, INA260_CONFIG, &config);
+    if (ret)
+        goto err;
+
+    switch (mask) {
+    case IIO_CHAN_INFO_INT_TIME:
+        if (val2 > 8244 || val2 < 140) {
+            ret = -EINVAL;
+            goto err;
+        }
+
+        bits = find_closest(val2, ina260_conv_time_tab,
+                    ARRAY_SIZE(ina260_conv_time_tab));
+
+        if (chan->address == INA260_VOLTAGE) {
+            chip->config->volt_conv_time =
+ina260_conv_time_tab[bits];
+            config &= ~INA260_VOLT_MASK;
+            config |= INA260_SHIFT_VOLT(bits) & INA260_VOLT_MASK;
+        } else {
+            chip->config->curr_conv_time =
+ina260_conv_time_tab[bits];
+            config &= ~INA260_CURR_MASK;
+            config |= INA260_SHIFT_CURR(bits) & INA260_CURR_MASK;
+        }
+        break;
+
+    case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+        bits = find_closest(val, ina260_avg_tab,
ARRAY_SIZE(ina260_avg_tab));
+        chip->config->avgs = ina260_avg_tab[bits];
+        config &= ~INA260_AVG_MASK;
+        config |= INA260_SHIFT_AVG(bits) & INA260_AVG_MASK;
+        break;
+
+    default:
+        ret = -EINVAL;
+    }
+    if (!ret)
+        ret = regmap_write(chip->regmap, INA260_CONFIG, config);
+err:
+    mutex_unlock(&chip->lock);
+
+    return ret;
+}
+
+static int ina260_debug_reg(struct iio_dev *indio_dev,
+                unsigned int reg, unsigned int writeval, unsigned
int *readval)
+{
+    struct ina260_chip *chip = iio_priv(indio_dev);
+
+    if (!readval)
+        return regmap_write(chip->regmap, reg, writeval);
+
+    return regmap_read(chip->regmap, reg, readval); }
+
+#define INA260_CHAN_VOLTAGE(_index, _address) { \
+    .type = IIO_VOLTAGE, \
+    .address = (_address), \
+    .indexed = 1, \
+    .channel = (_index), \
+    .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+    BIT(IIO_CHAN_INFO_SCALE) | \
+    BIT(IIO_CHAN_INFO_INT_TIME), \
+    .info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
+    BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
+    .scan_index = (_index), \
+    .scan_type = { \
+        .sign = 'u', \
+        .realbits = 16, \
+        .storagebits = 16, \
+        .endianness = IIO_CPU, \
+    } \
+}
+
+#define INA260_CHAN_CURRENT(_index, _address) { \
+    .type = IIO_CURRENT, \
+    .address = (_address), \
+    .indexed = 1, \
+    .channel = (_index), \
+    .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+    BIT(IIO_CHAN_INFO_SCALE) | \
+    BIT(IIO_CHAN_INFO_INT_TIME), \
+    .info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
+    BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
+    .scan_index = (_index), \
+    .scan_type = { \
+        .sign = 's', \
+        .realbits = 16, \
+        .storagebits = 16, \
+        .endianness = IIO_CPU, \
+    } \
+}
+
+#define INA260_CHAN_POWER(_index, _address) { \
+    .type = IIO_POWER, \
+    .address = (_address), \
+    .indexed = 1, \
+    .channel = (_index), \
+    .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+    BIT(IIO_CHAN_INFO_SCALE), \
+    .info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
+    BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
+    .scan_index = (_index), \
+    .scan_type = { \
+        .sign = 'u', \
+        .realbits = 16, \
+        .storagebits = 16, \
+        .endianness = IIO_CPU, \
+    } \
+}
+
+static const struct iio_chan_spec ina260_channels[] = {
+    INA260_CHAN_CURRENT(0, INA260_CURRENT),
+    INA260_CHAN_VOLTAGE(1, INA260_VOLTAGE),
+    INA260_CHAN_POWER(2, INA260_POWER),
+    IIO_CHAN_SOFT_TIMESTAMP(3),
+};
+
+/* Possible integration times for current and voltage */ static
+IIO_CONST_ATTR_NAMED(ina260_integration_time_available,
+                integration_time_available,
+                "0.000140 0.000204 0.000332 0.000588 0.001100
0.002116 0.004156 0.008244");
+
+static struct attribute *ina260_attributes[] = {
+&iio_const_attr_ina260_integration_time_available.dev_attr.attr,
+    NULL,
+};
+
+static const struct attribute_group ina260_attribute_group = {
+    .attrs = ina260_attributes,
+};
+
+static const struct iio_info ina260_info = {
+    .attrs = &ina260_attribute_group,
+    .read_raw = ina260_read_raw,
+    .write_raw = ina260_write_raw,
+    .debugfs_reg_access = ina260_debug_reg, };
+
+static int ina260_conversion_ready(struct iio_dev *indio_dev) {
+    struct ina260_chip *chip = iio_priv(indio_dev);
+    unsigned int alert;
+    int ret;
+
+    ret = regmap_read(chip->regmap, INA260_MASK_ENABLE, &alert);
+    if (ret < 0)
+        return ret;
+
+    return (alert & INA260_CVRF);
+}
+
+static int ina260_work_buffer(struct iio_dev *indio_dev) {
+    /* data buffer needs space for channel data and timestap */
+    unsigned short data[3 + sizeof(s64) / sizeof(short)];
+    struct ina260_chip *chip = iio_priv(indio_dev);
+    int bit, ret, i = 0;
+    s64 time;
+
+    time = iio_get_time_ns(indio_dev);
+
+    /*
+     * Read current, voltage and power from device
+     */
+    for_each_set_bit(bit, indio_dev->active_scan_mask,
+             indio_dev->masklength) {
+        unsigned int val;
+
+        ret = regmap_read(chip->regmap, INA260_CURRENT + bit, &val);
+        if (ret < 0)
+            return ret;
+
+        data[i++] = val;
+    }
+
+    iio_push_to_buffers_with_timestamp(indio_dev, data, time);
+
+    return 0;
+}
+
+static int ina260_capture_thread(void *data) {
+    struct iio_dev *indio_dev = data;
+    struct ina260_chip *chip = iio_priv(indio_dev);
+    int sampling_us = SAMPLING_PERIOD(chip);
+    struct timespec64 next, now, delta;
+    s64 delay_us;
+    int ret;
+
+    ktime_get_ts64(&next);
+
+    do {
+        while (1) {
+            /* Check if conversion is ready */
+            ret = ina260_conversion_ready(indio_dev);
+            if (ret < 0)
+                return ret;
+
+            /*
+             * If the conversion was not yet finished,
+             * reset the reference timestamp.
+             */
+            if (ret == 0)
+                ktime_get_ts64(&next);
+            else
+                break;
+        }
+        /* Read the data from sensor and push it to buffers */
+        ret = ina260_work_buffer(indio_dev);
+        if (ret < 0)
+            return ret;
+
+        ktime_get_ts64(&now);
+        /*
+         * Advance the timestamp for the next poll by one sampling
+         * interval, and sleep for the remainder (next - now)
+         * In case "next" has already passed, the interval is added
+         * multiple times, i.e. samples are dropped.
+         */
+        do {
+            timespec64_add_ns(&next, 1000 * sampling_us);
+            delta = timespec64_sub(next, now);
+            delay_us = div_s64(timespec64_to_ns(&delta), 1000);
+        } while (delay_us <= 0);
+
+        usleep_range(delay_us, (delay_us * 3) >> 1);
+
+    } while (!kthread_should_stop());
+
+    return 0;
+}
+
+static int ina260_buffer_enable(struct iio_dev *indio_dev) {
+    struct ina260_chip *chip = iio_priv(indio_dev);
+    unsigned int sampling_us = SAMPLING_PERIOD(chip);
+    struct task_struct *task;
+
+    task = kthread_create(ina260_capture_thread, (void *)indio_dev,
+                  "%s:%d-%uus", indio_dev->name, indio_dev->id,
+                  sampling_us);
+
+    if (IS_ERR(task))
+        return PTR_ERR(task);
+
+    get_task_struct(task);
+    wake_up_process(task);
+    chip->task = task;
+
+    return 0;
+}
+
+static int ina260_buffer_disable(struct iio_dev *indio_dev) {
+    struct ina260_chip *chip = iio_priv(indio_dev);
+
+    if (chip->task) {
+        kthread_stop(chip->task);
+        put_task_struct(chip->task);
+        chip->task = NULL;
+    }
+
+    return 0;
+}
+
+static const struct iio_buffer_setup_ops ina260_setup_ops = {
+    .postenable = &ina260_buffer_enable,
+    .predisable = &ina260_buffer_disable, };
+
+static int ina260_probe(struct i2c_client *client, const struct
i2c_device_id *id)
+{
+    struct iio_dev *indio_dev;
+    struct iio_buffer *buffer;
+    struct ina260_chip *chip;
+    enum ina260_ids type = 0;
+    int ret;
+
+    indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip));
+    if (!indio_dev)
+        return -ENOMEM;
+
+    chip = iio_priv(indio_dev);
+    i2c_set_clientdata(client, indio_dev);
+
+    chip->regmap = devm_regmap_init_i2c(client,
+&ina260_regmap_config);
+    if (IS_ERR(chip->regmap)) {
+        dev_err(&client->dev, "failed to allocate register map\n");
+        return PTR_ERR(chip->regmap);
+    }
+
+    mutex_init(&chip->lock);
+
+    indio_dev->modes = INDIO_DIRECT_MODE |
INDIO_BUFFER_SOFTWARE;
+    indio_dev->dev.parent = &client->dev;
+    indio_dev->dev.of_node = client->dev.of_node;
+
+    chip->config = &ina260_config[type];
+    ret = regmap_write(chip->regmap, INA260_CONFIG,
+               chip->config->config_default);
+    if (ret) {
+        dev_err(&client->dev, "Error configuring the device\n");
+        return ret;
+    }
+    indio_dev->channels = ina260_channels;
+    indio_dev->num_channels = ARRAY_SIZE(ina260_channels);
+    indio_dev->info = &ina260_info;
+    indio_dev->name = id->name;
+    indio_dev->setup_ops = &ina260_setup_ops;
+
+    buffer = devm_iio_kfifo_allocate(&indio_dev->dev);
+    if (!buffer)
+        return -ENOMEM;
+
+    iio_device_attach_buffer(indio_dev, buffer);
+
+    return iio_device_register(indio_dev); }
+
+static int ina260_remove(struct i2c_client *client) {
+    struct iio_dev *indio_dev = i2c_get_clientdata(client);
+    struct ina260_chip *chip = iio_priv(indio_dev);
+
+    iio_device_unregister(indio_dev);
+    /* Power down */
+    return regmap_update_bits(chip->regmap, INA260_CONFIG,
INA260_MODE_MASK, 0);
+}
+
+static const struct i2c_device_id ina260_id[] = {
+    {"ina260", ina260},
+    {}
+};
+MODULE_DEVICE_TABLE(i2c, ina260_id);
+
+static const struct of_device_id ina260_of_match[] = {
+    {
+        .compatible = "ti,ina260",
+        .data = (void *)ina260
+    },
+    {},
+};
+MODULE_DEVICE_TABLE(of, ina260_of_match);
+
+static struct i2c_driver ina260_driver = {
+    .driver = {
+        .name = "ina260-adc",
+        .of_match_table = ina260_of_match,
+    },
+    .probe = ina260_probe,
+    .remove = ina260_remove,
+    .id_table = ina260_id,
+};
+module_i2c_driver(ina260_driver);
+
+MODULE_AUTHOR("Raviteja Narayanam
<raviteja.narayanam@xxxxxxxxxx>");
+MODULE_DESCRIPTION("Texas Instruments INA 260 ADC driver");
+MODULE_LICENSE("GPL v2");





[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux