Re: [PATCH 1/2] iio: documentation: Document proximity sensor label use

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On 2/15/21 1:39 PM, Jonathan Cameron wrote:
> On Fri, 12 Feb 2021 19:58:47 +0100
> Hans de Goede <hdegoede@xxxxxxxxxx> wrote:
> 
>> Hi,
>>
>> On 2/12/21 7:46 PM, Jonathan Cameron wrote:
>>> On Sun,  7 Feb 2021 13:37:19 +0100
>>> Hans de Goede <hdegoede@xxxxxxxxxx> wrote:
>>>   
>>>> Add an entry to Documentation/ABI/testing/sysfs-bus-iio for
>>>> the new device and channel label sysfs-attribute support.
>>>>
>>>> And document the standardized labels which may be used with proximity
>>>> sensors to hint userspace about the intended use of the sensor.
>>>>
>>>> Using labels to differentiate between the multiple proximity sensors
>>>> which a modern laptop/tablet may have was discussed in this thread:
>>>> https://lore.kernel.org/linux-iio/9f9b0ff6-3bf1-63c4-eb36-901cecd7c4d9@xxxxxxxxxx/
>>>>
>>>> As mentioned the "proximity-wifi*" labels are already being used in
>>>> this manner on some chromebooks, see e.g.:
>>>> arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
>>>> arch/arm64/boot/dts/qcom/sc7180-trogdor-lte-sku.dtsi
>>>>
>>>> And the "proximity-palmrest" and "proximity-lap" labels are intended
>>>> to be used with the lap and palmrest sensors found in recent Lenovo
>>>> ThinkPad models.
>>>>
>>>> Cc: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx>
>>>> Cc: Mark Pearson <mpearson@xxxxxxxxxx>
>>>> Cc: Bastien Nocera <hadess@xxxxxxxxxx>
>>>> Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
>>>> ---
>>>>  Documentation/ABI/testing/sysfs-bus-iio | 41 +++++++++++++++++++++++++
>>>>  1 file changed, 41 insertions(+)
>>>>
>>>> diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
>>>> index 35289d47d6cb..f2f090f8bd2f 100644
>>>> --- a/Documentation/ABI/testing/sysfs-bus-iio
>>>> +++ b/Documentation/ABI/testing/sysfs-bus-iio
>>>> @@ -33,6 +33,47 @@ Description:
>>>>  		Description of the physical chip / device for device X.
>>>>  		Typically a part number.
>>>>  
>>>> +What:		/sys/bus/iio/devices/iio:deviceX/label
>>>> +What:		/sys/bus/iio/devices/iio:deviceX/in_*_label
>>>> +What:		/sys/bus/iio/devices/iio:deviceX/out_*_label  
>>>
>>> I was a bit in two minds about this from an organizational point of view.
>>> 1) Whether to separate the general label where position tends to make sense
>>>    from the channel labels.  May be something we want to do in future but we can probably
>>>    let that go for now.
>>> 2) Whether to allow such broad wild cards for the channels.
>>>    Whilst in theory any channel can have a label we normally only document ABI
>>>    that actually exists (mostly to know what we might break if we change anything :)
>>>    Still I can't see any way we can change this without breakage so in this
>>>    one case let's let the broad wild card go in.
>>>
>>> This comes unstuck on the fact it overlaps with existing more specific Docs.
>>>
>>> So can you pull the channel part out of here for v2.
>>> /sys/bus/iio/devices/iio:deviceX/in_voltageY_label
>>> /sys/bus/iio/devices/iio:deviceX/in_anglY_label  
>>
>> The problem is that these labels may either be used on a whole device,
>> which is certainly the case with the accelerometers in patch 2/2 where
>> the x y and z channels obviously all are either "accel-base" or
>> "accel-display".
>>
>> Where as for proximity sensors the labels could be either applied at the
>> device level, or at a channel level.
>>
>> The existing chromebook proximity usage is applying a label for this
>> at the device level.
>>
>> This does mean that atm all users of this are using device-level labels;
> 
> Not at all, but some (possibly all?) are separately documented in two
> existing entries. The generic version you propose overlaps with them
> and that is what I'd like to avoid.
> 
> We could group these into the same 'catch all' element, but I suspect
> the text will just grow too large over time, so I'd like to keep them
> as broken up as possible.
> 
> What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_label
> What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_label
> 
> What:		/sys/bus/iio/devices/iio:deviceX/in_anglY_label
> 
>> and maybe I'm reading too much in your request. I guess that for now
>> I can just drop these lines for v2 :
>>
>> What:		/sys/bus/iio/devices/iio:deviceX/in_*_label
>> What:		/sys/bus/iio/devices/iio:deviceX/out_*_label
>>
>> Is that what you have in mind ?
>>
>> Or do you want me to split this up in a proximity sensor case and an
>> accel case, and group both cases together with other proximity / accel
>> sensor attributes ?
> 
> Yes, that would be ideal for the cases where we have separate
> channel labels, but if we aren't using them today, lets introduce them
> when they are needed.

Right, so atm we do not have any channel labels only device labels,
which means there is only 1 "What:".

What:		/sys/bus/iio/devices/iio:deviceX/label

For which v1 (this version) of this series adds a single large
text block which covers both proximity and accelerometers.

So just to be clear, you want me to split this, resulting in 2
entries with identical "What:" labels:

What:		/sys/bus/iio/devices/iio:deviceX/label

And then group the 2 text blocks together with other proximity
sensor attributes, resp. other accelerometer attributes ?

Regards,

Hans







> 
> Jonathan
> 
> 
>>
>> Regards,
>>
>> Hans
>>
>>
>>
>>
>>> Jonathan  
>>>> +KernelVersion:	5.8
>>>> +Contact:	linux-iio@xxxxxxxxxxxxxxx
>>>> +Description:
>>>> +		Optional symbolic label for a device or a channel.
>>>> +		This is useful for userspace to be able to better identify an
>>>> +		individual device or channel.
>>>> +
>>>> +		The contents of the label are free-form, but there are some
>>>> +		standardized uses:
>>>> +
>>>> +		For proximity sensors which give the proximity (of a person) to
>>>> +		a certain wlan or wwan antenna the following standardized labels
>>>> +		are used:
>>>> +
>>>> +		* "proximity-wifi"
>>>> +		* "proximity-lte"
>>>> +		* "proximity-wifi-lte"
>>>> +		* "proximity-wifi-left"
>>>> +		* "proximity-wifi-right"
>>>> +
>>>> +		These are used to indicate to userspace that these proximity
>>>> +		sensors may be used to tune transmit power to ensure that
>>>> +		Specific Absorption Rate (SAR) limits are honored.
>>>> +		The "-left" and "-right" labels are for devices with multiple
>>>> +		antennas.
>>>> +
>>>> +		In some laptops/tablets the standardized proximity sensor labels
>>>> +		instead	indicate proximity to a specific part of the device:
>>>> +
>>>> +		* "proximity-palmrest" indicates proximity to the keyboard's palmrest
>>>> +		* "proximity-palmrest-left" indicates proximity to the left part of the palmrest
>>>> +		* "proximity-palmrest-right" indicates proximity to the right part of the palmrest
>>>> +		* "proximity-lap" indicates the device is being used on someone's lap
>>>> +
>>>> +		Note "proximity-lap" is special in that its value may be
>>>> +		calculated by firmware from other sensor readings, rather then
>>>> +		being a raw sensor reading.
>>>> +
>>>>  What:		/sys/bus/iio/devices/iio:deviceX/current_timestamp_clock
>>>>  KernelVersion:	4.5
>>>>  Contact:	linux-iio@xxxxxxxxxxxxxxx  
>>>   
>>
> 




[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux