[PATCH 09/10] dt-bindings:iio:light:capella,cm3605: txt to yaml conversion.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>

Simple conversion using the new iio-consumers.yaml binding in the
dt-schema.

Signed-off-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
Cc: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
 .../bindings/iio/light/capella,cm3605.yaml    | 78 +++++++++++++++++++
 .../devicetree/bindings/iio/light/cm3605.txt  | 41 ----------
 2 files changed, 78 insertions(+), 41 deletions(-)

diff --git a/Documentation/devicetree/bindings/iio/light/capella,cm3605.yaml b/Documentation/devicetree/bindings/iio/light/capella,cm3605.yaml
new file mode 100644
index 000000000000..001c99dbd14e
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/capella,cm3605.yaml
@@ -0,0 +1,78 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/light/capella,cm3605.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title:
+  Capella Microsystems CM3605 Ambient Light and Short Distance Proximity Sensor
+
+maintainers:
+  - Linus Walleij <linus.walleij@xxxxxxxxxx>
+
+description: |
+  The CM3605 is an entirely analog part. However, it requires quite a bit of
+  software logic to interface a host operating system.
+
+  This ALS and proximity sensor was one of the very first deployed in mobile
+  handsets, notably it is used in the very first Nexus One Android phone from
+  2010.
+
+properties:
+  compatible:
+    const: capella,cm3605
+
+  aset-gpios:
+    maxItems: 1
+    description:
+      ASET line (drive low to activate the ALS, should be flagged
+      GPIO_ACTIVE_LOW)
+
+  interrupts:
+    maxItems: 1
+    description:
+      Connected to the POUT (proximity sensor out) line. The edge
+      detection must be set to IRQ_TYPE_EDGE_BOTH so as to detect
+      movements toward and away from the proximity sensor.
+
+  io-channels:
+    maxItems: 1
+    description:
+      ADC channel used for converting the voltage from AOUT to a digital
+      representation.
+
+  io-channel-names:
+    const: aout
+
+  vdd-supply: true
+
+  capella,aset-resistance-ohms:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [50000, 100000, 300000, 600000]
+    description: >
+      Sensitivity calibration resistance. Note that calibration curves
+      are only provided for specific allowed values. Default: 100 kOhms.
+
+required:
+  - compatible
+  - aset-gpios
+  - interrupts
+  - io-channels
+  - io-channel-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    light-sensor {
+        compatible = "capella,cm3605";
+        vdd-supply = <&foo_reg>;
+        aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>;
+        capella,aset-resistance-ohms = <100000>;
+        interrupts = <1 IRQ_TYPE_EDGE_BOTH>;
+        io-channels = <&adc 0x01>;
+        io-channel-names = "aout";
+    };
+...
diff --git a/Documentation/devicetree/bindings/iio/light/cm3605.txt b/Documentation/devicetree/bindings/iio/light/cm3605.txt
deleted file mode 100644
index 56331a79f9ab..000000000000
--- a/Documentation/devicetree/bindings/iio/light/cm3605.txt
+++ /dev/null
@@ -1,41 +0,0 @@
-Capella Microsystems CM3605
-Ambient Light and Short Distance Proximity Sensor
-
-The CM3605 is an entirely analog part which however require quite a bit of
-software logic to interface a host operating system.
-
-This ALS and proximity sensor was one of the very first deployed in mobile
-handsets, notably it is used in the very first Nexus One Android phone from
-2010.
-
-Required properties:
-- compatible: must be: "capella,cm3605"
-- aset-gpios: GPIO line controlling the ASET line (drive low
-  to activate the ALS, should be flagged GPIO_ACTIVE_LOW)
-- interrupts: the IRQ line (such as a GPIO) that is connected to
-  the POUT (proximity sensor out) line. The edge detection must
-  be set to IRQ_TYPE_EDGE_BOTH so as to detect movements toward
-  and away from the proximity sensor.
-- io-channels: the ADC channel used for converting the voltage from
-  AOUT to a digital representation.
-- io-channel-names: must be "aout"
-
-Optional properties:
-- vdd-supply: regulator supplying VDD power to the component.
-- capella,aset-resistance-ohms: the sensitivity calibration resistance,
-  in Ohms. Valid values are: 50000, 100000, 300000 and 600000,
-  as these are the resistance values that we are supplied with
-  calibration curves for. If not supplied, 100 kOhm will be assumed
-  but it is strongly recommended to supply this.
-
-Example:
-
-cm3605 {
-	compatible = "capella,cm3605";
-	vdd-supply = <&foo_reg>;
-	aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>;
-	capella,aset-resistance-ohms = <100000>;
-	interrupts = <1 IRQ_TYPE_EDGE_BOTH>;
-	io-channels = <&adc 0x01>;
-	io-channel-names = "aout";
-};
-- 
2.28.0




[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux