From: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> Simple binding conversion. Only addition was #io-channel-cells to allow for potential consumers of the channels on this device. Signed-off-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> Cc: Akinobu Mita <akinobu.mita@xxxxxxxxx> --- .../bindings/iio/adc/ti,adc12138.yaml | 85 +++++++++++++++++++ .../bindings/iio/adc/ti-adc12138.txt | 37 -------- 2 files changed, 85 insertions(+), 37 deletions(-) diff --git a/Documentation/devicetree/bindings/iio/adc/ti,adc12138.yaml b/Documentation/devicetree/bindings/iio/adc/ti,adc12138.yaml new file mode 100644 index 000000000000..3e8c43aa8ef3 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti,adc12138.yaml @@ -0,0 +1,85 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/ti,adc12138.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments ADC12138 and similar self-calibrating ADCs + +maintainers: + - Akinobu Mita <akinobu.mita@xxxxxxxxx> + +description: | + 13 bit ADCs with 1, 2 or 8 inputs and self calibrating circuitry to + correct for linearity, zero and full scale errors. + +properties: + compatible: + enum: + - ti,adc12130 + - ti,adc12132 + - ti,adc12138 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + description: End of Conversion (EOC) interrupt + + clocks: + maxItems: 1 + description: Conversion clock input. + + spi-max-frequency: true + + vref-p-supply: + description: The regulator supply for positive analog voltage reference + + vref-n-suppy: + description: | + The regulator supply for negative analog voltage reference + (Note that this must not go below GND or exceed vref-p) + If not specified, this is assumed to be analog ground. + + ti,acquisition-time: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 6, 10, 18, 34] + description: | + The number of conversion clock periods for the S/H's acquisition time. + For high source impedances, this value can be increased to 18 or 34. + For less ADC accuracy and/or slower CCLK frequencies this value may be + decreased to 6. See section 6.0 INPUT SOURCE RESISTANCE in the + datasheet for details. + + "#io-channel-cells": + const: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - vref-p-supply + +additionalProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "ti,adc12138"; + reg = <0>; + interrupts = <28 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio1>; + clocks = <&cclk>; + vref-p-supply = <&ldo4_reg>; + spi-max-frequency = <5000000>; + ti,acquisition-time = <6>; + #io-channel-cells = <1>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt deleted file mode 100644 index 049a1d36f013..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/ti-adc12138.txt +++ /dev/null @@ -1,37 +0,0 @@ -* Texas Instruments' ADC12130/ADC12132/ADC12138 - -Required properties: - - compatible: Should be one of - * "ti,adc12130" - * "ti,adc12132" - * "ti,adc12138" - - reg: SPI chip select number for the device - - interrupts: Should contain interrupt for EOC (end of conversion) - - clocks: phandle to conversion clock input - - spi-max-frequency: Definision as per - Documentation/devicetree/bindings/spi/spi-bus.txt - - vref-p-supply: The regulator supply for positive analog voltage reference - -Optional properties: - - vref-n-supply: The regulator supply for negative analog voltage reference - (Note that this must not go below GND or exceed vref-p) - If not specified, this is assumed to be analog ground. - - ti,acquisition-time: The number of conversion clock periods for the S/H's - acquisition time. Should be one of 6, 10, 18, 34. If not specified, - default value of 10 is used. - For high source impedances, this value can be increased to 18 or 34. - For less ADC accuracy and/or slower CCLK frequencies this value may be - decreased to 6. See section 6.0 INPUT SOURCE RESISTANCE in the - datasheet for details. - -Example: -adc@0 { - compatible = "ti,adc12138"; - reg = <0>; - interrupts = <28 IRQ_TYPE_EDGE_RISING>; - interrupt-parent = <&gpio1>; - clocks = <&cclk>; - vref-p-supply = <&ldo4_reg>; - spi-max-frequency = <5000000>; - ti,acquisition-time = <6>; -}; -- 2.28.0
