On Fri, 17 Jul 2020 17:55:32 +0100
Lee Jones <lee.jones@xxxxxxxxxx> wrote:
> No attempt has been made to document any of the demoted functions here.
>
> Fixes the following W=1 kernel build warning(s):
>
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:444: warning: Function parameter or member 'st' not described in 'inv_mpu6050_set_lpf_regs'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:444: warning: Function parameter or member 'val' not described in 'inv_mpu6050_set_lpf_regs'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:480: warning: Function parameter or member 'indio_dev' not described in 'inv_mpu6050_init_config'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:862: warning: Function parameter or member 'st' not described in 'inv_mpu6050_set_lpf'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:862: warning: Function parameter or member 'rate' not described in 'inv_mpu6050_set_lpf'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:893: warning: Function parameter or member 'dev' not described in 'inv_mpu6050_fifo_rate_store'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:893: warning: Function parameter or member 'attr' not described in 'inv_mpu6050_fifo_rate_store'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:893: warning: Function parameter or member 'buf' not described in 'inv_mpu6050_fifo_rate_store'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:893: warning: Function parameter or member 'count' not described in 'inv_mpu6050_fifo_rate_store'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:954: warning: Function parameter or member 'dev' not described in 'inv_fifo_rate_show'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:954: warning: Function parameter or member 'attr' not described in 'inv_fifo_rate_show'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:954: warning: Function parameter or member 'buf' not described in 'inv_fifo_rate_show'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:975: warning: Function parameter or member 'dev' not described in 'inv_attr_show'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:975: warning: Function parameter or member 'attr' not described in 'inv_attr_show'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:975: warning: Function parameter or member 'buf' not described in 'inv_attr_show'
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:1282: warning: Function parameter or member 'st' not described in 'inv_check_and_setup_chip'
>
> Cc: Jean-Baptiste Maneyrol <jmaneyrol@xxxxxxxxxxxxxx>
> Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
Applied.
Thanks,
Jonathan
> ---
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 14 +++++++-------
> 1 file changed, 7 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
> index 4d604fe842e5d..f6b2b2e8f1010 100644
> --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
> +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
> @@ -433,7 +433,7 @@ static int inv_mpu6050_set_gyro_fsr(struct inv_mpu6050_state *st,
> return regmap_write(st->map, st->reg->gyro_config, data);
> }
>
> -/**
> +/*
> * inv_mpu6050_set_lpf_regs() - set low pass filter registers, chip dependent
> *
> * MPU60xx/MPU9150 use only 1 register for accelerometer + gyroscope
> @@ -467,7 +467,7 @@ static int inv_mpu6050_set_lpf_regs(struct inv_mpu6050_state *st,
> return regmap_write(st->map, st->reg->accel_lpf, val);
> }
>
> -/**
> +/*
> * inv_mpu6050_init_config() - Initialize hardware, disable FIFO.
> *
> * Initial configuration:
> @@ -847,7 +847,7 @@ static int inv_mpu6050_write_raw(struct iio_dev *indio_dev,
> return result;
> }
>
> -/**
> +/*
> * inv_mpu6050_set_lpf() - set low pass filer based on fifo rate.
> *
> * Based on the Nyquist principle, the bandwidth of the low
> @@ -884,7 +884,7 @@ static int inv_mpu6050_set_lpf(struct inv_mpu6050_state *st, int rate)
> return 0;
> }
>
> -/**
> +/*
> * inv_mpu6050_fifo_rate_store() - Set fifo rate.
> */
> static ssize_t
> @@ -945,7 +945,7 @@ inv_mpu6050_fifo_rate_store(struct device *dev, struct device_attribute *attr,
> return count;
> }
>
> -/**
> +/*
> * inv_fifo_rate_show() - Get the current sampling rate.
> */
> static ssize_t
> @@ -962,7 +962,7 @@ inv_fifo_rate_show(struct device *dev, struct device_attribute *attr,
> return scnprintf(buf, PAGE_SIZE, "%u\n", fifo_rate);
> }
>
> -/**
> +/*
> * inv_attr_show() - calling this function will show current
> * parameters.
> *
> @@ -1275,7 +1275,7 @@ static const struct iio_info mpu_info = {
> .debugfs_reg_access = &inv_mpu6050_reg_access,
> };
>
> -/**
> +/*
> * inv_check_and_setup_chip() - check and setup chip.
> */
> static int inv_check_and_setup_chip(struct inv_mpu6050_state *st)
