On Mon, 9 Dec 2019 00:38:41 +0000
Jeff LaBundy <jeff@xxxxxxxxxxx> wrote:
> This patch adds support for the Azoteq IQS624 and IQS625 angular position
> sensors, capable of reporting the angle of a rotating shaft down to 1 and
> 10 degrees of accuracy, respectively.
>
> This patch also introduces a home for linear and angular position sensors.
> Unlike resolvers, they are typically contactless and use the Hall effect.
>
> Signed-off-by: Jeff LaBundy <jeff@xxxxxxxxxxx>
Looks good
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
My current assumption is that Lee will take this lot via an immutable branch
in MFD once it's ready. Shout if a different path makes sense.
> ---
> Changes in v2:
> - Merged 'Copyright' and 'Author' lines into one in introductory comments
> - Replaced 'error' with 'ret' throughout
> - Added iqs624_pos_angle_en and iqs624_pos_angle_get to remove duplicate
> logic previously used throughout
> - Refactored the logic in iqs624_pos_notifier and added a lock to safely
> evaluate variables that may change in response to user action
> - Refactored the logic in iqs624_pos_read_raw
> - Added a lock to iqs624_pos_read_event_config to account for cases in which
> the corresponding hardware state is in the process of being updated
> - Refactored the logic in iqs624_pos_write_event_config and read the initial
> angle in case it changed since having first been read in iqs624_pos_init
> - Removed iqs624_pos_init as its logic has since been absorbed elsewhere
> - Removed devm_add_action_or_reset failure message
> - Eliminated tabbed alignment of platform_driver struct members
> - Changed Kconfig "depends on" logic to MFD_IQS62X || COMPILE_TEST
>
> drivers/iio/Kconfig | 1 +
> drivers/iio/Makefile | 1 +
> drivers/iio/position/Kconfig | 19 +++
> drivers/iio/position/Makefile | 7 +
> drivers/iio/position/iqs624-pos.c | 284 ++++++++++++++++++++++++++++++++++++++
> 5 files changed, 312 insertions(+)
> create mode 100644 drivers/iio/position/Kconfig
> create mode 100644 drivers/iio/position/Makefile
> create mode 100644 drivers/iio/position/iqs624-pos.c
>
> diff --git a/drivers/iio/Kconfig b/drivers/iio/Kconfig
> index 5bd5185..d5c073a 100644
> --- a/drivers/iio/Kconfig
> +++ b/drivers/iio/Kconfig
> @@ -88,6 +88,7 @@ source "drivers/iio/orientation/Kconfig"
> if IIO_TRIGGER
> source "drivers/iio/trigger/Kconfig"
> endif #IIO_TRIGGER
> +source "drivers/iio/position/Kconfig"
> source "drivers/iio/potentiometer/Kconfig"
> source "drivers/iio/potentiostat/Kconfig"
> source "drivers/iio/pressure/Kconfig"
> diff --git a/drivers/iio/Makefile b/drivers/iio/Makefile
> index bff682a..1712011 100644
> --- a/drivers/iio/Makefile
> +++ b/drivers/iio/Makefile
> @@ -31,6 +31,7 @@ obj-y += light/
> obj-y += magnetometer/
> obj-y += multiplexer/
> obj-y += orientation/
> +obj-y += position/
> obj-y += potentiometer/
> obj-y += potentiostat/
> obj-y += pressure/
> diff --git a/drivers/iio/position/Kconfig b/drivers/iio/position/Kconfig
> new file mode 100644
> index 0000000..eda67f0
> --- /dev/null
> +++ b/drivers/iio/position/Kconfig
> @@ -0,0 +1,19 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +#
> +# Linear and angular position sensors
> +#
> +# When adding new entries keep the list in alphabetical order
> +
> +menu "Linear and angular position sensors"
> +
> +config IQS624_POS
> + tristate "Azoteq IQS624/625 angular position sensors"
> + depends on MFD_IQS62X || COMPILE_TEST
> + help
> + Say Y here if you want to build support for the Azoteq IQS624
> + and IQS625 angular position sensors.
> +
> + To compile this driver as a module, choose M here: the module
> + will be called iqs624-pos.
> +
> +endmenu
> diff --git a/drivers/iio/position/Makefile b/drivers/iio/position/Makefile
> new file mode 100644
> index 0000000..3cbe7a7
> --- /dev/null
> +++ b/drivers/iio/position/Makefile
> @@ -0,0 +1,7 @@
> +#
> +# Makefile for IIO linear and angular position sensors
> +#
> +
> +# When adding new entries keep the list in alphabetical order
> +
> +obj-$(CONFIG_IQS624_POS) += iqs624-pos.o
> diff --git a/drivers/iio/position/iqs624-pos.c b/drivers/iio/position/iqs624-pos.c
> new file mode 100644
> index 0000000..af629bf5
> --- /dev/null
> +++ b/drivers/iio/position/iqs624-pos.c
> @@ -0,0 +1,284 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Azoteq IQS624/625 Angular Position Sensors
> + *
> + * Copyright (C) 2019 Jeff LaBundy <jeff@xxxxxxxxxxx>
> + */
> +
> +#include <linux/device.h>
> +#include <linux/iio/events.h>
> +#include <linux/iio/iio.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/iqs62x.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/notifier.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#define IQS624_POS_DEG_OUT 0x16
> +
> +#define IQS624_POS_SCALE1 (314159 / 180)
> +#define IQS624_POS_SCALE2 100000
> +
> +struct iqs624_pos_private {
> + struct iqs62x_core *iqs62x;
> + struct notifier_block notifier;
> + struct mutex lock;
> + bool angle_en;
> + u16 angle;
> +};
> +
> +static int iqs624_pos_angle_en(struct iqs62x_core *iqs62x, bool angle_en)
> +{
> + unsigned int event_mask = IQS624_HALL_UI_WHL_EVENT;
> +
> + /*
> + * The IQS625 reports angular position in the form of coarse intervals,
> + * so only interval change events are unmasked. Conversely, the IQS624
> + * reports angular position down to one degree of resolution, so wheel
> + * movement events are unmasked instead.
> + */
> + if (iqs62x->dev_desc->prod_num == IQS625_PROD_NUM)
> + event_mask = IQS624_HALL_UI_INT_EVENT;
> +
> + return regmap_update_bits(iqs62x->map, IQS624_HALL_UI, event_mask,
> + angle_en ? 0 : 0xFF);
> +}
> +
> +static int iqs624_pos_notifier(struct notifier_block *notifier,
> + unsigned long event_flags, void *context)
> +{
> + struct iqs62x_event_data *event_data = context;
> + struct iqs624_pos_private *iqs624_pos;
> + struct iqs62x_core *iqs62x;
> + struct iio_dev *indio_dev;
> + u16 angle = event_data->ui_data;
> + s64 timestamp;
> + int ret;
> +
> + iqs624_pos = container_of(notifier, struct iqs624_pos_private,
> + notifier);
> + indio_dev = iio_priv_to_dev(iqs624_pos);
> + timestamp = iio_get_time_ns(indio_dev);
> +
> + iqs62x = iqs624_pos->iqs62x;
> + if (iqs62x->dev_desc->prod_num == IQS625_PROD_NUM)
> + angle = event_data->interval;
> +
> + mutex_lock(&iqs624_pos->lock);
> +
> + if (event_flags & BIT(IQS62X_EVENT_SYS_RESET)) {
> + ret = iqs624_pos_angle_en(iqs62x, iqs624_pos->angle_en);
> + if (ret) {
> + dev_err(indio_dev->dev.parent,
> + "Failed to re-initialize device: %d\n", ret);
> + ret = NOTIFY_BAD;
> + } else {
> + ret = NOTIFY_OK;
> + }
> + } else if (iqs624_pos->angle_en && (angle != iqs624_pos->angle)) {
> + iio_push_event(indio_dev,
> + IIO_UNMOD_EVENT_CODE(IIO_ANGL, 0,
> + IIO_EV_TYPE_CHANGE,
> + IIO_EV_DIR_NONE),
> + timestamp);
> +
> + iqs624_pos->angle = angle;
> + ret = NOTIFY_OK;
> + } else {
> + ret = NOTIFY_DONE;
> + }
> +
> + mutex_unlock(&iqs624_pos->lock);
> +
> + return ret;
> +}
> +
> +static void iqs624_pos_notifier_unregister(void *context)
> +{
> + struct iqs624_pos_private *iqs624_pos = context;
> + struct iio_dev *indio_dev = iio_priv_to_dev(iqs624_pos);
> + int ret;
> +
> + ret = blocking_notifier_chain_unregister(&iqs624_pos->iqs62x->nh,
> + &iqs624_pos->notifier);
> + if (ret)
> + dev_err(indio_dev->dev.parent,
> + "Failed to unregister notifier: %d\n", ret);
> +}
> +
> +static int iqs624_pos_angle_get(struct iqs62x_core *iqs62x, unsigned int *val)
> +{
> + int ret;
> + __le16 val_buf;
> +
> + if (iqs62x->dev_desc->prod_num == IQS625_PROD_NUM)
> + return regmap_read(iqs62x->map, iqs62x->dev_desc->interval,
> + val);
> +
> + ret = regmap_raw_read(iqs62x->map, IQS624_POS_DEG_OUT, &val_buf,
> + sizeof(val_buf));
> + if (ret)
> + return ret;
> +
> + *val = le16_to_cpu(val_buf);
> +
> + return 0;
> +}
> +
> +static int iqs624_pos_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long mask)
> +{
> + struct iqs624_pos_private *iqs624_pos = iio_priv(indio_dev);
> + struct iqs62x_core *iqs62x = iqs624_pos->iqs62x;
> + unsigned int scale = 1;
> + int ret;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + ret = iqs624_pos_angle_get(iqs62x, val);
> + if (ret)
> + return ret;
> +
> + return IIO_VAL_INT;
> +
> + case IIO_CHAN_INFO_SCALE:
> + if (iqs62x->dev_desc->prod_num == IQS625_PROD_NUM) {
> + ret = regmap_read(iqs62x->map, IQS624_INTERVAL_DIV,
> + &scale);
> + if (ret)
> + return ret;
> + }
> +
> + *val = scale * IQS624_POS_SCALE1;
> + *val2 = IQS624_POS_SCALE2;
> + return IIO_VAL_FRACTIONAL;
> +
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int iqs624_pos_read_event_config(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + enum iio_event_type type,
> + enum iio_event_direction dir)
> +{
> + struct iqs624_pos_private *iqs624_pos = iio_priv(indio_dev);
> + int ret;
> +
> + mutex_lock(&iqs624_pos->lock);
> + ret = iqs624_pos->angle_en;
> + mutex_unlock(&iqs624_pos->lock);
> +
> + return ret;
> +}
> +
> +static int iqs624_pos_write_event_config(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + enum iio_event_type type,
> + enum iio_event_direction dir,
> + int state)
> +{
> + struct iqs624_pos_private *iqs624_pos = iio_priv(indio_dev);
> + struct iqs62x_core *iqs62x = iqs624_pos->iqs62x;
> + unsigned int val;
> + int ret;
> +
> + mutex_lock(&iqs624_pos->lock);
> +
> + ret = iqs624_pos_angle_get(iqs62x, &val);
> + if (ret)
> + goto err_mutex;
> +
> + ret = iqs624_pos_angle_en(iqs62x, state);
> + if (ret)
> + goto err_mutex;
> +
> + iqs624_pos->angle = val;
> + iqs624_pos->angle_en = state;
> +
> +err_mutex:
> + mutex_unlock(&iqs624_pos->lock);
> +
> + return ret;
> +}
> +
> +static const struct iio_info iqs624_pos_info = {
> + .read_raw = &iqs624_pos_read_raw,
> + .read_event_config = iqs624_pos_read_event_config,
> + .write_event_config = iqs624_pos_write_event_config,
> +};
> +
> +static const struct iio_event_spec iqs624_pos_events[] = {
> + {
> + .type = IIO_EV_TYPE_CHANGE,
> + .dir = IIO_EV_DIR_NONE,
> + .mask_separate = BIT(IIO_EV_INFO_ENABLE),
> + },
> +};
> +
> +static const struct iio_chan_spec iqs624_pos_channels[] = {
> + {
> + .type = IIO_ANGL,
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> + BIT(IIO_CHAN_INFO_SCALE),
> + .event_spec = iqs624_pos_events,
> + .num_event_specs = ARRAY_SIZE(iqs624_pos_events),
> + },
> +};
> +
> +static int iqs624_pos_probe(struct platform_device *pdev)
> +{
> + struct iqs62x_core *iqs62x = dev_get_drvdata(pdev->dev.parent);
> + struct iqs624_pos_private *iqs624_pos;
> + struct iio_dev *indio_dev;
> + int ret;
> +
> + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*iqs624_pos));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + iqs624_pos = iio_priv(indio_dev);
> + iqs624_pos->iqs62x = iqs62x;
> +
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->dev.parent = &pdev->dev;
> + indio_dev->channels = iqs624_pos_channels;
> + indio_dev->num_channels = ARRAY_SIZE(iqs624_pos_channels);
> + indio_dev->name = iqs62x->dev_desc->dev_name;
> + indio_dev->info = &iqs624_pos_info;
> +
> + mutex_init(&iqs624_pos->lock);
> +
> + iqs624_pos->notifier.notifier_call = iqs624_pos_notifier;
> + ret = blocking_notifier_chain_register(&iqs624_pos->iqs62x->nh,
> + &iqs624_pos->notifier);
> + if (ret) {
> + dev_err(&pdev->dev, "Failed to register notifier: %d\n", ret);
> + return ret;
> + }
> +
> + ret = devm_add_action_or_reset(&pdev->dev,
> + iqs624_pos_notifier_unregister,
> + iqs624_pos);
> + if (ret)
> + return ret;
> +
> + return devm_iio_device_register(&pdev->dev, indio_dev);
> +}
> +
> +static struct platform_driver iqs624_pos_platform_driver = {
> + .driver = {
> + .name = IQS624_DRV_NAME_POS,
> + },
> + .probe = iqs624_pos_probe,
> +};
> +module_platform_driver(iqs624_pos_platform_driver);
> +
> +MODULE_AUTHOR("Jeff LaBundy <jeff@xxxxxxxxxxx>");
> +MODULE_DESCRIPTION("Azoteq IQS624/625 Angular Position Sensors");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:" IQS624_DRV_NAME_POS);
> --
> 2.7.4
>
