On Thu, 14 Nov 2019 11:09:06 +0100 <tomislav.denis@xxxxxxx> wrote: > From: Tomislav Denis <tomislav.denis@xxxxxxx> > > All Sensors DLH is series of low voltage digital pressure sensors. > Additionally to pressure value sensors deliver a temperature value. > Sensors can be accessed over I2C and SPI, this driver supports > only I2C access. > > Signed-off-by: Tomislav Denis <tomislav.denis@xxxxxxx> Hi Tomislav, A few comments inline. Please check the units of the output against the IIO ABI docs. Some IIO ABI units are non obvious unfortunately! Thanks, Jonathan > --- > MAINTAINERS | 7 + > drivers/iio/pressure/Kconfig | 12 ++ > drivers/iio/pressure/Makefile | 1 + > drivers/iio/pressure/dlh-i2c.c | 322 +++++++++++++++++++++++++++++++++++++++++ > 4 files changed, 342 insertions(+) > create mode 100644 drivers/iio/pressure/dlh-i2c.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 8323258..2a08923 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -668,6 +668,13 @@ S: Maintained > F: Documentation/i2c/busses/i2c-ali1563.rst > F: drivers/i2c/busses/i2c-ali1563.c > > +ALL SENSORS DLH SERIES PRESSURE SENSORS DRIVER > +M: Tomislav Denis <tomislav.denis@xxxxxxx> > +W: http://www.allsensors.com/cad/DS-0355_Rev_B.PDF The specific path is likely to bit rot. So either drop the entry entirely or perhaps W: http://www.allsensors.com/ > +S: Maintained > +L: linux-iio@xxxxxxxxxxxxxxx > +F: drivers/iio/pressure/dlh-i2c.c > + > ALLEGRO DVT VIDEO IP CORE DRIVER > M: Michael Tretter <m.tretter@xxxxxxxxxxxxxx> > R: Pengutronix Kernel Team <kernel@xxxxxxxxxxxxxx> > diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig > index ba420e4..504de3e 100644 > --- a/drivers/iio/pressure/Kconfig > +++ b/drivers/iio/pressure/Kconfig > @@ -53,6 +53,18 @@ config IIO_CROS_EC_BARO > To compile this driver as a module, choose M here: the module > will be called cros_ec_baro. > > +config DLH_I2C > + tristate "All Sensors DLH series low voltage digital pressure sensors" > + depends on I2C > + select IIO_BUFFER > + select IIO_TRIGGERED_BUFFER > + help > + Say yes here to build support for the All Sensors DLH series > + pressure sensors driver. > + > + To compile this driver as a module, choose M here: the module > + will be called dlh-i2c. > + > config DPS310 > tristate "Infineon DPS310 pressure and temperature sensor" > depends on I2C > diff --git a/drivers/iio/pressure/Makefile b/drivers/iio/pressure/Makefile > index d8f5ace..1851a36 100644 > --- a/drivers/iio/pressure/Makefile > +++ b/drivers/iio/pressure/Makefile > @@ -9,6 +9,7 @@ obj-$(CONFIG_BMP280) += bmp280.o > bmp280-objs := bmp280-core.o bmp280-regmap.o > obj-$(CONFIG_BMP280_I2C) += bmp280-i2c.o > obj-$(CONFIG_BMP280_SPI) += bmp280-spi.o > +obj-$(CONFIG_DLH_I2C) += dlh-i2c.o > obj-$(CONFIG_DPS310) += dps310.o > obj-$(CONFIG_IIO_CROS_EC_BARO) += cros_ec_baro.o > obj-$(CONFIG_HID_SENSOR_PRESS) += hid-sensor-press.o > diff --git a/drivers/iio/pressure/dlh-i2c.c b/drivers/iio/pressure/dlh-i2c.c > new file mode 100644 > index 0000000..4ef13c2 > --- /dev/null > +++ b/drivers/iio/pressure/dlh-i2c.c > @@ -0,0 +1,322 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * All Sensors DLH series low voltage digital pressure sensors > + * > + * Copyright (c) 2019 AVL DiTEST GmbH > + * Tomislav Denis <tomislav.denis@xxxxxxx> > + * > + * Datasheet: http://www.allsensors.com/cad/DS-0355_Rev_B.PDF > + */ > + > +#include <linux/module.h> > +#include <linux/delay.h> > +#include <linux/i2c.h> > +#include <linux/iio/iio.h> > +#include <linux/iio/buffer.h> > +#include <linux/iio/trigger_consumer.h> > +#include <linux/iio/triggered_buffer.h> > + > +/* Commands */ > +#define DLH_START_SINGLE 0xAA > + > +/* Status bits */ > +#define DLH_STATUS_OK 0x40 > + > +/* DLH data format */ > +#define DLH_NUM_READ_BYTES 7 > +#define DLH_NUM_DATA_BYTES 3 > +#define DLH_NUM_PR_BITS 24 > +#define DLH_NUM_TEMP_BITS 24 > + > +/* DLH timings */ > +#define DLH_SINGLE_DUT_MS 5 > + > +enum dhl_ids { > + dlhl60d, > + dlhl60g, > +}; > + > +struct dlh_info { > + u8 osdig; /* digital offset factor */ > + unsigned int fss; /* full scale span (inch H2O) */ > +}; > + > +struct dlh_state { > + struct i2c_client *client; > + struct dlh_info info; > + u8 rx_buf[DLH_NUM_READ_BYTES] ____cacheline_aligned; > +}; > + > +static struct dlh_info dlh_info_tbl[] = { > + [dlhl60d] = { > + .osdig = 2, > + .fss = 120, > + }, > + [dlhl60g] = { > + .osdig = 10, > + .fss = 60, > + }, > +}; > + > +static int dlh_i2c_read_direct(struct dlh_state *st, > + unsigned int *pressure, unsigned int *temperature) > +{ > + int ret; > + > + ret = i2c_smbus_write_byte(st->client, DLH_START_SINGLE); > + if (ret) { > + dev_err(&st->client->dev, > + "%s: I2C write byte failed\n", __func__); > + return ret; > + } > + > + mdelay(DLH_SINGLE_DUT_MS); > + > + ret = i2c_master_recv(st->client, st->rx_buf, DLH_NUM_READ_BYTES); > + if (ret < 0) { > + dev_err(&st->client->dev, > + "%s: I2C read block failed\n", __func__); > + return ret; > + } > + > + if (st->rx_buf[0] != DLH_STATUS_OK) { > + dev_err(&st->client->dev, > + "%s: invalid status 0x%02x\n", __func__, st->rx_buf[0]); > + return -EBUSY; > + } > + > + *pressure = be32_to_cpup((u32 *)&st->rx_buf[1]) >> 8; > + *temperature = be32_to_cpup((u32 *)&st->rx_buf[3]) & > + GENMASK(DLH_NUM_TEMP_BITS - 1, 0); > + > + return 0; > +} > + > +static int dlh_i2c_read_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *channel, int *value, > + int *value2, long mask) > +{ > + struct dlh_state *st = iio_priv(indio_dev); > + unsigned int pressure, temperature; > + int ret; > + > + switch (mask) { > + case IIO_CHAN_INFO_RAW: > + if (iio_buffer_enabled(indio_dev)) > + return -EBUSY; > + > + ret = iio_device_claim_direct_mode(indio_dev); > + if (ret) > + return ret; > + > + ret = dlh_i2c_read_direct(st, &pressure, &temperature); > + iio_device_release_direct_mode(indio_dev); > + if (ret) > + return ret; > + > + switch (channel->type) { > + case IIO_PRESSURE: /* inch H2O */ I'm guessing the scale converts that to kilopascals as per Documentation/ABI/testing/sysfs-bus-iio? > + *value = pressure; > + return IIO_VAL_INT; > + > + case IIO_TEMP: /* degrees Celsius */ Base units in IIO for temperature are milli degress Celsius. > + *value = temperature; > + return IIO_VAL_INT; > + > + default: > + return -EINVAL; > + } > + case IIO_CHAN_INFO_SCALE: > + switch (channel->type) { > + case IIO_PRESSURE: > + *value = 125 * st->info.fss; > + *value2 = 100 * (1 << DLH_NUM_PR_BITS); > + return IIO_VAL_FRACTIONAL; > + > + case IIO_TEMP: > + *value = 125; > + *value2 = DLH_NUM_TEMP_BITS; > + return IIO_VAL_FRACTIONAL_LOG2; > + > + default: > + return -EINVAL; > + } > + case IIO_CHAN_INFO_OFFSET: > + switch (channel->type) { > + case IIO_PRESSURE: > + *value = -125 * st->info.fss; > + *value2 = 100 * st->info.osdig; > + return IIO_VAL_FRACTIONAL; > + > + case IIO_TEMP: > + *value = -40; > + return IIO_VAL_INT; > + > + default: > + return -EINVAL; > + } default: return -EINVAL; > + } > + Drop the following. One of the standard build bots complains about this and it is sensible to ensure it was deliberate that not all cases were handled in that switch statement. > + return -EINVAL; > +} > + > +static const struct iio_info dlh_i2c_info = { > + .read_raw = dlh_i2c_read_raw, > +}; > + > +static const struct iio_chan_spec dlh_i2c_channels[] = { > + { > + .type = IIO_PRESSURE, > + .indexed = 1, > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > + .info_mask_shared_by_type = > + BIT(IIO_CHAN_INFO_SCALE) | > + BIT(IIO_CHAN_INFO_OFFSET), > + .scan_index = 0, > + .scan_type = { > + .sign = 'u', > + .realbits = DLH_NUM_PR_BITS, > + .storagebits = 32, > + .shift = 8, > + .endianness = IIO_BE, > + }, > + }, { > + .type = IIO_TEMP, > + .indexed = 1, If setting indexed, even though the default is 0, should probably provide the .channel = 0, to make that explicit. > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > + .info_mask_shared_by_type = > + BIT(IIO_CHAN_INFO_SCALE) | > + BIT(IIO_CHAN_INFO_OFFSET), > + .scan_index = 1, > + .scan_type = { > + .sign = 'u', > + .realbits = DLH_NUM_TEMP_BITS, > + .storagebits = 32, > + .shift = 8, > + .endianness = IIO_BE, > + }, > + } > +}; > + > +static irqreturn_t dlh_i2c_trigger_handler(int irq, void *private) > +{ > + struct iio_poll_func *pf = (struct iio_poll_func *)private; No need to add explicit cast for pointers of type void *. The c spec allows simply struct iio_poll_func *pf = private; > + struct iio_dev *indio_dev = pf->indio_dev; > + struct dlh_state *st = iio_priv(indio_dev); > + int ret; > + unsigned int chn, i = 0; > + __be32 tmp_buf[2]; > + > + ret = i2c_master_recv(st->client, st->rx_buf, DLH_NUM_READ_BYTES); > + if (ret < 0) { > + dev_err(&st->client->dev, > + "%s: I2C read block failed\n", __func__); > + goto out; > + } > + > + if (st->rx_buf[0] != DLH_STATUS_OK) { > + dev_err(&st->client->dev, > + "%s: invalid status 0x%02x\n", __func__, st->rx_buf[0]); > + goto out; > + } > + > + ret = i2c_smbus_write_byte(st->client, DLH_START_SINGLE); > + if (ret) { > + dev_err(&st->client->dev, > + "%s: I2C write byte failed\n", __func__); > + goto out; > + } If I understand the logic here correctly, you are triggering the next capture as part of the previous one. This doesn't sound right as we are using an external trigger. Imagine. Trigger1 - reads whatever is currently in buffer and starts next sample. Wait 5 minutes Trigger2 - reads whatever was captured just after trigger1 not fresh data as we might expect. In particular I suspect you get random stale data for the first read after starting the buffer. The flow should be. Trigger1. Send the DLH_START_SINGLE; poll or wait for interrupt to signal completion of this reading. Read data. Wait for 5 minutes Trigger 2. Send the DLH_START_SINGLE; poll or wait for interrupt to signal completion of this reading. Read data. That should guarantee fresh data whatever the spacing of triggers. If you want to basically get data as quick as possible, the loop trigger will ensure that you call the start asap after the prevous read. > + > + for_each_set_bit(chn, indio_dev->active_scan_mask, > + indio_dev->masklength) { > + memcpy(tmp_buf + i, > + &st->rx_buf[1] + chn * DLH_NUM_DATA_BYTES, > + DLH_NUM_DATA_BYTES); > + i++; > + } > + > + iio_push_to_buffers(indio_dev, tmp_buf); > + > +out: > + iio_trigger_notify_done(indio_dev->trig); > + > + return IRQ_HANDLED; > +} > + > +static int dlh_i2c_probe(struct i2c_client *client, > + const struct i2c_device_id *id) > +{ > + struct dlh_state *st; > + struct iio_dev *indio_dev; > + int ret; > + > + if (!i2c_check_functionality(client->adapter, > + I2C_FUNC_I2C | I2C_FUNC_SMBUS_WRITE_BYTE)) { > + dev_err(&client->dev, > + "adapter doesn't support required i2c functionality\n"); > + return -EOPNOTSUPP; > + } > + > + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*st)); > + if (!indio_dev) { > + dev_err(&client->dev, "failed to allocate iio device\n"); > + return -ENOMEM; > + } > + > + i2c_set_clientdata(client, indio_dev); > + > + st = iio_priv(indio_dev); > + st->info = dlh_info_tbl[id->driver_data]; > + st->client = client; > + > + indio_dev->name = id->name; > + indio_dev->dev.parent = &client->dev; > + indio_dev->dev.of_node = client->dev.of_node; > + indio_dev->info = &dlh_i2c_info; > + indio_dev->modes = INDIO_DIRECT_MODE; > + indio_dev->channels = dlh_i2c_channels; > + indio_dev->num_channels = ARRAY_SIZE(dlh_i2c_channels); > + > + ret = devm_iio_triggered_buffer_setup(&client->dev, indio_dev, > + &iio_pollfunc_store_time, &dlh_i2c_trigger_handler, NULL); > + if (ret) { > + dev_err(&client->dev, "failed to setup iio buffer\n"); > + return ret; > + } > + > + ret = devm_iio_device_register(&client->dev, indio_dev); > + if (ret) { > + dev_err(&client->dev, "failed to register iio device\n"); > + return ret; Drop the return ret; out of the brackets as then we don't need the return 0. if (ret) dev_err(...) return ret; } > + } > + > + return 0; > +} > + > +static const struct of_device_id dlh_i2c_of_match[] = { > + { .compatible = "asc,dlhl60d" }, > + { .compatible = "asc,dlhl60g" }, > + {} > +}; > +MODULE_DEVICE_TABLE(of, dlh_i2c_of_match); > + > +static const struct i2c_device_id dlh_i2c_id[] = { > + { "dlhl60d", dlhl60d }, > + { "dlhl60g", dlhl60g }, > + {} > +}; > +MODULE_DEVICE_TABLE(i2c, dlh_i2c_id); > + > +static struct i2c_driver dlh_i2c_driver = { > + .driver = { > + .name = "dlh_i2c", > + .of_match_table = dlh_i2c_of_match, > + }, > + .probe = dlh_i2c_probe, > + .id_table = dlh_i2c_id, > +}; > +module_i2c_driver(dlh_i2c_driver); > + > +MODULE_AUTHOR("Tomislav Denis <tomislav.denis@xxxxxxx>"); > +MODULE_DESCRIPTION("Driver for All Sensors DLH series pressure sensors"); > +MODULE_LICENSE("GPL v2");
