Add more fields and improve API when EC presents data through ACPI
memory space.
Acked-by: Enric Balletbo i Serra <enric.balletbo@xxxxxxxxxxxxx>
Acked-by: Benson Leung <bleung@xxxxxxxxxxxx>
Reviewed-by: Fabien Lahoudere <fabien.lahoudere@xxxxxxxxxxxxx>
Signed-off-by: Gwendal Grignou <gwendal@xxxxxxxxxxxx>
---
include/linux/mfd/cros_ec_commands.h | 419 +++++++++++++++++++--------
1 file changed, 293 insertions(+), 126 deletions(-)
diff --git a/include/linux/mfd/cros_ec_commands.h b/include/linux/mfd/cros_ec_commands.h
index e97e9e976bd0..575066b90bab 100644
--- a/include/linux/mfd/cros_ec_commands.h
+++ b/include/linux/mfd/cros_ec_commands.h
@@ -83,13 +83,15 @@
/* Unused 0x28 - 0x2f */
#define EC_MEMMAP_SWITCHES 0x30 /* 8 bits */
/* Unused 0x31 - 0x33 */
-#define EC_MEMMAP_HOST_EVENTS 0x34 /* 32 bits */
-/* Reserve 0x38 - 0x3f for additional host event-related stuff */
-/* Battery values are all 32 bits */
+#define EC_MEMMAP_HOST_EVENTS 0x34 /* 64 bits */
+/* Battery values are all 32 bits, unless otherwise noted. */
#define EC_MEMMAP_BATT_VOLT 0x40 /* Battery Present Voltage */
#define EC_MEMMAP_BATT_RATE 0x44 /* Battery Present Rate */
#define EC_MEMMAP_BATT_CAP 0x48 /* Battery Remaining Capacity */
-#define EC_MEMMAP_BATT_FLAG 0x4c /* Battery State, defined below */
+#define EC_MEMMAP_BATT_FLAG 0x4c /* Battery State, see below (8-bit) */
+#define EC_MEMMAP_BATT_COUNT 0x4d /* Battery Count (8-bit) */
+#define EC_MEMMAP_BATT_INDEX 0x4e /* Current Battery Data Index (8-bit) */
+/* Unused 0x4f */
#define EC_MEMMAP_BATT_DCAP 0x50 /* Battery Design Capacity */
#define EC_MEMMAP_BATT_DVLT 0x54 /* Battery Design Voltage */
#define EC_MEMMAP_BATT_LFCC 0x58 /* Battery Last Full Charge Capacity */
@@ -103,10 +105,19 @@
/* Unused 0x84 - 0x8f */
#define EC_MEMMAP_ACC_STATUS 0x90 /* Accelerometer status (8 bits )*/
/* Unused 0x91 */
-#define EC_MEMMAP_ACC_DATA 0x92 /* Accelerometer data 0x92 - 0x9f */
+#define EC_MEMMAP_ACC_DATA 0x92 /* Accelerometers data 0x92 - 0x9f */
+/* 0x92: Lid Angle if available, LID_ANGLE_UNRELIABLE otherwise */
+/* 0x94 - 0x99: 1st Accelerometer */
+/* 0x9a - 0x9f: 2nd Accelerometer */
#define EC_MEMMAP_GYRO_DATA 0xa0 /* Gyroscope data 0xa0 - 0xa5 */
-/* Unused 0xa6 - 0xfe (remember, 0xff is NOT part of the memmap region) */
+/* Unused 0xa6 - 0xdf */
+/*
+ * ACPI is unable to access memory mapped data at or above this offset due to
+ * limitations of the ACPI protocol. Do not place data in the range 0xe0 - 0xfe
+ * which might be needed by ACPI.
+ */
+#define EC_MEMMAP_NO_ACPI 0xe0
/* Define the format of the accelerometer mapped memory status byte. */
#define EC_MEMMAP_ACC_STATUS_SAMPLE_ID_MASK 0x0f
@@ -155,6 +166,8 @@
#define EC_BATT_FLAG_DISCHARGING 0x04
#define EC_BATT_FLAG_CHARGING 0x08
#define EC_BATT_FLAG_LEVEL_CRITICAL 0x10
+/* Set if some of the static/dynamic data is invalid (or outdated). */
+#define EC_BATT_FLAG_INVALID_DATA 0x20
/* Switch flags at EC_MEMMAP_SWITCHES */
#define EC_SWITCH_LID_OPEN 0x01
@@ -180,12 +193,200 @@
#define EC_WIRELESS_SWITCH_WWAN 0x04 /* WWAN power */
#define EC_WIRELESS_SWITCH_WLAN_POWER 0x08 /* WLAN power */
+/*****************************************************************************/
+/*
+ * ACPI commands
+ *
+ * These are valid ONLY on the ACPI command/data port.
+ */
+
+/*
+ * ACPI Read Embedded Controller
+ *
+ * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*).
+ *
+ * Use the following sequence:
+ *
+ * - Write EC_CMD_ACPI_READ to EC_LPC_ADDR_ACPI_CMD
+ * - Wait for EC_LPC_CMDR_PENDING bit to clear
+ * - Write address to EC_LPC_ADDR_ACPI_DATA
+ * - Wait for EC_LPC_CMDR_DATA bit to set
+ * - Read value from EC_LPC_ADDR_ACPI_DATA
+ */
+#define EC_CMD_ACPI_READ 0x0080
+
+/*
+ * ACPI Write Embedded Controller
+ *
+ * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*).
+ *
+ * Use the following sequence:
+ *
+ * - Write EC_CMD_ACPI_WRITE to EC_LPC_ADDR_ACPI_CMD
+ * - Wait for EC_LPC_CMDR_PENDING bit to clear
+ * - Write address to EC_LPC_ADDR_ACPI_DATA
+ * - Wait for EC_LPC_CMDR_PENDING bit to clear
+ * - Write value to EC_LPC_ADDR_ACPI_DATA
+ */
+#define EC_CMD_ACPI_WRITE 0x0081
+
+/*
+ * ACPI Burst Enable Embedded Controller
+ *
+ * This enables burst mode on the EC to allow the host to issue several
+ * commands back-to-back. While in this mode, writes to mapped multi-byte
+ * data are locked out to ensure data consistency.
+ */
+#define EC_CMD_ACPI_BURST_ENABLE 0x0082
+
+/*
+ * ACPI Burst Disable Embedded Controller
+ *
+ * This disables burst mode on the EC and stops preventing EC writes to mapped
+ * multi-byte data.
+ */
+#define EC_CMD_ACPI_BURST_DISABLE 0x0083
+
+/*
+ * ACPI Query Embedded Controller
+ *
+ * This clears the lowest-order bit in the currently pending host events, and
+ * sets the result code to the 1-based index of the bit (event 0x00000001 = 1,
+ * event 0x80000000 = 32), or 0 if no event was pending.
+ */
+#define EC_CMD_ACPI_QUERY_EVENT 0x0084
+
+/* Valid addresses in ACPI memory space, for read/write commands */
+
+/* Memory space version; set to EC_ACPI_MEM_VERSION_CURRENT */
+#define EC_ACPI_MEM_VERSION 0x00
+/*
+ * Test location; writing value here updates test compliment byte to (0xff -
+ * value).
+ */
+#define EC_ACPI_MEM_TEST 0x01
+/* Test compliment; writes here are ignored. */
+#define EC_ACPI_MEM_TEST_COMPLIMENT 0x02
+
+/* Keyboard backlight brightness percent (0 - 100) */
+#define EC_ACPI_MEM_KEYBOARD_BACKLIGHT 0x03
+/* DPTF Target Fan Duty (0-100, 0xff for auto/none) */
+#define EC_ACPI_MEM_FAN_DUTY 0x04
+
+/*
+ * DPTF temp thresholds. Any of the EC's temp sensors can have up to two
+ * independent thresholds attached to them. The current value of the ID
+ * register determines which sensor is affected by the THRESHOLD and COMMIT
+ * registers. The THRESHOLD register uses the same EC_TEMP_SENSOR_OFFSET scheme
+ * as the memory-mapped sensors. The COMMIT register applies those settings.
+ *
+ * The spec does not mandate any way to read back the threshold settings
+ * themselves, but when a threshold is crossed the AP needs a way to determine
+ * which sensor(s) are responsible. Each reading of the ID register clears and
+ * returns one sensor ID that has crossed one of its threshold (in either
+ * direction) since the last read. A value of 0xFF means "no new thresholds
+ * have tripped". Setting or enabling the thresholds for a sensor will clear
+ * the unread event count for that sensor.
+ */
+#define EC_ACPI_MEM_TEMP_ID 0x05
+#define EC_ACPI_MEM_TEMP_THRESHOLD 0x06
+#define EC_ACPI_MEM_TEMP_COMMIT 0x07
+/*
+ * Here are the bits for the COMMIT register:
+ * bit 0 selects the threshold index for the chosen sensor (0/1)
+ * bit 1 enables/disables the selected threshold (0 = off, 1 = on)
+ * Each write to the commit register affects one threshold.
+ */
+#define EC_ACPI_MEM_TEMP_COMMIT_SELECT_MASK BIT(0)
+#define EC_ACPI_MEM_TEMP_COMMIT_ENABLE_MASK BIT(1)
+/*
+ * Example:
+ *
+ * Set the thresholds for sensor 2 to 50 C and 60 C:
+ * write 2 to [0x05] -- select temp sensor 2
+ * write 0x7b to [0x06] -- C_TO_K(50) - EC_TEMP_SENSOR_OFFSET
+ * write 0x2 to [0x07] -- enable threshold 0 with this value
+ * write 0x85 to [0x06] -- C_TO_K(60) - EC_TEMP_SENSOR_OFFSET
+ * write 0x3 to [0x07] -- enable threshold 1 with this value
+ *
+ * Disable the 60 C threshold, leaving the 50 C threshold unchanged:
+ * write 2 to [0x05] -- select temp sensor 2
+ * write 0x1 to [0x07] -- disable threshold 1
+ */
+
+/* DPTF battery charging current limit */
+#define EC_ACPI_MEM_CHARGING_LIMIT 0x08
+
+/* Charging limit is specified in 64 mA steps */
+#define EC_ACPI_MEM_CHARGING_LIMIT_STEP_MA 64
+/* Value to disable DPTF battery charging limit */
+#define EC_ACPI_MEM_CHARGING_LIMIT_DISABLED 0xff
+
+/*
+ * Report device orientation
+ * Bits Definition
+ * 3:1 Device DPTF Profile Number (DDPN)
+ * 0 = Reserved for backward compatibility (indicates no valid
+ * profile number. Host should fall back to using TBMD).
+ * 1..7 = DPTF Profile number to indicate to host which table needs
+ * to be loaded.
+ * 0 Tablet Mode Device Indicator (TBMD)
+ */
+#define EC_ACPI_MEM_DEVICE_ORIENTATION 0x09
+#define EC_ACPI_MEM_TBMD_SHIFT 0
+#define EC_ACPI_MEM_TBMD_MASK 0x1
+#define EC_ACPI_MEM_DDPN_SHIFT 1
+#define EC_ACPI_MEM_DDPN_MASK 0x7
+
+/*
+ * Report device features. Uses the same format as the host command, except:
+ *
+ * bit 0 (EC_FEATURE_LIMITED) changes meaning from "EC code has a limited set
+ * of features", which is of limited interest when the system is already
+ * interpreting ACPI bytecode, to "EC_FEATURES[0-7] is not supported". Since
+ * these are supported, it defaults to 0.
+ * This allows detecting the presence of this field since older versions of
+ * the EC codebase would simply return 0xff to that unknown address. Check
+ * FEATURES0 != 0xff (or FEATURES0[0] == 0) to make sure that the other bits
+ * are valid.
+ */
+#define EC_ACPI_MEM_DEVICE_FEATURES0 0x0a
+#define EC_ACPI_MEM_DEVICE_FEATURES1 0x0b
+#define EC_ACPI_MEM_DEVICE_FEATURES2 0x0c
+#define EC_ACPI_MEM_DEVICE_FEATURES3 0x0d
+#define EC_ACPI_MEM_DEVICE_FEATURES4 0x0e
+#define EC_ACPI_MEM_DEVICE_FEATURES5 0x0f
+#define EC_ACPI_MEM_DEVICE_FEATURES6 0x10
+#define EC_ACPI_MEM_DEVICE_FEATURES7 0x11
+
+#define EC_ACPI_MEM_BATTERY_INDEX 0x12
+
+/*
+ * USB Port Power. Each bit indicates whether the corresponding USB ports' power
+ * is enabled (1) or disabled (0).
+ * bit 0 USB port ID 0
+ * ...
+ * bit 7 USB port ID 7
+ */
+#define EC_ACPI_MEM_USB_PORT_POWER 0x13
+
+/*
+ * ACPI addresses 0x20 - 0xff map to EC_MEMMAP offset 0x00 - 0xdf. This data
+ * is read-only from the AP. Added in EC_ACPI_MEM_VERSION 2.
+ */
+#define EC_ACPI_MEM_MAPPED_BEGIN 0x20
+#define EC_ACPI_MEM_MAPPED_SIZE 0xe0
+
+/* Current version of ACPI memory address space */
+#define EC_ACPI_MEM_VERSION_CURRENT 2
+
+
/*
* This header file is used in coreboot both in C and ACPI code. The ACPI code
* is pre-processed to handle constants but the ASL compiler is unable to
* handle actual C code so keep it separate.
*/
-#ifndef __ACPI__
+
/*
* Attributes for EC request and response packets. Just defining __packed
@@ -238,7 +439,7 @@
#define EC_LPC_STATUS_PROCESSING 0x04
/* Last write to EC was a command, not data */
#define EC_LPC_STATUS_LAST_CMD 0x08
-/* EC is in burst mode. Unsupported by Chrome EC, so this bit is never set */
+/* EC is in burst mode */
#define EC_LPC_STATUS_BURST_MODE 0x10
/* SCI event is pending (requesting SCI query) */
#define EC_LPC_STATUS_SCI_PENDING 0x20
@@ -2323,6 +2524,8 @@ struct ec_response_temp_sensor_get_info {
/*****************************************************************************/
/* Host event commands */
+
+/* Obsolete. New implementation should use EC_CMD_HOST_EVENT instead */
/*
* Host event mask params and response structures, shared by all of the host
* event commands below.
@@ -2348,6 +2551,86 @@ struct ec_response_host_event_mask {
#define EC_CMD_HOST_EVENT_SET_WAKE_MASK 0x008E
#define EC_CMD_HOST_EVENT_CLEAR_B 0x008F
+/*
+ * Unified host event programming interface - Should be used by newer versions
+ * of BIOS/OS to program host events and masks
+ */
+
+struct ec_params_host_event {
+
+ /* Action requested by host - one of enum ec_host_event_action. */
+ uint8_t action;
+
+ /*
+ * Mask type that the host requested the action on - one of
+ * enum ec_host_event_mask_type.
+ */
+ uint8_t mask_type;
+
+ /* Set to 0, ignore on read */
+ uint16_t reserved;
+
+ /* Value to be used in case of set operations. */
+ uint64_t value;
+} __ec_align4;
+
+/*
+ * Response structure returned by EC_CMD_HOST_EVENT.
+ * Update the value on a GET request. Set to 0 on GET/CLEAR
+ */
+
+struct ec_response_host_event {
+
+ /* Mask value in case of get operation */
+ uint64_t value;
+} __ec_align4;
+
+enum ec_host_event_action {
+ /*
+ * params.value is ignored. Value of mask_type populated
+ * in response.value
+ */
+ EC_HOST_EVENT_GET,
+
+ /* Bits in params.value are set */
+ EC_HOST_EVENT_SET,
+
+ /* Bits in params.value are cleared */
+ EC_HOST_EVENT_CLEAR,
+};
+
+enum ec_host_event_mask_type {
+
+ /* Main host event copy */
+ EC_HOST_EVENT_MAIN,
+
+ /* Copy B of host events */
+ EC_HOST_EVENT_B,
+
+ /* SCI Mask */
+ EC_HOST_EVENT_SCI_MASK,
+
+ /* SMI Mask */
+ EC_HOST_EVENT_SMI_MASK,
+
+ /* Mask of events that should be always reported in hostevents */
+ EC_HOST_EVENT_ALWAYS_REPORT_MASK,
+
+ /* Active wake mask */
+ EC_HOST_EVENT_ACTIVE_WAKE_MASK,
+
+ /* Lazy wake mask for S0ix */
+ EC_HOST_EVENT_LAZY_WAKE_MASK_S0IX,
+
+ /* Lazy wake mask for S3 */
+ EC_HOST_EVENT_LAZY_WAKE_MASK_S3,
+
+ /* Lazy wake mask for S5 */
+ EC_HOST_EVENT_LAZY_WAKE_MASK_S5,
+};
+
+#define EC_CMD_HOST_EVENT 0x00A4
+
/*****************************************************************************/
/* Switch commands */
@@ -3056,122 +3339,6 @@ struct ec_params_reboot_ec {
*/
#define EC_CMD_GET_PANIC_INFO 0x00D3
-/*****************************************************************************/
-/*
- * ACPI commands
- *
- * These are valid ONLY on the ACPI command/data port.
- */
-
-/*
- * ACPI Read Embedded Controller
- *
- * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*).
- *
- * Use the following sequence:
- *
- * - Write EC_CMD_ACPI_READ to EC_LPC_ADDR_ACPI_CMD
- * - Wait for EC_LPC_CMDR_PENDING bit to clear
- * - Write address to EC_LPC_ADDR_ACPI_DATA
- * - Wait for EC_LPC_CMDR_DATA bit to set
- * - Read value from EC_LPC_ADDR_ACPI_DATA
- */
-#define EC_CMD_ACPI_READ 0x80
-
-/*
- * ACPI Write Embedded Controller
- *
- * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*).
- *
- * Use the following sequence:
- *
- * - Write EC_CMD_ACPI_WRITE to EC_LPC_ADDR_ACPI_CMD
- * - Wait for EC_LPC_CMDR_PENDING bit to clear
- * - Write address to EC_LPC_ADDR_ACPI_DATA
- * - Wait for EC_LPC_CMDR_PENDING bit to clear
- * - Write value to EC_LPC_ADDR_ACPI_DATA
- */
-#define EC_CMD_ACPI_WRITE 0x81
-
-/*
- * ACPI Query Embedded Controller
- *
- * This clears the lowest-order bit in the currently pending host events, and
- * sets the result code to the 1-based index of the bit (event 0x00000001 = 1,
- * event 0x80000000 = 32), or 0 if no event was pending.
- */
-#define EC_CMD_ACPI_QUERY_EVENT 0x84
-
-/* Valid addresses in ACPI memory space, for read/write commands */
-
-/* Memory space version; set to EC_ACPI_MEM_VERSION_CURRENT */
-#define EC_ACPI_MEM_VERSION 0x00
-/*
- * Test location; writing value here updates test compliment byte to (0xff -
- * value).
- */
-#define EC_ACPI_MEM_TEST 0x01
-/* Test compliment; writes here are ignored. */
-#define EC_ACPI_MEM_TEST_COMPLIMENT 0x02
-
-/* Keyboard backlight brightness percent (0 - 100) */
-#define EC_ACPI_MEM_KEYBOARD_BACKLIGHT 0x03
-/* DPTF Target Fan Duty (0-100, 0xff for auto/none) */
-#define EC_ACPI_MEM_FAN_DUTY 0x04
-
-/*
- * DPTF temp thresholds. Any of the EC's temp sensors can have up to two
- * independent thresholds attached to them. The current value of the ID
- * register determines which sensor is affected by the THRESHOLD and COMMIT
- * registers. The THRESHOLD register uses the same EC_TEMP_SENSOR_OFFSET scheme
- * as the memory-mapped sensors. The COMMIT register applies those settings.
- *
- * The spec does not mandate any way to read back the threshold settings
- * themselves, but when a threshold is crossed the AP needs a way to determine
- * which sensor(s) are responsible. Each reading of the ID register clears and
- * returns one sensor ID that has crossed one of its threshold (in either
- * direction) since the last read. A value of 0xFF means "no new thresholds
- * have tripped". Setting or enabling the thresholds for a sensor will clear
- * the unread event count for that sensor.
- */
-#define EC_ACPI_MEM_TEMP_ID 0x05
-#define EC_ACPI_MEM_TEMP_THRESHOLD 0x06
-#define EC_ACPI_MEM_TEMP_COMMIT 0x07
-/*
- * Here are the bits for the COMMIT register:
- * bit 0 selects the threshold index for the chosen sensor (0/1)
- * bit 1 enables/disables the selected threshold (0 = off, 1 = on)
- * Each write to the commit register affects one threshold.
- */
-#define EC_ACPI_MEM_TEMP_COMMIT_SELECT_MASK (1 << 0)
-#define EC_ACPI_MEM_TEMP_COMMIT_ENABLE_MASK (1 << 1)
-/*
- * Example:
- *
- * Set the thresholds for sensor 2 to 50 C and 60 C:
- * write 2 to [0x05] -- select temp sensor 2
- * write 0x7b to [0x06] -- C_TO_K(50) - EC_TEMP_SENSOR_OFFSET
- * write 0x2 to [0x07] -- enable threshold 0 with this value
- * write 0x85 to [0x06] -- C_TO_K(60) - EC_TEMP_SENSOR_OFFSET
- * write 0x3 to [0x07] -- enable threshold 1 with this value
- *
- * Disable the 60 C threshold, leaving the 50 C threshold unchanged:
- * write 2 to [0x05] -- select temp sensor 2
- * write 0x1 to [0x07] -- disable threshold 1
- */
-
-/* DPTF battery charging current limit */
-#define EC_ACPI_MEM_CHARGING_LIMIT 0x08
-
-/* Charging limit is specified in 64 mA steps */
-#define EC_ACPI_MEM_CHARGING_LIMIT_STEP_MA 64
-/* Value to disable DPTF battery charging limit */
-#define EC_ACPI_MEM_CHARGING_LIMIT_DISABLED 0xff
-
-/* Current version of ACPI memory address space */
-#define EC_ACPI_MEM_VERSION_CURRENT 1
-
-
/*****************************************************************************/
/*
* HDMI CEC commands
@@ -3285,8 +3452,6 @@ enum mkbp_cec_event {
*/
#define EC_CMD_VERSION0 0x00DC
-#endif /* !__ACPI__ */
-
/*****************************************************************************/
/*
* PD commands
@@ -3627,4 +3792,6 @@ struct ec_response_usb_pd_mux_info {
#define EC_LPC_ADDR_OLD_PARAM EC_HOST_CMD_REGION1
#define EC_OLD_PARAM_SIZE EC_HOST_CMD_REGION_SIZE
+
+
#endif /* __CROS_EC_COMMANDS_H */
--
2.21.0.1020.gf2820cf01a-goog
