Re: [PATCH 1/3] iio: Add driver for Infineon DPS310

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 5/6/19 4:18 PM, Peter Meerwald-Stadler wrote:
On Mon, 6 May 2019, Eddie James wrote:

From: Joel Stanley <joel@xxxxxxxxx>
some comments below


Thanks for the quick review! Will get these in for v2, I did have a couple of questions below though.

Eddie


The DPS310 is a temperature and pressure sensor. It can be accessed over
i2c and SPI.

Signed-off-by: Eddie James <eajames@xxxxxxxxxxxxx>
---
  MAINTAINERS                   |   6 +
  drivers/iio/pressure/Kconfig  |  10 +
  drivers/iio/pressure/Makefile |   1 +
  drivers/iio/pressure/dps310.c | 429 ++++++++++++++++++++++++++++++++++++++++++
  4 files changed, 446 insertions(+)
  create mode 100644 drivers/iio/pressure/dps310.c

diff --git a/MAINTAINERS b/MAINTAINERS
index c61c49d..a91dfa9 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7743,6 +7743,12 @@ W:	http://industrypack.sourceforge.net
  S:	Maintained
  F:	drivers/ipack/
+INFINEON DPS310 Driver
+M:	Eddie James <eajames@xxxxxxxxxxxxx>
+L:	linux-iio@xxxxxxxxxxxxxxx
+F:	drivers/iio/pressure/dps310.c
+S:	Maintained
+
  INFINIBAND SUBSYSTEM
  M:	Doug Ledford <dledford@xxxxxxxxxx>
  M:	Jason Gunthorpe <jgg@xxxxxxxxxxxx>
diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig
index efeb89f..681a1cc 100644
--- a/drivers/iio/pressure/Kconfig
+++ b/drivers/iio/pressure/Kconfig
@@ -52,6 +52,16 @@ config IIO_CROS_EC_BARO
  	  To compile this driver as a module, choose M here: the module
  	  will be called cros_ec_baro.
+config DPS310
+       tristate "Infineon DPS310 pressure and temperature sensor"
+       depends on I2C
+       select REGMAP_I2C
+       help
+	 Support for the Infineon DPS310 digital barometric pressure sensor.
+
+	 This driver can also be built as a module.  If so, the module will be
+	 called dps310.
+
  config HID_SENSOR_PRESS
  	depends on HID_SENSOR_HUB
  	select IIO_BUFFER
diff --git a/drivers/iio/pressure/Makefile b/drivers/iio/pressure/Makefile
index c2058d7..d8f5ace 100644
--- a/drivers/iio/pressure/Makefile
+++ b/drivers/iio/pressure/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_BMP280) += bmp280.o
  bmp280-objs := bmp280-core.o bmp280-regmap.o
  obj-$(CONFIG_BMP280_I2C) += bmp280-i2c.o
  obj-$(CONFIG_BMP280_SPI) += bmp280-spi.o
+obj-$(CONFIG_DPS310) += dps310.o
  obj-$(CONFIG_IIO_CROS_EC_BARO) += cros_ec_baro.o
  obj-$(CONFIG_HID_SENSOR_PRESS)   += hid-sensor-press.o
  obj-$(CONFIG_HP03) += hp03.o
diff --git a/drivers/iio/pressure/dps310.c b/drivers/iio/pressure/dps310.c
new file mode 100644
index 0000000..21d5dcb
--- /dev/null
+++ b/drivers/iio/pressure/dps310.c
@@ -0,0 +1,429 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright IBM Corp 2019
+/*
+ * The DPS310 is a barometric pressure and temperature sensor.
+ * Currently only reading a single temperature is supported by
+ * this driver.
+ *
+ * https://www.infineon.com/dgdl/?fileId=5546d462576f34750157750826c42242
+ *
+ * Temperature calculation:
+ *   c0 * 0.5 + c1 * T_raw / kT °C
+ *
+ * TODO:
+ *  - Pressure sensor readings
+ *  - Optionally support the FIFO
+ */
+
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+
+#define DPS310_PRS_B0		0x00
+#define DPS310_PRS_B1		0x01
+#define DPS310_PRS_B2		0x02
+#define DPS310_TMP_B0		0x03
+#define DPS310_TMP_B1		0x04
+#define DPS310_TMP_B2		0x05
+#define DPS310_PRS_CFG		0x06
+#define DPS310_TMP_CFG		0x07
+#define  DPS310_TMP_RATE_BITS	GENMASK(6, 4)
+#define  DPS310_TMP_PRC_BITS	GENMASK(3, 0)
+#define  DPS310_TMP_EXT		BIT(7)
+#define DPS310_MEAS_CFG		0x08
+#define  DPS310_MEAS_CTRL_BITS	GENMASK(2, 0)
+#define   DPS310_PRS_EN		BIT(0)
+#define   DPS310_TEMP_EN	BIT(1)
+#define   DPS310_BACKGROUND	BIT(2)
+#define  DPS310_PRS_RDY		BIT(4)
+#define  DPS310_TMP_RDY		BIT(5)
+#define  DPS310_SENSOR_RDY	BIT(6)
+#define  DPS310_COEF_RDY	BIT(7)
+#define DPS310_CFG_REG		0x09
+#define  DPS310_INT_HL		BIT(7)
+#define  DPS310_TMP_SHIFT_EN	BIT(3)
+#define  DPS310_PRS_SHIFT_EN	BIT(4)
+#define  DPS310_FIFO_EN		BIT(5)
+#define  DPS310_SPI_EN		BIT(6)
+#define DPS310_RESET		0x0c
+#define  DPS310_RESET_MAGIC	(BIT(0) | BIT(3))
+#define DPS310_COEF_BASE	0x10
+
+#define DPS310_PRS_BASE		DPS310_PRS_B0
+#define DPS310_TMP_BASE		DPS310_TMP_B0
+
+#define DPS310_CALC_RATE(_n)	ilog2(_n)
+#define DPS310_CALC_PRC(_n)	ilog2(_n)
+
+const int scale_factor[] = {
static
maybe plural, scale_factors?
maybe some comment would be good what these values relate to

+	 524288,
+	1572864,
+	3670016,
+	7864320,
+	 253952,
+	 516096,
+	1040384,
+	2088960,
+};
+
+struct dps310_data {
+	struct i2c_client *client;
+	struct regmap *regmap;
+
+	s32 c0, c1;
+	s32 temp_raw;
+};
+
+static const struct iio_chan_spec dps310_channels[] = {
+	{
+		.type = IIO_TEMP,
+		.info_mask_separate = BIT(IIO_CHAN_INFO_OFFSET) |
+			BIT(IIO_CHAN_INFO_SCALE) |
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO) |
+			BIT(IIO_CHAN_INFO_SAMP_FREQ) |
+			BIT(IIO_CHAN_INFO_RAW),
+	},
+};
+
+/* To be called after checking the TMP_RDY bit in MEAS_CFG */
+static int dps310_get_temp_coef(struct dps310_data *data)
+{
+	struct regmap *regmap = data->regmap;
+	u8 coef[3] = {0};
initialization needed?

+	int r;
+	u32 c0, c1;
+
+	/*
+	 * Read temperature calibration coefficients c0 and c1 from the
+	 * COEF register. The numbers are 12-bit 2's compliment numbers
+	 */
+	r = regmap_bulk_read(regmap, DPS310_COEF_BASE, coef, 3);
sizeof(coef) instead of 3

+	if (r < 0)
+		return r;
+
+	c0 = (coef[0] << 4) | (coef[1] >> 4);
+	data->c0 = sign_extend32(c0, 11);
+
+	c1 = ((coef[1] & GENMASK(3, 0)) << 8) | coef[2];
+	data->c1 = sign_extend32(c1, 11);
+
+	return 0;
+}
+
+static int dps310_get_temp_precision(struct dps310_data *data)
+{
+	int val, r;
+
+	r = regmap_read(data->regmap, DPS310_TMP_CFG, &val);
+	if (r < 0)
+		return r;
+
+	/*
+	 * Scale factor is bottom 4 bits of the register, but 1111 is
+	 * reserved so just grab bottom three
+	 */
+	return BIT(val & GENMASK(2, 0));
+}
+
+static int dps310_set_temp_precision(struct dps310_data *data, int val)
+{
+	int ret;
+	u8 shift_en;
+
+	if (val < 0 || val > 128)
+		return -EINVAL;
+
+	shift_en = val >= 16 ? DPS310_TMP_SHIFT_EN : 0;
+	ret = regmap_write_bits(data->regmap, DPS310_CFG_REG,
+				DPS310_TMP_SHIFT_EN, shift_en);
+	if (ret)
+		return ret;
+
+	return regmap_update_bits(data->regmap, DPS310_TMP_CFG,
+				  DPS310_TMP_PRC_BITS, DPS310_CALC_PRC(val));
+}
+
+static int dps310_set_temp_samp_freq(struct dps310_data *data, int freq)
+{
+	u8 val;
+
+	if (freq < 0 || freq > 128)
+		return -EINVAL;
+
+	val = DPS310_CALC_RATE(freq) << 4;
+
+	return regmap_update_bits(data->regmap, DPS310_TMP_CFG,
+				  DPS310_TMP_RATE_BITS, val);
+}
+
+static int dps310_get_temp_samp_freq(struct dps310_data *data)
+{
+	int val, r;
+
+	r = regmap_read(data->regmap, DPS310_TMP_CFG, &val);
+	if (r < 0)
+		return r;
+
+	return BIT((val & DPS310_TMP_RATE_BITS) >> 4);
+}
+
+static int dps310_get_temp_k(struct dps310_data *data)
+{
+	int r = dps310_get_temp_precision(data);
+
+	if (r < 0)
+		return r;
+
+	return scale_factor[DPS310_CALC_PRC(r)];
+}
+
+static int dps310_read_temp(struct dps310_data *data)
+{
+	struct device *dev = &data->client->dev;
+	struct regmap *regmap = data->regmap;
+	u8 val[3] = {0};
initialization needed?

+	int r, ready;
+	int T_raw;
+
+	r = regmap_read(regmap, DPS310_MEAS_CFG, &ready);
+	if (r < 0)
+		return r;
+	if (!(ready & DPS310_TMP_RDY)) {
+		dev_dbg(dev, "temperature not ready\n");
most drivers wait for the results to become ready\


OK, this may have to wait up to a second then, since the background measurement rate can be as low as 1 HZ... I can base the timeout on the sample rate. Would that be OK?



+		return -EAGAIN;
+	}
+
+	r = regmap_bulk_read(regmap, DPS310_TMP_BASE, val, 3);
sizeof(val)

+	if (r < 0)
+		return r;
+
+	T_raw = (val[0] << 16) | (val[1] << 8) | val[2];
+	data->temp_raw = sign_extend32(T_raw, 23);
+
+	return 0;
+}
+
+static bool dps310_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case DPS310_PRS_CFG:
+	case DPS310_TMP_CFG:
+	case DPS310_MEAS_CFG:
+	case DPS310_CFG_REG:
+	case DPS310_RESET:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool dps310_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case DPS310_PRS_B0:
+	case DPS310_PRS_B1:
+	case DPS310_PRS_B2:
+	case DPS310_TMP_B0:
+	case DPS310_TMP_B1:
+	case DPS310_TMP_B2:
+	case DPS310_MEAS_CFG:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static int dps310_write_raw(struct iio_dev *iio,
+			    struct iio_chan_spec const *chan, int val,
+			    int val2, long mask)
+{
+	struct dps310_data *data = iio_priv(iio);
+
+	if (chan->type != IIO_TEMP)
+		return -EINVAL;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		return dps310_set_temp_samp_freq(data, val);
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		return dps310_set_temp_precision(data, val);
+	default:
+		return -EINVAL;
+	}
+
+	return -EINVAL;
not needed, dead code

+}
+
+static int dps310_read_raw(struct iio_dev *iio,
+			   struct iio_chan_spec const *chan,
+			   int *val, int *val2, long mask)
+{
+	struct dps310_data *data = iio_priv(iio);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*val = dps310_get_temp_samp_freq(data);
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_RAW:
+		ret = dps310_read_temp(data);
+		if (ret)
+			return ret;
+
+		*val = data->temp_raw * data->c1;
one could try to avoid the multipliation here and somehow mangle it into
_SCALE/_OFFSET


Don't think it's worth it? Would have to divide the offset by c1 and then multiply by c1 again in the scale...



+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_OFFSET:
+		ret = dps310_get_temp_k(data);
+		if (ret < 0)
+			return ret;
+
+		*val = (data->c0 >> 1) * ret;
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_SCALE:
+		ret = dps310_get_temp_k(data);
+		if (ret < 0)
+			return ret;
+
+		*val = 1000; /* milliCelsius per Celsius */
+		*val2 = ret;
+		return IIO_VAL_FRACTIONAL;
+
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		*val = dps310_get_temp_precision(data);
+		return IIO_VAL_INT;
+
+	default:
+		return -EINVAL;
+	}
+
+	return -EINVAL;
not needed, dead code

+}
+
+static const struct regmap_config dps310_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.writeable_reg = dps310_is_writeable_reg,
+	.volatile_reg = dps310_is_volatile_reg,
+	.cache_type = REGCACHE_RBTREE,
+	.max_register = 0x29,
+};
+
+static const struct iio_info dps310_info = {
+	.read_raw = dps310_read_raw,
+	.write_raw = dps310_write_raw,
+};
+
+static int dps310_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct dps310_data *data;
+	struct iio_dev *iio;
+	int r, ready;
+
+	iio = devm_iio_device_alloc(&client->dev,  sizeof(*data));
+	if (!iio)
+		return -ENOMEM;
+
+	data = iio_priv(iio);
+	data->client = client;
+
+	iio->dev.parent = &client->dev;
+	iio->name = id->name;
+	iio->channels = dps310_channels;
+	iio->num_channels = ARRAY_SIZE(dps310_channels);
+	iio->info = &dps310_info;
+	iio->modes = INDIO_DIRECT_MODE;
+
+	data->regmap = devm_regmap_init_i2c(client, &dps310_regmap_config);
+	if (IS_ERR(data->regmap))
+		return PTR_ERR(data->regmap);
+
+	/*
+	 * Set up external (MEMS) temperature sensor in single sample, one
+	 * measurement per second mode
+	 */
+	r = regmap_write(data->regmap, DPS310_TMP_CFG,
+			 DPS310_TMP_EXT | DPS310_CALC_RATE(1) |
+			 DPS310_CALC_PRC(1));
+	if (r < 0)
+		goto err;
+
+	/* Temp shift is disabled when PRC <= 8 */
+	r = regmap_write_bits(data->regmap, DPS310_CFG_REG,
+			      DPS310_TMP_SHIFT_EN, 0);
+	if (r < 0)
+		goto err;
+
+	/* Turn on temperature measurement in the background */
+	r = regmap_write_bits(data->regmap, DPS310_MEAS_CFG,
+			      DPS310_MEAS_CTRL_BITS,
+			      DPS310_TEMP_EN | DPS310_BACKGROUND);
+	if (r < 0)
+		goto err;
+
+	/*
+	 * Calibration coefficients required for reporting temperature.
+	 * They are available 40ms after the device has started
+	 */
+	r = regmap_read_poll_timeout(data->regmap, DPS310_MEAS_CFG, ready,
+				     ready & DPS310_COEF_RDY, 10000, 40000);
+	if (r < 0)
+		goto err;
+
+	r = dps310_get_temp_coef(data);
+	if (r < 0)
+		goto err;
+
+	r = devm_iio_device_register(&client->dev, iio);
+	if (r)
+		goto err;
+
+	i2c_set_clientdata(client, iio);
+
+	dev_info(&client->dev, "%s: sensor '%s'\n", dev_name(&iio->dev),
+		 client->name);
don't clutter the log

+
+	return 0;
+
+err:
+	regmap_write(data->regmap, DPS310_RESET, DPS310_RESET_MAGIC);
+	return r;
+}
+
+static int dps310_remove(struct i2c_client *client)
+{
+	struct dps310_data *data = i2c_get_clientdata(client);
+
+	return regmap_write(data->regmap, DPS310_RESET, DPS310_RESET_MAGIC);
+}
+
+static const struct i2c_device_id dps310_id[] = {
+	{ "dps310", 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, dps310_id);
+
+static const unsigned short normal_i2c[] = {
+	0x77, 0x76, I2C_CLIENT_END
+};
+
+static struct i2c_driver dps310_driver = {
+	.driver = {
+		.name = "dps310",
+	},
+	.probe = dps310_probe,
+	.remove = dps310_remove,
+	.address_list = normal_i2c,
+	.id_table = dps310_id,
+};
+module_i2c_driver(dps310_driver);
+
+MODULE_AUTHOR("Joel Stanley <joel@xxxxxxxxx>");
+MODULE_DESCRIPTION("Infineon DPS310 pressure and temperature sensor");
+MODULE_LICENSE("GPL v2");





[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux