Re: [PATCH 3/3] iio: Add PAT9125 optical tracker sensor

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello Jonathan,

On 4/7/19 12:20, Jonathan Cameron wrote:
Hi Alexandre,

So I have no problem with this as an IIO driver, but for devices that
are somewhat 'on the edge' I always like to get a clear answer to the
question: Why not input?

I would also argue that, to actually be 'useful' we would typically need
some representation of the 'mechanicals' that are providing the motion
being measured.  Looking at the datasheet this includes, rotating shafts
(side or end on), disk edges and flat surface tracking (mouse like).

That's easy enough to do with the iio in kernel consumer interface. These
are similar to when we handle analog electronic front ends.

I you can, please describe what it is being used for in your application
as that may give us somewhere to start!

+ CC Dmitry and linux-input.

I developed this driver to detect the board movement which can't be detected by accelerometer (very slow motion). I admit this use case can be handled by an input, and I'm agree with you, PAT9125 driver could be an input. But, like you said, this chip is able to track different kind of motion, and additionally have an interrupt GPIO, so using it like input limit the driver potential. This chip is designed to work in industrial measurement or embedded systems, and the IIO API match with these environments, so it's the best way to exploit the entire potential of this chip.

As I understand (from https://www.kernel.org/doc/html/v4.12/input/event-codes.html#mice ), mouse driver must report values when the device move. This feature souldn't be mandatory for an optical tracker driver, specially for cases where user prefers to use buffer or poll only when he need data.

If 1 or 2, I would suggest that you provide absolute position to
Linux.  So add the value to a software counter and provide that.
32 bits should be plenty of resolution for that.
I can't provide absolute position, only relative. Do you mean using input driver to do that ? If not, how is built the position data?

Silly question for you.  What happens if you set the delta values to 0?
Do we get an interrupt which is effectively data ready?
If we do, you might want to think about a scheme where that is an option.
As things currently stand we have a confusing interface where changing this
threshold effects the buffered data output.   That should only be the
case if this interface is for a trigger, not an event.

I'm not sure to understand your question. Is it possible to read delta_x and delta_y = 0 in special/corner case because internal value continue to be updated after toggled motion_detect pin (used for IRQ) until values registers are read and then motion_detect pin is released:

 * Chip move (i.e. +2 on X axis and 0 on Y axis)
 * Motion_detect IRQ trigger and internal reg value is updated (i.e.
   delta_x = 2 and delta_y = 0)
 * GPIO IRQ handled but read_value isn't executed yet (timing reason)
 * Chip move back to it origin point (i.e. -2 on X axis and 0 on Y axis)
 * Motion_detect IRQ still low because it hasn't been reset by read
   value and internal reg value is updated (i.e. delta_x = 0 and
   delta_y = 0)
 * Read_value is executed, we get delta values = 0.

If it is actually not possible to report the two channels separately
then don't report them at all except via the buffered interface and
set the available scan masks so that both are on.
I found a way to keep the consistency between delta x and delta y (without losing data). The first part is to reset a value only when user read it (also when it's buffered). The second part is to add the new value to the old value. With these two mechanism, X and Y will always be consistent:

 * as possible during a move.
 * perfectly when move is finished.


Regards,

Alexandre




[Index of Archives]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Input]     [Linux Kernel]     [Linux SCSI]     [X.org]

  Powered by Linux