On Thu, 2018-10-18 at 12:12 +0300, Stefan Popa wrote:
> Document support for AD7606 Analog to Digital Converter.
>
Commments inline
> Signed-off-by: Stefan Popa <stefan.popa@xxxxxxxxxx>
> ---
> .../devicetree/bindings/iio/adc/adi,ad7606.txt | 51
> ++++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 52 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> new file mode 100644
> index 0000000..dede581
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> @@ -0,0 +1,51 @@
> +Analog Devices AD7606 Simultaneous Sampling ADC
> +
> +Required properties for the AD7606:
> +
> + - compatible: Must be one of "adi,ad7605-4", "adi,ad7606-8",
> "adi,ad7606-6" or
> + "adi,ad7606-4".
> + - reg: SPI chip select number for the device
> + - spi-max-frequency: Max SPI frequency to use
> + see: Documentation/devicetree/bindings/spi/spi-bus.txt
> + - spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
I don't know what the typical preference is (with respect to SPI docs), but
I'd just reference the "Documentation/devicetree/bindings/spi/spi-bus.txt
"doc here.
> + - avcc-supply: phandle to the Avcc power supply
> + - interrupts: IRQ line for the ADC
> + see: Documentation/devicetree/bindings/interrupt-
> controller/interrupts.txt
> + - conversion-start-gpio: must be the device tree identifier of the
> CONVST pin.
> + This logic input is used to initiate conversions
> on
> + the analog input channels.
> +
> +Optional properties:
> +
> + - reset-gpio: must be the device tree identifier of the RESET pin. If
> specified,
> + it will be asserted during driver probe.
> + - first-data-gpio: must be the device tree identifier of the FRSTDATA
> pin.
> + The FRSTDATA output indicates when the first channel,
> V1, is
> + being read back on either the parallel, byte or serial
> interface.
> +- standby-gpio: must be the device tree identifier of the STBY pin. This
> pin is used
> + to place the AD7606 into one of two power-down modes,
> Standby mode or
> + Shutdown mode.
> +- range-gpio: must be the device tree identifier of the RANGE pin. The
> polarity on
> + this pin determines the input range of the analog input
> channels. If
> + this pin is tied to a logic high, the analog input range is
> ±10V for
> + allchannels. If this pin is tied to a logic low, the analog
> input range
> + is ±5V for all channels.
> +
nitpick: `range-gpio` && `standby-gpio` entries are indented differently
than `reset-gpio` && `first-data-gpio`
> +Example:
> +
> + adc@0 {
> + compatible = "adi,ad7606-8";
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + spi-cpol;
> +
> + avcc-supply = <&adc_vref>;
> +
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-parent = <&gpio>;
> +
> + conversion-start-gpio = <&gpio 17 0>;
> + reset-gpio = <&gpio 27 0>;
> + first-data-gpio = <&gpio 22 0>;
> + standby-gpio = <&gpio 24 0>;
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 843545d..6d63db4 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -845,6 +845,7 @@ L: linux-iio@xxxxxxxxxxxxxxx
> W: http://ez.analog.com/community/linux-device-drivers
> S: Supported
> F: drivers/iio/adc/ad7606.c
> +F: Documentation/devicetree/bindings/iio/adc/ad7606.txt
>
> ANALOG DEVICES INC AD9389B DRIVER
> M: Hans Verkuil <hans.verkuil@xxxxxxxxx>
