On Tue, 9 Jan 2018 10:33:31 +0100 Quentin Schulz <quentin.schulz@xxxxxxxxxxxxxxxxxx> wrote: > The AXP813 PMIC is relatively close to the already supported AXP20X and > AXP22X. It provides three different power outputs: battery, AC and USB, and > measures a few different things: temperature, power supply status, current > current and voltage supplied, maximum current limit, battery capacity, min > and max voltage limits. > > One of its two GPIOs can be used as an ADC. > > There are a few differences with AXP20X/AXP22X PMICs though: > - a different constant charge current formula, > - battery temperature, GPIO0 and battery voltages are the only voltages > measurable, > - all data are stored on 12 bits (AXP20X/AXP22X had one type of data that > was stored on 13 bits), > - different scales and offsets, > - a different ADC rate formula and register, > > This patch series adds support for the PMIC's ADC and battery power supply > in the existing drivers. > > Make the axp20x MFD automatically probe the ADC driver, add the battery > power supply node in axp81x node and enable it for the TBS A711 since it > has a soldered battery. > > v2: > - introduce data structure instead of ID for variant specific code in > battery driver, > - add DT binding for ADC driver, > - make mfd probe the ADC driver via DT as well so that its IIO channels > can be consumed by other drivers via DT mapping, Other than that minor comment on V1 about churn risk in the dt binding that Rob pointed out hadn't been addressed (I'd completely forgotten about it :) I'm happy once the points others have raised have been addressed. My assumption is that this will ultimately go through the IIO tree so I'll be needing a good selection of Acks to take it. The dts bits should be fine to go via normal paths though once the driver is in place. If it's going via mfd which might make sense in a 'logical' way rather than amount of code, let me know and I'll give tags for v3 iio parts. Jonathan > > Thanks, > Quentin > > Quentin Schulz (16): > iio: adc: axp20x_adc: put ADC rate setting in a per-variant function > dt-bindings: iio: adc: add binding for X-Powers AXP PMICs ADC > iio: adc: axp20x_adc: make it possible to probe from DT > ARM: dtsi: axp209: add node for ADC > ARM: dtsi: axp22x: add node for ADC > mfd: axp20x: make AXP209/22x cells probe their ADC via DT > dt-bindings: iio: adc: axp20x_adc: add AXP813 variant > iio: adc: axp20x_adc: add support for AXP813 ADC > ARM: dtsi: axp81x: add node for ADC > mfd: axp20x: probe axp20x_adc driver for AXP813 > power: supply: axp20x_battery: use data structure instead of ID for variant specific code > dt-bindings: power: supply: axp20x: add AXP813 battery DT binding > power: supply: axp20x_battery: add support for AXP813 > mfd: axp20x: add battery power supply cell for AXP813 > ARM: dtsi: axp81x: add battery power supply subnode > ARM: dtsi: sun8i: a711: enable battery power supply subnode > > Documentation/devicetree/bindings/iio/adc/axp20x_adc.txt | 48 ++++++++++++++++++++++- > Documentation/devicetree/bindings/power/supply/axp20x_battery.txt | 8 ++-- > arch/arm/boot/dts/axp209.dtsi | 5 ++- > arch/arm/boot/dts/axp22x.dtsi | 5 ++- > arch/arm/boot/dts/axp81x.dtsi | 10 +++++- > arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts | 4 ++- > drivers/iio/adc/axp20x_adc.c | 160 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++---- > drivers/mfd/axp20x.c | 13 +++++- > drivers/power/supply/axp20x_battery.c | 134 ++++++++++++++++++++++++++++++++++++++++++++++-------------- > include/linux/mfd/axp20x.h | 2 +- > 10 files changed, 345 insertions(+), 44 deletions(-) > create mode 100644 Documentation/devicetree/bindings/iio/adc/axp20x_adc.txt > > base-commit: 895c0dde398510a5b5ded60e5064c11b94bd30ca -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
