* Jonathan Cameron <jic23@xxxxxxxxxx> [170520 08:58]: > On 19/05/17 04:40, Tony Lindgren wrote: > > It seems that "MC13783 Power Management and Audio Ciruit User's Guide" > > MC1378UG.pdf documents several similar components as in the CPCAP PMIC. > > > > Chapter "9.5.5 Die Temperature and UID" says that the die temperature > > value is 282 at 25C with LSB of -1.14C. Converting CPCAP PMIC channel3 > > values with following seems to produce values that make sense for a > > PMIC die: > > > > temperature = 25000 + ((regval - 282) * 114) > > > > As we don't have any other documentation, let's assume the die > > temperature is unconfigured in the Motorola mapphone Linux kernel > > and the current temperature conversion table should be only used > > for the battery thermistor and not for the die temperature. > Is there any route we have available to confirm this? I.e. doe anyone > have one where we can check plausibility? Well there is also a tmp105 sensor for SoC temperature on board that I used for some sanity checks :) For the Motorola kernel, it seems it's doing all the interesting ADC stuff in user space for battery estimates. So if ch3 is used, it must be using the raw values. My guess is that ch3 is only used by the PMIC firmware to automatically cut off power if it gets too hot. The temperature values seem to make sense now when compared against the tmp105 values.. The following output is from an idle device with charger connected with reasonably full battery: $ ./test-d4-temperature tmp105: 37187 bat ch0: 33675 die ch3: 46888 tmp105: 37187 bat ch0: 33820 die ch3: 41074 tmp105: 37187 bat ch0: 33525 die ch3: 40390 tmp105: 37125 bat ch0: 33675 die ch3: 40162 tmp105: 37125 bat ch0: 34410 die ch3: 40048 tmp105: 37125 bat ch0: 34555 die ch3: 40162 tmp105: 37125 bat ch0: 33525 die ch3: 40390 ... Add some load with two instances of dd if=/dev/urandom of=/dev/null: $ ./test-d4-temperature tmp105: 44250 bat ch0: 37240 die ch3: 51790 tmp105: 44250 bat ch0: 34705 die ch3: 48940 tmp105: 44250 bat ch0: 34705 die ch3: 48484 tmp105: 44250 bat ch0: 34850 die ch3: 48370 tmp105: 44312 bat ch0: 37585 die ch3: 48142 tmp105: 44312 bat ch0: 36895 die ch3: 48484 tmp105: 44375 bat ch0: 34705 die ch3: 48484 tmp105: 44375 bat ch0: 36895 die ch3: 48484 ... So ch3 for the PMIC die temperature seems to follow the load numbers and makes sense as it provides power to all the devices. The first value of ch3 often is all over the map though, probably no way around that.. The script I'm using is: #!/bin/sh while [ 1 ]; do echo -n "tmp105: $(cat /sys/class/hwmon/hwmon0/temp1_input) " echo -n "bat ch0: $(cat /sys/bus/iio/devices/iio:device0/in_temp0_input) " echo "die ch3: $(cat /sys/bus/iio/devices/iio:device0/in_temp3_input)" sleep 1 done Regards, Tony -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
