On Tue, May 2, 2017 at 11:02 PM, Jan Kiszka <jan.kiszka@xxxxxxxxxxx> wrote:
> This is an upstream port of an IIO driver for the TI ADC108S102 and
> ADC128S102. The former can be found on the Intel Galileo Gen2 and the
> Siemens SIMATIC IOT2000. For those boards, ACPI-based enumeration is
> included.
>
> Original author: Bogdan Pricop <bogdan.pricop@xxxxxxxxxx>
> Ported from Intel Galileo Gen2 BSP to Intel Yocto kernel:
> Todor Minchev <todor@xxxxxxxxxxxxx>.
There are several nitpicks, and one concern about regulator.
After addressing at least the latter
Reviewed-by: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
> +#include <linux/acpi.h>
> +#include <linux/gpio.h>
Redundant I beleive.
> +static int adc108s102_update_scan_mode(struct iio_dev *indio_dev,
> + unsigned long const *active_scan_mask)
> +{
> + struct adc108s102_state *st;
> + unsigned int bit, cmds;
> +
> + st = iio_priv(indio_dev);
> +
I think it's a quite good pattern to assign such variables above at
definition block.
This also would be done in several functions below (except ->probe() call)
> + /*
> + * Fill in the first x shorts of tx_buf with the number of channels
> + * enabled for sampling by the triggered buffer
> + */
Usually in multiline comments even for one sentence we use period at the end.
> + cmds = 0;
> + for_each_set_bit(bit, active_scan_mask, ADC108S102_MAX_CHANNELS)
> + st->tx_buf[cmds++] = cpu_to_be16(ADC108S102_CMD(bit));
> +
> + /* One dummy command added, to clock in the last response */
> + st->tx_buf[cmds++] = 0x00;
> +
> + /* build SPI ring message */
> + st->ring_xfer.tx_buf = &st->tx_buf[0];
> + st->ring_xfer.rx_buf = &st->rx_buf[0];
&pointer[0] -> pointer
> + st->ring_xfer.len = cmds * sizeof(st->tx_buf[0]);
> +
> + spi_message_init_with_transfers(&st->ring_msg, &st->ring_xfer, 1);
> +
> + return 0;
> +}
> +
> +static irqreturn_t adc108s102_trigger_handler(int irq, void *p)
> +{
> + struct iio_poll_func *pf = p;
> + struct iio_dev *indio_dev;
> + struct adc108s102_state *st;
> + int ret;
> +
> + indio_dev = pf->indio_dev;
> + st = iio_priv(indio_dev);
Assign them above.
> +out:
I would name it out_notify.
> + iio_trigger_notify_done(indio_dev->trig);
> +
> + return IRQ_HANDLED;
> +}
> +static int adc108s102_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long m)
> +{
> + int ret;
> + struct adc108s102_state *st;
Reversed tree order.
> +
> + st = iio_priv(indio_dev);
> +
Assign it above.
> + switch (m) {
> + case IIO_CHAN_INFO_RAW:
> + ret = iio_device_claim_direct_mode(indio_dev);
> + if (ret)
> + return ret;
> +
> + ret = adc108s102_scan_direct(st, chan->address);
> +
> + iio_device_release_direct_mode(indio_dev);
> +
> + if (ret < 0)
> + return ret;
> +
> + *val = ADC108S102_RES_DATA(ret);
> +
> + return IIO_VAL_INT;
> + case IIO_CHAN_INFO_SCALE:
> + switch (chan->type) {
> + case IIO_VOLTAGE:
> + if (st->reg)
> + *val = regulator_get_voltage(st->reg) / 1000;
> + else
> + *val = st->ext_vin_mv;
> +
> + *val2 = chan->scan_type.realbits;
> + return IIO_VAL_FRACTIONAL_LOG2;
> + default:
> + return -EINVAL;
Switch-case for one case? Are you expecting more in the future?
Here I have no strong opinion, so, leave what you / maintainers prefer.
> + }
> + default:
> + return -EINVAL;
> + }
> +}
> +static int adc108s102_probe(struct spi_device *spi)
> +{
> + struct adc108s102_state *st;
> + struct iio_dev *indio_dev;
> + u32 val;
> + int ret;
> +
> + indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + st = iio_priv(indio_dev);
> +
> + ret = device_property_read_u32(&spi->dev, "ext-vin-microvolt", &val);
Why not to read u16 here?
> + if (ret < 0) {
> + dev_err(&spi->dev,
> + "Missing ext-vin-microvolt device property\n");
> + return -ENODEV;
> + }
> + st->ext_vin_mv = (u16)val;
Casting is not needed.
> +
> + /* Use regulator, if available. */
> + st->reg = devm_regulator_get(&spi->dev, "vref");
Here is most important concern, how you get this regulator in ACPI
case in the future? To me it sounds more like
devm_regulator_get_optional();
> + if (IS_ERR(st->reg)) {
> + dev_err(&spi->dev, "Cannot get 'vref' regulator\n");
> + return PTR_ERR(st->reg);
> + }
> + ret = regulator_enable(st->reg);
> + if (ret < 0) {
> + dev_err(&spi->dev, "Cannot enable vref regulator\n");
> + return ret;
> + }
> +
> + spi_set_drvdata(spi, indio_dev);
> + st->spi = spi;
> +
> + indio_dev->name = spi->modalias;
> + indio_dev->dev.parent = &spi->dev;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->channels = adc108s102_channels;
> + indio_dev->num_channels = ARRAY_SIZE(adc108s102_channels);
> + indio_dev->info = &adc108s102_info;
> +
> + /* Setup default message */
> + st->scan_single_xfer.tx_buf = st->tx_buf;
> + st->scan_single_xfer.rx_buf = st->rx_buf;
> + st->scan_single_xfer.len = 2 * sizeof(st->tx_buf[0]);
> +
> + spi_message_init_with_transfers(&st->scan_single_msg,
> + &st->scan_single_xfer, 1);
> +
> + ret = iio_triggered_buffer_setup(indio_dev, NULL,
> + &adc108s102_trigger_handler, NULL);
> + if (ret)
> + goto error_disable_reg;
> +
> + ret = iio_device_register(indio_dev);
I suppose some of above is already under devres API (implicitly when
devm_iio_..._alloc() is in use)
> + if (ret) {
> + dev_err(&spi->dev, "Failed to register IIO device\n");
> + goto error_cleanup_ring;
> + }
> + return 0;
> +
> +error_cleanup_ring:
> + iio_triggered_buffer_cleanup(indio_dev);
Do you need it when devm_ used?
> +error_disable_reg:
> + regulator_disable(st->reg);
Ditto.
> +
> + return ret;
> +}
> +
> +static int adc108s102_remove(struct spi_device *spi)
> +{
> + struct iio_dev *indio_dev = spi_get_drvdata(spi);
> + struct adc108s102_state *st = iio_priv(indio_dev);
> +
> + iio_device_unregister(indio_dev);
> + iio_triggered_buffer_cleanup(indio_dev);
> +
> + regulator_disable(st->reg);
Ditto.
> +
> + return 0;
> +}
> +
> +static struct spi_driver adc108s102_driver = {
> + .driver = {
> + .name = "adc108s102",
> + .owner = THIS_MODULE,
This is redundant I'm pretty sure.
> + .acpi_match_table = ACPI_PTR(adc108s102_acpi_ids),
> + },
> + .probe = adc108s102_probe,
> + .remove = adc108s102_remove,
> + .id_table = adc108s102_id,
> +};
--
With Best Regards,
Andy Shevchenko
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
