On Sat, Jan 28, 2017 at 03:01:42PM +0000, Jonathan Cameron wrote: > On 25/01/17 09:25, Eva Rachel Retuya wrote: > > Add basic IIO support for the Analog Devices ADXL345 3-axis accelerometer. > > The datasheet can be found here: > > http://www.analog.com/media/en/technical-documentation/data-sheets/ADXL345.pdf > > > > Signed-off-by: Eva Rachel Retuya <eraretuya@xxxxxxxxx> > > Cc: Michael Hennerich <michael.hennerich@xxxxxxxxxx> > > Cc: Daniel Baluta <daniel.baluta@xxxxxxxxx> > > Cc: Alison Schofield <amsfield22@xxxxxxxxx> > Nicely presented patch and looks good to me. > > Looking forward to additional features as you get them implemented. > Post early and post often! > > If we were talking a new part with no existing support, we'd only really > need scale and then I'd be happy to merge it. However, at the very > least here you need some protection of both drivers trying to bind to > it at the same time. > > Dmitry (input maintainer) has always been in favour of moving these > out of input eventually so should be happy to take some Kconfig > magic to allow you to develop in parallel until it's ready as a > complete replacement. > Hello Jonathan, Thanks for the input, will work on the points you described above and will send a v2 ASAP. Eva > Thanks, > > Jonathan > > --- > > Note that this sensor is already supported in input/misc/adxl34x. This IIO > > driver only supports read_raw on x, y and z axes in full-resolution mode. > > > > drivers/iio/accel/Kconfig | 10 +++ > > drivers/iio/accel/Makefile | 1 + > > drivers/iio/accel/adxl345.c | 173 ++++++++++++++++++++++++++++++++++++++++++++ > > 3 files changed, 184 insertions(+) > > create mode 100644 drivers/iio/accel/adxl345.c > > > > diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig > > index ea295fe..b73f403 100644 > > --- a/drivers/iio/accel/Kconfig > > +++ b/drivers/iio/accel/Kconfig > > @@ -5,6 +5,16 @@ > > > > menu "Accelerometers" > > > > +config ADXL345 > > + tristate "Analog Devices ADXL345 3-Axis Digital Accelerometer Driver" > > + depends on I2C > > + help > > + Say Y here if you want to build support for the Analog Devices > > + ADXL345 3-axis digital accelerometer. > > + > > + To compile this driver as a module, choose M here: the > > + module will be called adxl345. > > + > > config BMA180 > > tristate "Bosch BMA180/BMA250 3-Axis Accelerometer Driver" > > depends on I2C > > diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile > > index 69fe8ed..618488d 100644 > > --- a/drivers/iio/accel/Makefile > > +++ b/drivers/iio/accel/Makefile > > @@ -3,6 +3,7 @@ > > # > > > > # When adding new entries keep the list in alphabetical order > > +obj-$(CONFIG_ADXL345) += adxl345.o > > obj-$(CONFIG_BMA180) += bma180.o > > obj-$(CONFIG_BMA220) += bma220_spi.o > > obj-$(CONFIG_BMC150_ACCEL) += bmc150-accel-core.o > > diff --git a/drivers/iio/accel/adxl345.c b/drivers/iio/accel/adxl345.c > > new file mode 100644 > > index 0000000..54ea601 > > --- /dev/null > > +++ b/drivers/iio/accel/adxl345.c > > @@ -0,0 +1,173 @@ > > +/* > > + * ADXL345 3-Axis Digital Accelerometer > > + * > > + * Copyright (c) 2017 Eva Rachel Retuya <eraretuya@xxxxxxxxx> > > + * > > + * This file is subject to the terms and conditions of version 2 of > > + * the GNU General Public License. See the file COPYING in the main > > + * directory of this archive for more details. > > + * > > + * IIO driver for ADXL345 > > + * 7-bit I2C slave address: 0x1D (ALT ADDRESS pin tied to VDDIO) or > > + * 0x53 (ALT ADDRESS pin grounded) > > + */ > > + > > +#include <linux/i2c.h> > > +#include <linux/module.h> > > + > > +#include <linux/iio/iio.h> > > + > > +#define ADXL345_REG_DEVID 0x00 > > +#define ADXL345_REG_POWER_CTL 0x2D > > +#define ADXL345_REG_DATA_FORMAT 0x31 > > +#define ADXL345_REG_DATAX0 0x32 > > +#define ADXL345_REG_DATAY0 0x34 > > +#define ADXL345_REG_DATAZ0 0x36 > > + > > +#define ADXL345_POWER_CTL_MEASURE BIT(3) > > +#define ADXL345_POWER_CTL_STANDBY 0x00 > > + > > +#define ADXL345_DATA_FORMAT_FULL_RES BIT(3) > > +#define ADXL345_DATA_FORMAT_2G 0 > > +#define ADXL345_DATA_FORMAT_4G 1 > > +#define ADXL345_DATA_FORMAT_8G 2 > > +#define ADXL345_DATA_FORMAT_16G 3 > > + > > +#define ADXL345_DEVID 0xE5 > > + > > +struct adxl345_data { > > + struct i2c_client *client; > > + u8 data_range; > > +}; > > + > > +#define ADXL345_CHANNEL(reg, axis) { \ > > + .type = IIO_ACCEL, \ > > + .modified = 1, \ > > + .channel2 = IIO_MOD_##axis, \ > > + .address = reg, \ > > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ > > +} > > + > > +static const struct iio_chan_spec adxl345_channels[] = { > > + ADXL345_CHANNEL(ADXL345_REG_DATAX0, X), > > + ADXL345_CHANNEL(ADXL345_REG_DATAY0, Y), > > + ADXL345_CHANNEL(ADXL345_REG_DATAZ0, Z), > > +}; > > + > > +static int adxl345_read_raw(struct iio_dev *indio_dev, > > + struct iio_chan_spec const *chan, > > + int *val, int *val2, long mask) > > +{ > > + struct adxl345_data *data = iio_priv(indio_dev); > > + int ret; > > + > > + switch (mask) { > > + case IIO_CHAN_INFO_RAW: > > + /* > > + * Data is stored in adjacent registers: > > + * ADXL345_REG_DATA(X0/Y0/Z0) contain the least significant byte > > + * and ADXL345_REG_DATA(X0/Y0/Z0) + 1 the most significant byte > > + */ > > + ret = i2c_smbus_read_word_data(data->client, chan->address); > > + > > + if (ret < 0) > > + return ret; > > + > > + *val = sign_extend32(le16_to_cpu(ret), 12); > > + return IIO_VAL_INT; > > + } > > + > > + return -EINVAL; > > +} > > + > > +static const struct iio_info adxl345_info = { > > + .driver_module = THIS_MODULE, > > + .read_raw = adxl345_read_raw, > > +}; > > + > > +static int adxl345_probe(struct i2c_client *client, > > + const struct i2c_device_id *id) > > +{ > > + struct adxl345_data *data; > > + struct iio_dev *indio_dev; > > + int ret; > > + > > + ret = i2c_smbus_read_byte_data(client, ADXL345_REG_DEVID); > > + if (ret < 0) { > > + dev_err(&client->dev, "Error reading device ID: %d\n", ret); > > + return ret; > > + } > > + > > + if (ret != ADXL345_DEVID) { > > + dev_err(&client->dev, "Invalid device ID: %d\n", ret); > > + return -ENODEV; > > + } > > + > > + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); > > + if (!indio_dev) > > + return -ENOMEM; > > + > > + data = iio_priv(indio_dev); > > + i2c_set_clientdata(client, indio_dev); > > + data->client = client; > > + /* Enable full-resolution mode */ > > + data->data_range = ADXL345_DATA_FORMAT_FULL_RES; > > + > > + ret = i2c_smbus_write_byte_data(data->client, ADXL345_REG_DATA_FORMAT, > > + data->data_range); > > + if (ret < 0) { > > + dev_err(&client->dev, "Failed to set data range: %d\n", ret); > > + return ret; > > + } > > + > > + indio_dev->dev.parent = &client->dev; > > + indio_dev->name = id->name; > > + indio_dev->info = &adxl345_info; > > + indio_dev->modes = INDIO_DIRECT_MODE; > > + indio_dev->channels = adxl345_channels; > > + indio_dev->num_channels = ARRAY_SIZE(adxl345_channels); > > + > > + /* Enable measurement mode */ > > + ret = i2c_smbus_write_byte_data(data->client, ADXL345_REG_POWER_CTL, > > + ADXL345_POWER_CTL_MEASURE); > > + if (ret < 0) { > > + dev_err(&client->dev, "Failed to enable measurement mode: %d\n", > > + ret); > > + return ret; > > + } > > + > > + return iio_device_register(indio_dev); > > +} > > + > > +static int adxl345_remove(struct i2c_client *client) > > +{ > > + struct iio_dev *indio_dev = i2c_get_clientdata(client); > > + struct adxl345_data *data = iio_priv(indio_dev); > > + > > + iio_device_unregister(indio_dev); > > + > > + return i2c_smbus_write_byte_data(data->client, ADXL345_REG_POWER_CTL, > > + ADXL345_POWER_CTL_STANDBY); > > +} > > + > > +static const struct i2c_device_id adxl345_i2c_id[] = { > > + { "adxl345", 0 }, > > + { } > > +}; > > + > > +MODULE_DEVICE_TABLE(i2c, adxl345_i2c_id); > > + > > +static struct i2c_driver adxl345_driver = { > > + .driver = { > > + .name = "adxl345", > > + }, > > + .probe = adxl345_probe, > > + .remove = adxl345_remove, > > + .id_table = adxl345_i2c_id, > > +}; > > + > > +module_i2c_driver(adxl345_driver); > > + > > +MODULE_AUTHOR("Eva Rachel Retuya <eraretuya@xxxxxxxxx>"); > > +MODULE_DESCRIPTION("ADXL345 3-Axis Digital Accelerometer driver"); > > +MODULE_LICENSE("GPL v2"); > > > -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
