On Mon, Jan 23, 2017 at 05:32:19PM +0100, Arnaud Pouliquen wrote:
> Add bindings information for STM32 Digital Filter for Sigma Delta modulators MFD driver
>
> Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@xxxxxx>
> ---
> .../devicetree/bindings/mfd/stm32-dfsdm.txt | 68 ++++++++++++++++++++++
> 1 file changed, 68 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/stm32-dfsdm.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/stm32-dfsdm.txt b/Documentation/devicetree/bindings/mfd/stm32-dfsdm.txt
> new file mode 100644
> index 0000000..e0b45ee
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/stm32-dfsdm.txt
> @@ -0,0 +1,68 @@
> +STMicroelectronics STM32 Digital Filter for Sigma Delta Modulator (DFSDM)
> +ulti-function device.
> +
> +The STM32 DFSDM device is a multifunction device that handles the DFSDM IP.
> +
> +The DFSDM IP allows to add processing on Sigma Delta ADC based on SinC filters.
> +For this, a pool of m filters can be connected to a pool of n channels.
> +For STM32H7 : m = 4, n = 8.
> +
> +Each channel n is assigned to the SPI or Manchester interface n or n + 1.
> +Channels 0 to 2 can also be connected to ADC IP instance 1 to 3.
> +Filtering result is stored in a left aligned register, with 8 LSB reserved for
> +the input channel ID.
> +
> +Each filter instance supports two contexts to manage conversions, each one has
> +its own configurable sequence and trigger:
> +- regular conversion: used for single or continuous conversion.
> +- injected conversions: used for triggered conversion.
> +
> +Interfaces supported:
> +- sigma delta ADCs trough IIO framework.
> +- PDM microphones through ASoC framework.
Bindings describe h/w, not Linux subsystems.
> +
> +Required properties:
> +- compatible: Must be "st,stm32h7-dfsdm".
> +- reg: Specifies the DFSDM block register address and length.
> +- interrupts: IRQ lines connected to each DFSDM filter instance.
> +- clocks: IP and serial interfaces clocking. Should be set according
> + to rcc clock ID and "clock-names".
> +- clock-names: Input clock name "dfsdm_clk" must be defined,
> + "audio_clk" is optional. If defined CLKOUT is based on the audio
> + clock, else "dfsdm_clk" is used.
_clk is redundant.
> +
> +Optional properties:
> +- st,clkout-freq: clkout clock frequency (Hz).This clock must be set according
> + to "clock" property. Frequency must be a multiple of the rcc
> + clock frequency. If not, clkout frequency will not be
> + accurate.
What is CLKOUT connected to and will you need to describe that in DT?
> +- pinctrl-names: set to "default".
> +- pinctrl-0: List of phandles pointing to pin configuration nodes for DFSDM
> + module.
> + For Pinctrl properties see ../pinctrl/pinctrl-bindings.txt
> +Example :
> + dfsdm: dfsdm@4400D000 {
> + compatible = "st,stm32h7-dfsdm";
> + reg = <0x40017000 0x400>;
> + interrupts = <110>, <111>, <112>, <113>;
> + clocks = <&timer_clk>;
> + clock-names = "dfsdm_clk";
> + pinctrl-0 = <&dfsdm_ch0 &dfsdm_ch1>;
> + pinctrl-names = "default";
> + st,clkout-freq = <2480000>;
> +
> + iio_dfsdm0: iio-dfsdm@0 {
adc {
> + compatible = "st,stm32-dfsdm-adc";
> + #io-channel-cells = <1>;
> + reg = <0>;
> + status = "disabled";
> + };
> + dai_dfsdm0: dfsdm-audio@0 {
digital-mic {
> + compatible = "st,stm32-dfsdm-audio";
> + #sound-dai-cells = <0>;
> + reg = <0>;
You can't have 2 children with the same unit address. Just drop reg and
the unit address.
> + dmas = <&dmamux1 101 0x400 0x00>;
> + dma-names = "rx";
> + status = "disabled";
> + };
> + };
> --
> 1.9.1
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
